Diesel Fill w/ Locking Cap for 1-1/2" Hose (0599) Chrome Plated Zinc Alloy Flange Black Plastic Body Black Plastic Cap w/ Strap Grounding Screw Included Cap Retainer and Gasket Locking Cap has a cover for the key hole Tech Info for Hose Size: 1-1/2" O.D. Flange: 3-3/8" Length of Neck: 3-1/8" Mounting Hole Dia.: 2-1/8" Screw Size: #8

Gas Fill w/ Locking Cap for 1-1/2" Hose (0599) Chrome Plated Zinc Alloy Flange Black Plastic Body Black Plastic Cap w/ Strap Grounding Screw Included Cap Retainer and Gasket Locking Cap has a cover for the key hole Tech Info for Hose Size: 1-1/2" O.D. Flange: 3-1/8" Length of Neck: 3-1/8" Mounting Hole Dia.: 2-1/8" Screw Size: #8

As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away. Outside Storage? It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.                          Rinse/Flush Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat. Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring. Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present. Salt Watch out for salt. Buy a good salt remover to minimize corrosion. Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine. Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4* STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel. Batteries Remove the batteries from your boat and store in your garage or basement. Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery. If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat. Cleaning Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint. Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins. Cover Up If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often. https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html and https://www.clrmarine.com/462m4/winterizing.html Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information. Fair winds and smooth sailing.   To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/. _________________________________________________________________________ Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten. She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com ©Copyright Cheryl Kuba, 3happycampers.com, 2021.  

Fuel System Locking Cap f/ 1-1/2" Non-Vented Fills (1324) Black Plastic with Gasket Built in Lock Cylinder Size #0 Fits PERKO Fills 1313 & 1399 Cap Outside Thread Diameter: 1-15/32"

360® Marine™ - 1 Gallon CLEANS THE FUEL SYSTEM TO IMPROVE PERFORMANCE STA-BIL 360® MARINE™ use it with every fill up to help keep your engine running cleaner, leaner, smoother and stronger than ever. USAGE DIRECTIONS: 1oz treats up to 10 gallons (38 liters) of fuel.  Product does not contain alcohol. Perfect for use in all boats, jet skies, and other watersport engines. 5-IN-1 MAXIMIZER HELPS TAKE PERFORMANCE OVER THE TOP PREVENT ETHANOL DAMAGE: Protect your entire fuel system against damaging rust and corrosion caused by moisture and ethanol fuels. Provides a protective coating on ALL the metal parts of the entire fuel system and combustion chamber, even when the engine is not running. INCREASE POWER: Strip away carbon buildup, gum and varnish that can inhibit engine performance, and get the most out of your fuel by burning it more completely. Bring back the power your engine once knew. Clear and prevent harmful gum, varnish and buildup throughout the combustion chamber and injectors. MAXIMIZE FUEL ECONOMY: Burn fuel more completely and efficiently by preserving the fuel system and engine. Features: America’s #1 Ethanol Treatment Use for storage or use at every fill-up and keep marine fuel fresh for up to 12 months Effective in Non-Ethanol marine fuels Cleans the fuel system to improve performance Increases power and fuel efficiency in marine fuel systems & engines Use in your boat, jet ski, or any water sport engines Ultimate treatment and protection formula for ethanol and condensation Made in the U.S.A. WARNING: This product can expose you to chemicals including benzene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

