Economy Chain Stopper f/5/16", 3/8", 8mm & 10mm Chain Chain stoppers hold the chain and take the load off the windlass. They are used to set and ride on the anchor, break free the anchor or to prevent accidental free fall of the anchor while under way. Also recommended for VW series rope and chain systems to hold the chain while changing over from rope to chain. 8/10mm (5/16"/3/8"): B - 62mm (2-3/8") C - 6mm (1/4") F - 80mm (3-1/8") G - 46mm (1-4/4") G1 - 17mm (5/8") I - 92mm (3-5/8") J - N/A J1 - 37mm (1-1/2") K - 74mm (2-7/8") L - N/A M - M10

Levered Chain Stopper f/5/16" or 8mm Chain Chain stoppers hold the chain and take the load off the windlass. They are used to set and ride on the anchor, break free the anchor or to prevent accidental free fall of the anchor while under way. Also recommended for VW series rope and chain systems to hold the chain while changing over from rope to chain. 8mm (5/16"): B - 72mm (2-7/8") C - 20mm (7/8") F - 152mm (6") G - 92mm (3-5/8") G1 - 30mm (1-3/16") I - 70mm (2-7/8") J - 31.5mm (1-1/4") J1 - 10mm (7/16") K - 51.5mm (2-1/8") L - 95mm (3-3/4") M - M10

Stainless Steel Chain Stopper - 5/16" - 3/8" Chain Stoppers help prevent damage to the windlass and reduce the risk of accidental free fall of the anchor while under way. Chain Stoppers mount alone or inside most bow rollers and work with your anchor roller to take tension off your windlass. Chain and rope should be secured at anchor when your windlass is not in use to avoid high loads the windlass was not designed for. 321820 fits chain sizes 3/16" - 1/4". 321825 fits chain sizes 5/16" - 3/8". Constructed of corrosion resistant formed 304 stainless steel.

Lead Battery Terminal - 5/16" & 3/8" Stud - Positive & Negative Combo Pack Stud Size:5/16 " & 3/8" Product Features: Seamless barrel design allows for maximum strength when crimped Closed end design seals out moisture so cables stay dry and corrosion free WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Tinned Battery Terminal - 5/16" & 3/8" Stud - Positive & Negative Combo Pack Stud Size:5/16" & 3/8" Product Features: ANCOR Marine Grade™ lugs are manufactured from heavy duty annealed tinned brass, providing for maximum current flow 100% tin plated brass resists corrosion from salt and moisture Seamless barrel design allows for maximum strength when crimped Closed end design seals out moisture so cables stay dry and corrosion free WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Wrap Pins Hook & Loop Pin Locking Devices for Open Body Turnbuckles 5/16" & 3/8" - 2-Pack Wrap Pins are neat hook and loop locking devices used to secure turnbuckles without messing with unruly cotter pins. Just make your adjustment, push the pin attached to the hook and loop through the hole and wrap the hook and loop strip around the turnbuckle body. Works on open body turnbuckles and Johnson's positive locking, slotted tubular turnbuckles. This size works for 3/32" diameter for 5/16" and 3/8" threads.

12V 1-1/4" Stroke 5 Lobe Actuator - 5/16" - 3/8" Lenco's 12V actuator for ski boats and tow boats.  Includes: Deutsch connector 6' cable and mounting hardware 3/8" hole 12V  1.25" Stroke  XDS Series Replacement Actuator for Tow/Ski Boats WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Universal Sprayless Connector - Hose Female (5/16"-3/8") This Attwood Universal Sprayless Connector reliably eliminates fuel spraying when you are connecting and disconnecting fuel hoses during fueling or maintenance. This connector replaces a traditional fitting and its high-strength body is engineered to withstand the rigors of a marine environment.  Features: Female hose fitting compatible with 3/8" and 5/16" fuel lines Includes check valves that automatically close upon disconnecting High fuel flow fitting (less than .25kPa restriction at 50 liters/hour) Reliably eliminates fuel spraying when connecting and disconnecting the fuel hose *Compatible with Ethanol blended fuels and all OEM-brand engines

