RC12-10 12V Windlass EDC - 3/8" Chain & 3/4" Rope The RC12-10 automatic rope/chain windlass is built to effortlessly retrieve and deploy a 3/8 in. short link chain and 5/8" to 3/4 in. 8-Plait rope using Maxwell’s patented Wave Design™ chain wheel. The RC12 is a highly versatile windlass offering multiple configurations (anti-clockwise, capstan, low profile, extended deck clearance, etc.) and is packed with patented features showcasing the very best of Maxwell engineering. The RC12 windlass range is suitable for boats ranging from 10m (30ft) to 20m (65ft) and has been designed and engineered to expertly balance aesthetics with rugged dependability. The deck plate, chain pipe cover, heavy-duty pressure arm, stripper arm, chain wheel, and fluted capstan drum are all manufactured using marine-grade (AISI 316) stainless steel, which is x-rayed by Maxwell QC to ensure the chemical composition of the metal. The through-deck hawse pipe ensures easy entry of the rope/chain rode into and out of the anchor locker, and the double cone-type brake/clutch mechanism permits ‘Free Fall’ anchoring. Cone clutches, unlike dog clutches, provide smooth progressive engagement, ensuring safe and precise operator control. Emergency manual retrieval is made simple and easy with Maxwell’s unique "Active Latch Ratchet System" operation that prevents the backwind of the windlass during manual hauling of the anchor. Features: Activation of the ratcheted mechanism lever ensures the windlass cannot backwind during emergency (manual) retrieval of the rode (rope and/or chain) and anchor The Gearbox Used on the RC12 Provides Several Advantages, Including: Fast and easy windlass installation More corrosion resistant Easy to maintain and service Takes up less room in the anchor locker 75:1 ratio, single stage design with fewer moving parts, for smoother and quieter operation Allows for multi-positioning of the gearbox/motor Specifications: Maximum Pull: 2500 lbs. (1134 kg) Static Hold: 4840 lbs. (2200 kg) Chain Size: 3/8 in. (10/11 mm) Rope Size (Nylon): 5/8 in. – 3/4 in. (16 mm – 20 mm) Chain Speed (at normal working load): 79 ft/min (24 m/min) Rope Speed (at normal working load): 65 ft/min (20 m/min) Power Supply (DC): 12 VDC          Motor (Watt): 1200 W   Net Weight:  lbs (32 kg) Hydraulic Pressure: 2000 PSI (138 Bar) Hydraulic Flow: 11 USgal/min (40 l/min) Net Weight (Hydraulic): 71 lbs (32 kg) Important: Maxwell windlasses must be used in conjunction with a chain stopper and/or alternative snubbing device to take the load off the windlass while laying at anchor. The chain stopper and alternative snubbing system should also be used to secure the anchor in the fully raised position while underway. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RC12/10 12V Windlass The RC12 fully automatic windlass series is designed to effortlessly retrieve and deploy 10mm (3/8") short link chain and 16mm (5/8") to 20mm (3/4") three strand or 8-Plait rope (RC12-10) and 12mm/13mm (1/2") short link chain and 20mm (3/4") three strand or 8-Plait rope (RC12-12). With a maximum pull of 1590 kg (3500 lb), and an anchor retrieval rate of 15m/min (50ft/min), the RC12-12 is one of the fastest and gruntiest windlasses in its class. A sleek, Low Profile version and a fluted stainless steel capstan drum version, are available. The RC12 is packed with innovative features combined with Maxwell's traditionally classic aesthetics, but reflecting the modern form follows function of the highly successful RC6, RC8 and RC10 series windlasses. The elegantly designed deckplate and chainpipe cover are manufactured in polished marine-grade 316 stainless steel, as are the heavy duty pressure arm, stripper, chainwheel and fluted capstan drum. The huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker. Double cone-type brake/clutch mechanism permits Free Fall anchoring. Cone clutches, unlike dog clutches, provide smooth progressive engagement, ensuring safe and precise operator control. The RC12 features Maxwell's revolutionary and Wave Design™ chainwheel. Emergency manual retrieval is made simple and easy with Maxwell's unique Active Latch Ratchet System operation that prevents backwind of the windlass during manual hauling of the anchor. The Maxwell-designed and innovative black, hard anodized gearbox provides numerous advantages: - Fast and easy windlass installation - More corrosion resistant - Easy to maintain and service - Takes up less room in the anchor locker - 75:1 Ratio (RC12-10) or 100:1 Ratio (RC12-12), single stage design with less moving parts, for smoother and quieter operation - Allows for multi-positioning of the gearbox/motor. Every Maxwell automatic rope/chain windlass comes complete with all the necessary components for fully automatic dual direction control in a competitively priced package.