360® Marine™ - 1 Gallon *Case of 4* CLEANS THE FUEL SYSTEM TO IMPROVE PERFORMANCE STA-BIL 360® MARINE™ use it with every fill up to help keep your engine running cleaner, leaner, smoother and stronger than ever. USAGE DIRECTIONS: 1oz treats up to 10 gallons (38 liters) of fuel.  Product does not contain alcohol. Perfect for use in all boats, jet skies, and other watersport engines. 5-IN-1 MAXIMIZER HELPS TAKE PERFORMANCE OVER THE TOP PREVENT ETHANOL DAMAGE: Protect your entire fuel system against damaging rust and corrosion caused by moisture and ethanol fuels. Provides a protective coating on ALL the metal parts of the entire fuel system and combustion chamber, even when the engine is not running. INCREASE POWER: Strip away carbon buildup, gum and varnish that can inhibit engine performance, and get the most out of your fuel by burning it more completely. Bring back the power your engine once knew. Clear and prevent harmful gum, varnish and buildup throughout the combustion chamber and injectors. MAXIMIZE FUEL ECONOMY: Burn fuel more completely and efficiently by preserving the fuel system and engine. Features: America’s #1 Ethanol Treatment Use for storage or use at every fill-up and keep marine fuel fresh for up to 12 months Effective in Non-Ethanol marine fuels Cleans the fuel system to improve performance Increases power and fuel efficiency in marine fuel systems & engines Use in your boat, jet ski, or any water sport engines Ultimate treatment and protection formula for ethanol and condensation Made in the U.S.A. WARNING: This product can expose you to chemicals including benzene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

316 Stainless Steel Alloy Flush Mount Fuel Vent - 90° Vent On the exterior, they have a smooth edge over the competition. Unlike some others, there is no protruding cap to cause damage or be damaged by hull bumps and scrapes. Cap unscrews with a hex head wrench for easy cleaning of the filter and pressure testing of the entire fuel system. These vents now include two silicone gaskets. Features: 90-degree vent Specifications: Hose Size (inch): 5/8" inner diameter Maximum Hull Thickness (inch): 7/8" Installation Hole Size (inch): 1-3/8" *Includes two silicone gaskets

Emergency Deck Fill Plug Nitrile-Buna Rubber This Emergency Deck Fill Plug is a must for any vessel. Fits most 1-1/2" hose deck fills in the event you lose your cap. For temporary use only until you can replace your OEM cap. Constructed of fuel resistant Nitrile-Buna rubber. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Replacement fill plugs for SeaStar hydraulic helms.