Universal Sprayless Connector – Hose Male (5/16"-3/8") This Attwood Universal Sprayless Connector reliably eliminates fuel spraying when you are connecting and disconnecting fuel hoses during fueling or maintenance. Also, this connector replaces a traditional fitting and its high-strength body is engineered to withstand the rigors of a marine environment. The Universal Sprayless Connector – Hose Male, is a female hose fitting compatible with 5/16-In. and 3/8-In. fuel lines. Features:  Male hose fitting compatible with 3/8" and 5/16" fuel lines Includes check valves that automatically close upon disconnecting High fuel flow fitting (less than .25kPa restriction at 50 liters/hour) It meets EPA and CARB requirements *This connector is compatible with Ethanol blended fuels and with all OEM-brand engines

Levered Chain Stopper f/3/8" or 10mm Chain Chain stoppers hold the chain and take the load off the windlass. They are used to set and ride on the anchor, break free the anchor or to prevent accidental free fall of the anchor while under way. Also recommended for VW series rope and chain systems to hold the chain while changing over from rope to chain. 10mm (3/8"): B - 86mm (3-7/16") C - 20mm (7/8") F - 190mm (7-1/2") G - 130mm (5-1/8") G1 - 30mm (1-3/16") I - 86mm (3-1/2") J - 44mm (1-3/4") J1 - 10mm (7/16") K - 64mm (2-5/8") L - 95mm (3-3/4") M - M10

Single-Hook Anchor Chain Tensioner for 5/16" Chain These fittings will securely tension and hold the anchor in the bow roller channel.  They will free up use of the bow cleat and prepare the anchor for sea condition assuring you peace of mind.  This fitting is not designed to take the strain of the rode of a boat at anchor.  "Single Hook" style has overall length of 12", the threaded hook has 1-1/2" of adjustment for ease of installation.

HRC 10-8 Horizontal Windlass 5/16" Chain, 5/8" Rope, 12V, with Capstan Designed for boats up to 45 feet, the HRC10-8 Horizontal Series windlasses proudly follow in the highly successful footsteps of Maxwell's previous, fully automatic rope / chain anchor winches. Kit Includes Windlass On/Off Breaker Panel Reversing Solenoid Up/down Panel Switch Clutch Release Handle Features The HRC10-8 is Maxwell's fully automatic rope/ chain or all chain horizontal windlass Designed to effortlessly retrieve and deploy 8mm (5/16" ) chain and 16mm (5/8" ) three strand or 8-brait (plait) rope. The HRC 10-8 has a patented uniquely designed chain wheel will accommodate ANY 5/16" or 8 mm marine grade chain spliced to 5/8" rope. The aesthetically pleasing above deck design, evolved from the philosophy of form follows function, encapsulates the motor and drive in a two part watertight case, saving space below deck Case Material: Anodized Aluminum The two part case consists of a die cast, marine-grade hard anodised alloy front section and a rugged and easily removable composite motor cover aft section. This two piece watertight case allows for quick and easy, on-deck,routine maintenance. Simple " bolt down" installation ensures effortless and rapid on-deck installation and set up. The stainless steel pressure arm always exerts maximum control pressure on the rode (rope, splice or chain). The new and revolutionary patented Wave Design chainwheel is able to accommodate a wide range of chain pitch differences, within the specified chain size diameters, suitable for use with the HRC10 Series. The unique Maxwell " wrap around" horizontal chainwheel ensures that more than 90x of the wheel is used, allowing greatly improved rope and chain handling compared with competitor designs. High quality Stainless Steel chainwheels The HRC10 works just as effectively with all-chain rodes for those who desire the added security and holding power of an all-chain anchor system. The integral chain pipe and huge, through deck hawse pipe throat ensures easy entry of the rope / chain rode into and out of the anchor locker. Cone type clutch/brake mechanism permits manual, "free fall" anchoring and emergency crank recovery of the rode and anchor if required. The sealed oil bath and marine-grade hard anodised, alloy gearbox provides high efficiency output drive via precision worm and wormwheel. Exclusive Maxwell 3 YEAR Limited Warranty Specifications Maximum PUll: 1540 lbs Chain Short Link: 5/16" or 8mm Chain Speed (Anchor Retrieval): 79 ft per Minute Rope Speed (Anchor Retrieval): 65 ft per Minute Rope Size (Nylon 3 strand or 8 Plait): 5/8" Power Supply (DC): 12VDC Motor Power: 1000 Watts Net weight: 42 lbs This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