RC12/10 Capstan Windlass - 24V - 3/8" Chain & 3/4" Rope The RC12 fully automatic windlass series is designed to effortlessly retrieve and deploy 10mm (3/8") short link chain and 16mm (5/8") to 20mm (3/4") three strand or 8-Plait rope (RC12-10) and 12mm/13mm (1/2") short link chain and 20mm (3/4") three strand or 8-Plait rope (RC12-12). With a maximum pull of 1590 kg (3500 lb), and an anchor retrieval rate of 15m/min (50ft/min), the RC12-12 is one of the fastest and gruntiest windlasses in its class. A sleek, Low Profile version and a fluted stainless steel capstan drum version, are available. The RC12 is packed with innovative features combined with Maxwell's traditionally classic aesthetics, but reflecting the modern form follows function of the highly successful RC6, RC8 and RC10 series windlasses. The elegantly designed deckplate and chainpipe cover are manufactured in polished marine-grade 316 stainless steel, as are the heavy duty pressure arm, stripper, chainwheel and fluted capstan drum. The huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker. Double cone-type brake/clutch mechanism permits Free Fall anchoring. Cone clutches, unlike dog clutches, provide smooth progressive engagement, ensuring safe and precise operator control. The RC12 features Maxwell's revolutionary and Wave Design™ chainwheel. Emergency manual retrieval is made simple and easy with Maxwell's unique Active Latch Ratchet System operation that prevents backwind of the windlass during manual hauling of the anchor. The Maxwell-designed and innovative black, hard anodized gearbox provides numerous advantages: - Fast and easy windlass installation - More corrosion resistant - Easy to maintain and service - Takes up less room in the anchor locker - 75:1 Ratio (RC12-10) or 100:1 Ratio (RC12-12), single stage design with less moving parts, for smoother and quieter operation - Allows for multi-positioning of the gearbox/motor. Every Maxwell automatic rope/chain windlass comes complete with all the necessary components for fully automatic dual direction control in a competitively priced package. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RC10/10 24V Capstan Windlass for 3/8" Chain & 5/8" Rope The combined stainless steel and chromed bronze RC10 fully automatic windlass series is designed to effortlessly retrieve and deploy 8mm (5/16_) and 10mm (3/8") short link chain and 14mm and 16mm (5/8") three strand or 8-brait (plait) rope. Features: A sleek, Low Profile version and a fluted stainless steel capstan drum version, are available Simple two piece installation saves time and money and allows easy retrofitting without disassembly of the windlass Unique spacer tube design allows installation through virtually any deck thickness and the multiple mounting positions and self aligning gearbox ensure optimal location of gearbox and motor in virtually all installation situations Full disassembly capability of the topworks utilising only the handle provided and an Allen key The RC10 is manufactured from marine-grade 316 stainless steel and chromed bronze for long term durability The heavy duty stainless steel pressure arm, coupled with the unique rope/chain gypsy, is designed to effectively grasp the splice between rope and chain, giving the RC10 an unparalleled level of performance In combination with a heavy duty, large wire diameter, stainless steel pre-loaded spring, the pressure arm pivots on a trouble free bearing, thereby exerting maximum control pressure on the rode and splice The RC10 works just as effectively with all chain rodes for those who desire a Low Profile, elegantly styled windlass on their foredeck Huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker Cone type clutch/brake mechanism permits manual, Free Fall anchoring Sealed oil bath and marine-grade hard anodised, alloy gearbox provides maximum output via a precision worm and worm wheel This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RC12/10 12V Capstan Windlass The RC12 fully automatic windlass series is designed to effortlessly retrieve and deploy 10mm (3/8") short link chain and 16mm (5/8") to 20mm (3/4") three strand or 8-Plait rope (RC12-10) and 12mm/13mm (1/2") short link chain and 20mm (3/4") three strand or 8-Plait rope (RC12-12). With a maximum pull of 1590 kg (3500 lb), and an anchor retrieval rate of 15m/min (50ft/min), the RC12-12 is one of the fastest and gruntiest windlasses in its class. A sleek, Low Profile version and a fluted stainless steel capstan drum version, are available. The RC12 is packed with innovative features combined with Maxwell's traditionally classic aesthetics, but reflecting the modern form follows