Walbro FRB-13-2 Fuel Pump 6-8 Psi 12V Pressure: 6.0 - 8.0 psi Service Life: 18,000+ hr Magnetic Trap: Yes Minimum Flow Rate: 43 gph Dry Lift: 48" Current Draw: 2.3 Amp Inlet/Outlet: 1/4-18 NPSF Fuse: 5A Inlet Filter Screen: 70 Micron Weight: 1.83 lb Voltage: 12V DC Outlet Check Valve: None   The FRB is an advanced electric fuel pump with internal circuitry allowing it to operate at a variable frequency. When turned on, it will cycle as long as there is a demand for fuel, but when fuel demand decreases, the pump slows down as it builds pressure in the fuel delivery line - until the pump's rated maximum pressure is reached, and the pump stops. These FRB pumps are especially suitable for applications where battery life, low noise, and best durability are important. Not recommended for applications such as heater or stove systems as output pressures are too high. For heater and stove fuel pumps, use the lower pressure Walbro FRD Series. See Related Products, below. The FRB is designed to serve as a primary pump (replacing a mechanical fuel pump) or as an auxilliary fuel pump (assisting the existing pump) for internal combustion engines. A common application is supplying fuel to the those diesel refrigeration units mounted high on tractor-trailer trucks. These pumps incorporate a new piston mechanism which, unlike rubber diaphragms, is not affected by modern, high-tech fuel blends. • Pump cycles only when fuel is demanded - so the pump cycles on and off • The non-adjustable maximum output pressure is factory pre-set in the ranges specified in the table, below • Continuous duty life (diesel fuel): >18,000 hours • Can run dry for up to 4 hours • Flow rates as high as 60 gph, but 30 gph is a more typical maximum • Compatible with all commercially available pump grade gasoline, gasoline-alcohol blends, diesel, and bio-diesel fuels • Self-priming to 4 feet • Current draw averages less than 2 amps • USCG 16623-1 and 16623-2 approved; ignition protected • Anodized, corrosion protection coating passes 1,000 hr salt spray test - suitable for marine applications • Replaceable internal 70 micron mesh filter • Magnetic trap for ferrous contaminants • Inlet (lower, side)/Outlet (top): 1/4-18 NPSF (Dryseal American National Standard Straight Pipe Thread) — will accept NPT tapered fittings without leaking, thread sealant recommended • Dimensions: 5.83"H x 2.76"Dia. • Note - a suffix number (typically -1 or -2) in part number refers to type of packaging • Made in USA NOTE — Although the included instructions indicate that FRB pumps are supplied with hose clamps, at this time (5/8/13), these pumps do not include any installation fittings. Technical Selecting among the Walbro FR Series electric fuel pumps: • All the FR electric pumps provide fuel until the fuel demand decreases, or flow is restricted - but they have different mechanisms for doing so. FR pumps will cycle (pump) until they build up the pressure (head) in the outflow line - with an accompanying decrease in fuel flow - and reach their factory preset maximum pressure. At this point, constant frequency pumps like the FRA will continue cycling - but no fuel will flow. Variable frequency pumps, like the FRB and FRD, will slow and eventually stop cycling as the pressure builds. If the pressure on the outflow side of the pump drops, both types of pump will start supplying fuel again. • Choosing an FR Series pump is often less dependent on the application, and more a matter of user preference: — FRA pumps are lower cost, basic models. They have no built-in filter, and their constant cycling means electric current draw is constant - regardless of output, they are always making noise, they typically have a shorter lifespan (higher wear), and they can wear unevenly as the stroke can be shortened when operating near their maximal pressure. — FRB and FRD pumps have a more expensive variable frequency circuit board, always use their full stroke length - so wear is evenly distributed, do not always operate at full capacity/maximal cycling — so less wear, longer life, less noise, and lower average current draw. Additionally, the FRB models include a built-in/replaceable 70 micron mesh filter, so the user doesn't need to supply a pre-filter.   • What the FR fuel pump is designed to do: — In carbureted applications - The FRA and FRB fuel pumps self-regulate to their maximum output pressure when the carburetor bowl is full, and respond to float movement in the carburetor as required. When the engine demands more fuel, the pump increases its flow rate. When the engine demand drops, the pump reduces its flow rate. — In diesel applications - The FRA and FRB pumps will deliver fuel to the diesel injector pump, assuring a positive pressure at the injector pump inlet. These pumps are designed to refill diesel filters after service or replacement. — In transfer applications, including fuel polishing, FRA and FRB pumps run continuously, as long as electrical power is supplied to the pump, and output back pressure is low. — In diesel heater and stove applications, the task-specific FRD pumps will slow their cycling rate to deliver only the fuel required by the stove fuel metering valve ("carburetor"). FRD pumps can also fill day tanks in gravity feed installations. • Complete list of approved fuels for FR pumps: — Unleaded regular gasoline, premium gasoline, gasoline-alcohol blends, diesel fuel, bio-diesel, Stoddard solvent, E85.  