HRC10 Horizontal Rope Chain Windlass - 12V No Capstan 3/8" Chain, 5/8" Rope Maxwell's HRC10 represents yet another breakthrough in performance and anchor handling excellence. The horizontal, fully automatic rope/chain windlass has been designed to meet the demands for use on larger vessels up to 16 meters (52'), which require a completely above deck installation system. The HRC10 handles 5/8" rope and 3/8" chain, including the thick rope to chain splice. The modern appearance of the HRC10 retains the classic good looks of previous Maxwell horizontal windlasses, while incorporating design features years ahead of its competitors. The HRC10 windlass is fitted with Maxwell's unique Wave Design™ chainwheel. The rope/chain wheel incorporates two unique design concepts that greatly improve the handling and control of the rope/chain spliced rode. The outer ribs of the chainwheel are angled slightly forward ensuring that the rope and the chain are smoothly guided in the wheel during anchor retrieval. As the rope pulls into the wheel, the opposite facing inner ribs grip the rope in an undulating manner, securing the rope more firmly in a 'wave pattern' action that is far superior to the traditional 'jam cleat' manner of holding the rope. Not only does this Wave Design™ hold the rope more securely, it is also kinder on the rope resulting in increased longevity of your anchor rode. Features: Aesthetically pleasing above deck design, evolved from the philosophy of form follows function, encapsulates the motor and drive in a two part watertight case, saving space below deck 2-part case consists of a die cast, marine-grade hard anodised alloy front section and a rugged and easily removable composite motor cover aft section 2-piece watertight case allows for quick and easy, on-deck, routine maintenance Simple "bolt down" installation ensures effortless and rapid on-deck installation and set up Stainless steel pressure arm always exerts maximum control pressure on the rode (rope, splice or chain) Wave Design™ chainwheel is able to accommodate a wide range of chain pitch differences, within the specified chain size diameters Unique Maxwell "wrap around"™ horizontal chainwheel ensures that more than 90° of the wheel is used, allowing greatly improved rope and chain handling compared with competitor designs The HRC10 works just as effectively with all-chain rodes for those who desire the added security and holding power of an all-chain anchor system The integral chain pipe and huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker Cone type clutch/brake mechanism permits manual, "free fall"™ anchoring and emergency crank recovery of the rode and anchor if required = The sealed oil bath and marine-grade hard anodised, alloy gearbox provides high efficiency output drive via precision worm and wormwheel This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Chain Grip for 5/16" (8mm) Chain Perfect to ensure safe anchoring by easing the tension on the anchor chain. Protects the boat by reducing the chafe of the chain on the rub rail and roller chock. Positioned between two links of the chain (single-handed operation). Optimized design to avoid accidental release of the chain. Features: One-piece with nonmoving parts Forged in Duplex stainless steel grade (increased mechanical & corrosion resistance) Made in France Rope size: 22 mm Specifications: Chain diameter: 8 mm (5/16") Rope diameter: 17 mm (5/8") Working load: 480 kg (1,050 lbs) Breaking load: 890 kg (1,960 lbs) Weight: 88 g (0.194 lbs) Length: 85 mm ( 3-11/32") Applications: Mouillage

Stainless Steel Chain Stopper - 3/16" - 1/4" Chain Stoppers help prevent damage to the windlass and reduce the risk of accidental free fall of the anchor while under way. Chain Stoppers mount alone or inside most bow rollers and work with your anchor roller to take tension off your windlass. Chain and rope should be secured at anchor when your windlass is not in use to avoid high loads the windlass was not designed for. 321820 fits chain sizes 3/16" - 1/4". 321825 fits chain sizes 5/16" - 3/8". Constructed of corrosion resistant formed 304 stainless steel.