function of the highly successful RC6, RC8 and RC10 series windlasses. The elegantly designed deckplate and chainpipe cover are manufactured in polished marine-grade 316 stainless steel, as are the heavy duty pressure arm, stripper, chainwheel and fluted capstan drum. The huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker. Double cone-type brake/clutch mechanism permits Free Fall anchoring. Cone clutches, unlike dog clutches, provide smooth progressive engagement, ensuring safe and precise operator control. The RC12 features Maxwell's revolutionary and Wave Design™ chainwheel. Emergency manual retrieval is made simple and easy with Maxwell's unique Active Latch Ratchet System operation that prevents backwind of the windlass during manual hauling of the anchor. The Maxwell-designed and innovative black, hard anodized gearbox provides numerous advantages: - Fast and easy windlass installation - More corrosion resistant - Easy to maintain and service - Takes up less room in the anchor locker - 75:1 Ratio (RC12-10) or 100:1 Ratio (RC12-12), single stage design with less moving parts, for smoother and quieter operation - Allows for multi-positioning of the gearbox/motor. Every Maxwell automatic rope/chain windlass comes complete with all the necessary components for fully automatic dual direction control in a competitively priced package.

HRC10 Horizontal Rope Chain Windlass - 12V No Capstan 3/8" Chain, 5/8" Rope Maxwell's HRC10 represents yet another breakthrough in performance and anchor handling excellence. The horizontal, fully automatic rope/chain windlass has been designed to meet the demands for use on larger vessels up to 16 meters (52'), which require a completely above deck installation system. The HRC10 handles 5/8" rope and 3/8" chain, including the thick rope to chain splice. The modern appearance of the HRC10 retains the classic good looks of previous Maxwell horizontal windlasses, while incorporating design features years ahead of its competitors. The HRC10 windlass is fitted with Maxwell's unique Wave Design™ chainwheel. The rope/chain wheel incorporates two unique design concepts that greatly improve the handling and control of the rope/chain spliced rode. The outer ribs of the chainwheel are angled slightly forward ensuring that the rope and the chain are smoothly guided in the wheel during anchor retrieval. As the rope pulls into the wheel, the opposite facing inner ribs grip the rope in an undulating manner, securing the rope more firmly in a 'wave pattern' action that is far superior to the traditional 'jam cleat' manner of holding the rope. Not only does this Wave Design™ hold the rope more securely, it is also kinder on the rope resulting in increased longevity of your anchor rode. Features: Aesthetically pleasing above deck design, evolved from the philosophy of form follows function, encapsulates the motor and drive in a two part watertight case, saving space below deck 2-part case consists of a die cast, marine-grade hard anodised alloy front section and a rugged and easily removable composite motor cover aft section 2-piece watertight case allows for quick and easy, on-deck, routine maintenance Simple "bolt down" installation ensures effortless and rapid on-deck installation and set up Stainless steel pressure arm always exerts maximum control pressure on the rode (rope, splice or chain) Wave Design™ chainwheel is able to accommodate a wide range of chain pitch differences, within the specified chain size diameters Unique Maxwell "wrap around"™ horizontal chainwheel ensures that more than 90° of the wheel is used, allowing greatly improved rope and chain handling compared with competitor designs The HRC10 works just as effectively with all-chain rodes for those who desire the added security and holding power of an all-chain anchor system The integral chain pipe and huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker Cone type clutch/brake mechanism permits manual, "free fall"™ anchoring and emergency crank recovery of the rode and anchor if required = The sealed oil bath and marine-grade hard anodised, alloy gearbox provides high efficiency output drive via precision worm and wormwheel This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Kit Liberty Stripper Assembly - 10mm - 3/8" Chain Features: Maxwell Marine Replacement Windlass Stripper Applications: Maxwell Liberty 2500 Windlass Chainwheel: 3/8" Includes Screw