Walbro FRB-16-2 24V Fuel Pump 6-8 Psi Outlet Check Valve: None Voltage: 24V DC Weight: 1.83 lb Magnetic Trap: Yes Minimum Flow Rate: 43 gph Dry Lift: 48" Current Draw: 1.7 Amp Inlet/Outlet: 1/4-18 NPSF Fuse: 5A Inlet Filter Screen: 70 Micron Service Life: 18,000+ hr Pressure: 6.0 - 8.0 psi   The FRB is an advanced electric fuel pump with internal circuitry allowing it to operate at a variable frequency. When turned on, it will cycle as long as there is a demand for fuel, but when fuel demand decreases, the pump slows down as it builds pressure in the fuel delivery line - until the pump's rated maximum pressure is reached, and the pump stops. These FRB pumps are especially suitable for applications where battery life, low noise, and best durability are important. Not recommended for applications such as heater or stove systems as output pressures are too high. For heater and stove fuel pumps, use the lower pressure Walbro FRD Series. See Related Products, below. The FRB is designed to serve as a primary pump (replacing a mechanical fuel pump) or as an auxilliary fuel pump (assisting the existing pump) for internal combustion engines. A common application is supplying fuel to the those diesel refrigeration units mounted high on tractor-trailer trucks. These pumps incorporate a new piston mechanism which, unlike rubber diaphragms, is not affected by modern, high-tech fuel blends. • Pump cycles only when fuel is demanded - so the pump cycles on and off • The non-adjustable maximum output pressure is factory pre-set in the ranges specified in the table, below • Continuous duty life (diesel fuel): >18,000 hours • Can run dry for up to 4 hours • Flow rates as high as 60 gph, but 30 gph is a more typical maximum • Compatible with all commercially available pump grade gasoline, gasoline-alcohol blends, diesel, and bio-diesel fuels • Self-priming to 4 feet • Current draw averages less than 2 amps • USCG 16623-1 and 16623-2 approved; ignition protected • Anodized, corrosion protection coating passes 1,000 hr salt spray test - suitable for marine applications • Replaceable internal 70 micron mesh filter • Magnetic trap for ferrous contaminants • Inlet (lower, side)/Outlet (top): 1/4-18 NPSF (Dryseal American National Standard Straight Pipe Thread) — will accept NPT tapered fittings without leaking, thread sealant recommended • Dimensions: 5.83"H x 2.76"Dia. • Note - a suffix number (typically -1 or -2) in part number refers to type of packaging • Made in USA NOTE — Although the included instructions indicate that FRB pumps are supplied with hose clamps, at this time (5/8/13), these pumps do not include any installation fittings. Technical Selecting among the Walbro FR Series electric fuel pumps: • All the FR electric pumps provide fuel until the fuel demand decreases, or flow is restricted - but they have different mechanisms for doing so. FR pumps will cycle (pump) until they build up the pressure (head) in the outflow line - with an accompanying decrease in fuel flow - and reach their factory preset maximum pressure. At this point, constant frequency pumps like the FRA will continue cycling - but no fuel will flow. Variable frequency pumps, like the FRB and FRD, will slow and eventually stop cycling as the pressure builds. If the pressure on the outflow side of the pump drops, both types of pump will start supplying fuel again. • Choosing an FR Series pump is often less dependent on the application, and more a matter of user preference: FRA pumps are lower cost, basic models. They have no built-in filter, and their constant cycling means electric current draw is constant - regardless of output, they are always making noise, they typically have a shorter lifespan (higher wear), and they can wear unevenly as the stroke can be shortened when operating near their maximal pressure. FRB and FRD pumps have a more expensive variable frequency circuit board, always use their full stroke length - so wear is evenly distributed, do not always operate at full capacity/maximal cycling — so less wear, longer life, less noise, and lower average current draw. Additionally, the FRB models include a built-in/replaceable 70 micron mesh filter, so the user doesn't need to supply a pre-filter. • What the FR fuel pump is designed to do: In carbureted applications - The FRA and FRB fuel pumps self-regulate to their maximum output pressure when the carburetor bowl is full, and respond to float movement in the carburetor as required. When the engine demands more fuel, the pump increases its flow rate. When the engine demand drops, the pump reduces its flow rate. In diesel applications - The FRA and FRB pumps will deliver fuel to the diesel injector pump, assuring a positive pressure at the injector pump inlet.   These pumps are designed to refill diesel filters after service or replacement. In transfer applications, including fuel polishing, FRA and FRB pumps run continuously, as long as electrical power is supplied to the pump, and output back pressure is low. In diesel heater and stove applications, the task-specific FRD pumps will slow their cycling rate to deliver only the fuel required by the stove fuel metering valve ("carburetor"). FRD pumps can also fill day tanks in gravity feed installations. • Complete list of approved fuels for FR pumps: Unleaded regular gasoline, premium gasoline, gasoline-alcohol blends, diesel fuel, bio-diesel, Stoddard solvent, E85.  