HRC10 Horizontal Rope Chain Windlass - 12V Capstan 3/8" Chain, 5/8" Rope Maxwell's HRC10 represents yet another breakthrough in performance and anchor handling excellence. The horizontal, fully automatic rope/chain windlasses has been designed to meet the demands for use on larger vessels up to 16 meters (52'), which require a completely above deck installation system. The HRC10 handles 5/8" rope and 3/8" chain, including the thick rope to chain splice. The modern appearance of the HRC10 retains the classic good looks of previous Maxwell horizontal windlasses, while incorporating design features years ahead of its competitors. The HRC10 windlass is fitted with Maxwell's unique Wave Design™ chainwheel. The rope/chain wheel incorporates two unique design concepts that greatly improve the handling and control of the rope/chain spliced rode. The outer ribs of the chainwheel are angled slightly forward ensuring that the rope and the chain are smoothly guided in the wheel during anchor retrieval. As the rope pulls into the wheel, the opposite facing inner ribs grip the rope in an undulating manner, securing the rope more firmly in a 'wave pattern' action that is far superior to the traditional 'jam cleat' manner of holding the rope. Not only does this Wave Design™ hold the rope more securely, it is also kinder on the rope resulting in increased longevity of your anchor rode. Features: Aesthetically pleasing above deck design, evolved from the philosophy of form follows function, encapsulates the motor and drive in a two part watertight case, saving space below deck 2-part case consists of a die cast, marine-grade hard anodised alloy front section and a rugged and easily removable composite motor cover aft section 2-piece watertight case allows for quick and easy, on-deck, routine maintenance Simple "bolt down" installation ensures effortless and rapid on-deck installation and set up Stainless steel pressure arm always exerts maximum control pressure on the rode (rope, splice or chain) Wave Design™ chainwheel is able to accommodate a wide range of chain pitch differences, within the specified chain size diameters, suitable for use with the HRC10 Unique Maxwell "wrap around"™ horizontal chainwheel ensures that more than 90° of the wheel is used, allowing greatly improved rope and chain handling compared with competitor designs Works just as effectively with all-chain rodes for those who desire the added security and holding power of an all-chain anchor system The integral chain pipe and huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker Cone type clutch/brake mechanism permits manual, "free fall"™ anchoring and emergency crank recovery of the rode and anchor if required The sealed oil bath and marine-grade hard anodised, alloy gearbox provides high efficiency output drive via precision worm and wormwheel This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RC10-10 Capstan Windlass 12V - 3/8" Chain & 5/8" Rope The combined stainless steel and chromed bronze RC10 fully automatic windlass series is designed to effortlessly retrieve and deploy 8mm (5/16") and 10mm (3/8") short link chain and 14mm and 16mm (5/8") three strand or 8-brait (plait) rope. A sleek, Low Profile version and a fluted stainless steel capstan drum version, are available. Simple two piece installation saves time and money and allows easy retrofitting without disassembly of the windlass. Unique spacer tube design allows installation through virtually any deck thickness and the multiple mounting positions and self aligning gearbox ensure optimal location of gearbox and motor in virtually all installation situations. Full disassembly capability of the topworks utilising only the handle provided and an Allen key. The RC10 is manufactured from marine-grade 316 stainless steel and chromed bronze for long term durability. The heavy duty stainless steel pressure arm, coupled with the unique rope/chain gypsy, is designed to effectively grasp the splice between rope and chain, giving the RC10 an unparalleled level of performance. In combination with a heavy duty, large wire diameter, stainless steel pre-loaded spring, the pressure arm pivots on a trouble free bearing, thereby exerting maximum control pressure on the rode and splice. The RC10 works just as effectively with all chain rodes for those who desire a Low Profile, elegantly styled windlass on their foredeck. Huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker. Cone type clutch/brake mechanism permits manual, Free Fall anchoring. Sealed oil bath and marine-grade hard anodized, alloy gearbox provides maximum output via a precision worm and worm wheel. Features: Huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker. Cone type clutch/brake mechanism permits manual, Free Fall anchoring. Sealed oil bath and marine-grade hard anodised, alloy gearbox provides maximum output via a precision worm and worm wheel. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RC8 12V Windlass - 100W 5/16" Chain to 5/8" Rope Features: The stainless steel RC8-6 fully automatic rope/chain windlass is designed to effortlessly retrieve and deploy 6mm/7mm (1/4") chain spliced to 12mm (1/2") three strand or 8-brait (plait) rope. The larger stainless steel RC88 can be used with 8mm (5/16") chain spliced to 14mm (9/16") three strand or 8-plait rope. The ingeniously designed rope/chain gypsy (chainwheel) is able to accommodate a wide range of chain pitch differences within the specified chain size diameters suitable for use with the RC8 Series. A sleek, Low Profile version and a MAX-grip capstan drum version, with drum made in chromed bronze, are available. Simple two piece installation saves time and money and allows easy retrofitting without disassembly of the windlass. Unique spacer tube design allows installation through virtually any deck thickness and the multiple mounting positions and self aligning gearbox ensure optimal location of gearbox and motor in virtually all installation situations. The RC8 features Maxwell's revolutionary, and patented, new Wave Design chainwheel. The heavy duty stainless steel pressure arm is designed to effectively help grasp the rope/chain splice, giving the RC8 an unparalleled level of performance. In combination with a heavy duty, large wire diameter, stainless steel pre-loaded spring, the pressure arm always exerts maximum control pressure. The RC8 works just as effectively with all-chain rodes. Huge, through deck hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker. Full disassembly capability of the topworks utilising only the handle provided and an Allen key. Manual override and Free Fall, using the emergency crank/clutch handle provided. Sealed oil bath and marine-grade hard anodized, alloy gearbox provides maximum output via a precision worm and worm wheel.

RC10 Automatic Rope/Chain Windlass Designed for 3/8" chain and 5/8" rope combination Maximum Pull: 1870lbs. Metric chain size: 10mm Motor Wattage: 1200W Innovative heavy duty stainless steel pressure arm, coupled with a unique rope/chain gypsy, giving an unparalleled level of performance. Simple two piece installation, saving time and money and allowing easy retrofitting without disassembly of the windlass. Manufactured from marine grade chromed bronze for long term durability The topworks can be fully disassembled utilizing the handle provided, a screw driver and common allen key, making regular service and maintenance a breeze. No special tools required! A huge, through deck, hawse pipe throat ensures easy entry of the rope/chain rode into and out of the anchor locker Not only does the RC10 effortlessly handle combination rope/chain rodes, it works just as well with all chain rodes for those who may want the extra security of an all chain systems combined with an elegantly styled, low profile windlass on their foredeck. Exclusive Maxwell 3 Year Limited Warranty ensuring your confidence that you are getting the best product on the market. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Levered Chain Stopper f/3/8" or 10mm Chain Chain stoppers hold the chain and take the load off the windlass. They are used to set and ride on the anchor, break free the anchor or to prevent accidental free fall of the anchor while under way. Also recommended for VW series rope and chain systems to hold the chain while changing over from rope to chain. 10mm (3/8"): B - 86mm (3-7/16") C - 20mm (7/8") F - 190mm (7-1/2") G - 130mm (5-1/8") G1 - 30mm (1-3/16") I - 86mm (3-1/2") J - 44mm (1-3/4") J1 - 10mm (7/16") K - 64mm (2-5/8") L - 95mm (3-3/4") M - M10

Anchor Rode - 20'-3/8" Chain to 200'-5/8" Nylon Brait 20' of 3/8" HT spliced chain to 200' of 5/8" Nylon Brait rope Nylon Brait™ is an 8-strand nylon rope created through braid technology that yields a product with a firm strand formation yet full stowage flexibility. The unique construction offers maximum strength and energy absorption, and working windlass grip-hold. Applications: Docklines and anchorlines Construction: 8-strand Nylon Specific Gravity: 1.14

Anchor Rode - 25'-3/8" Chain to 250'-5/8" Nylon Brait 25' of 3/8" HT spliced chain to 250' of 5/8" Nylon Brait rope Nylon Brait™ is an 8-strand nylon rope created through braid technology that yields a product with a firm strand formation yet full stowage flexibility. The unique construction offers maximum strength and energy absorption, and working windlass grip-hold. Applications: Docklines and anchorlines Construction: 8-strand Nylon Specific Gravity: 1.14

Pressure Arm Upper 3/8" Chain Maxwell Pressure Arm Liberty 2500 3/8" Chain