0590 Angled Water Fill/Vent Features: Chrome Plated Bronze Cap Black Polymer Body Stainless Steel Bead Chain Integral Tank Vent with Flame Arrestor and Anti Surge Valve (on diesel only) Deck Plate Key Not Required Specifications: For Hose Size: 1-1/2" For Vent Hose: 5/8" Mounting Hole Dia.: 2-1/8" O.D. Flange: 3-3/8" Neck Length: 2-7/16" Screw Size: #8

Walbro FRB-23-2 24V Fuel Pump 8-11 Psi Pressure: 8.0 - 11.0 psi Outlet Check Valve: None Magnetic Trap: Yes Minimum Flow Rate: 43 gph Dry Lift: 48" Current Draw: 1.7 Amp Inlet/Outlet: 1/4-18 NPSF Fuse: 5A Inlet Filter Screen: 70 Micron Service Life: 18,000+ hr Voltage: 24V DC Weight: 1.83 lb   The FRB is an advanced electric fuel pump with internal circuitry allowing it to operate at a variable frequency. When turned on, it will cycle as long as there is a demand for fuel, but when fuel demand decreases, the pump slows down as it builds pressure in the fuel delivery line - until the pump's rated maximum pressure is reached, and the pump stops. These FRB pumps are especially suitable for applications where battery life, low noise, and best durability are important. Not recommended for applications such as heater or stove systems as output pressures are too high. For heater and stove fuel pumps, use the lower pressure Walbro FRD Series. See Related Products, below. The FRB is designed to serve as a primary pump (replacing a mechanical fuel pump) or as an auxilliary fuel pump (assisting the existing pump) for internal combustion engines. A common application is supplying fuel to the those diesel refrigeration units mounted high on tractor-trailer trucks. These pumps incorporate a new piston mechanism which, unlike rubber diaphragms, is not affected by modern, high-tech fuel blends. • Pump cycles only when fuel is demanded - so the pump cycles on and off • The non-adjustable maximum output pressure is factory pre-set in the ranges specified in the table, below • Continuous duty life (diesel fuel): >18,000 hours • Can run dry for up to 4 hours • Flow rates as high as 60 gph, but 30 gph is a more typical maximum • Compatible with all commercially available pump grade gasoline, gasoline-alcohol blends, diesel, and bio-diesel fuels • Self-priming to 4 feet • Current draw averages less than 2 amps • USCG 16623-1 and 16623-2 approved; ignition protected • Anodized, corrosion protection coating passes 1,000 hr salt spray test - suitable for marine applications • Replaceable internal 70 micron mesh filter • Magnetic trap for ferrous contaminants • Inlet (lower, side)/Outlet (top): 1/4-18 NPSF (Dryseal American National Standard Straight Pipe Thread) — will accept NPT tapered fittings without leaking, thread sealant recommended • Dimensions: 5.83"H x 2.76"Dia. • Note - a suffix number (typically -1 or -2) in part number refers to type of packaging   • Made in USA  

Fuel Flow Sensor with 10' cable & T-connector Fuel Flow Sensor Gasoline ONLY. 1 required per engine. Up to 3 engines supported. Outputs: Fuel Flow Tank Fuel Used Trip Fuel Used Seasonal Fuel Used Cable Length: 10' Fuel Line Diameter: 3/8" (9.5mm) Inside Diameter Flow Rate Measured: Optimized for 0.6-45 Gal/hr but can measure outside these values Added Back Pressure to the fuel system: 0.5 PSI at 20 Gal/hr; 1 PSI at 40 Gal/hr Installation Location: Above the max level of the fuel tank, in-line after the fuel filter and any Y's or T's in the line Package: The Fuel Flow Sensor, N2K T and 2 (two) 1" hose clamps Fuel Type: Gasoline only. The Fuel Flow Sensor does not operate diesel engine fuel systems Hole required to route through a bulkhead: 22mm (7/8") Multiple Fule Flow sensors possible: Yes

RAM Double Socket Arm with Locking Knob for 1.5" Ball Bases The RAM-201LU, standard double socket arm with locking knob, has a socket at both ends that accommodates 1.5" ball bases. A single spring inside the arm opens the end sockets, allowing you to pivot the ball and socket connection. This socket technology allows for almost infinite adjustment and perfect viewing angles. The locking knob, includes a brass 1/4"-20 thread; this allowing you to disengage the screwing of the knob. Once you have set your mount in the location you need, you can lock it in place and feel safe that your mounted device will stay right where you left it. Dimensions: Overall Length: 5.625" Socket-To-Socket Length: 4.5" Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball Size Note: The "U" in the part number reflects product packaged in poly bag.