|
RAM® Drill-Down Heavy Duty Mount for weBoost
This weBoost mounting kit includes a 3/8"-24 X .375" threaded RAM® Tough-Ball™ that screws directly into the weBoost antenna, a C size medium length socket arm, and a C size RAM® Diamond Ball base for flat surface drill-down mounting such as a rear bumper, spare tire carrier, or antenna bracket. The adjustability of the RAM® Mounts system allows you to collapse the antenna while not in use, as well as extend the reach of the weBoost antenna is mounted in a tight space. This weBoost antenna mount is compatible with all weBoost vehicle antennas including the Drive Reach OTR, RV, and Drive X RV antennas making this the ideal mounting solution for off-road vehicles and semi-trucks.
Features:
Kit includes 3/8"-24 X .375" Threaded RAM® Tough-Ball™ that screws into thread adapter of the weBoost antenna, C size medium length socket arm, and C size RAM® Diamond Ball base for flat surface drill-down mounting such as a rear bumper, spare tire carrier, or antenna brackets
The adjustability of the ball and socket technology allows the weBoost mount to collapse when not in use, and provide extended reach in tight mounting areas
Made of powder-coated, marine-grade aluminum for durability and reliability in the most demanding environments
Backed by a lifetime warranty
Specifications:
HOLE PATTERN: 2-Hole AMPS 1.912"
THREAD PITCH: 3/8"-24 X .375"
PLATE SIZE: 2.43" x 1.31"
BALL/SOCKET SIZE: C Size (1.5")
WEIGHT CAPACITY: Standard Use: 4 lbs, Heavy-Duty Use: 3 lbs
MATERIALS: Marine-grade aluminum, High strength composite
|
45.50 |
|
|
RAM Mount POD I No-Drill Vehicle Mount w/X-Grip II
Part #: RAM-B-316-1-UN8U
Consists of the universal spring loaded X-Grip II holder and RAM POD I universal No-Drill vehicle mount. The base of the mount clamps to your seat rail without any drilling necessary. Connected to the base is a 18" rigid flexible rod that can be bent to position your device to it's optimum viewing location. The RAM POD I will hold everything you need safely and securely.
X-Grip II consists of a spring loaded holder and 1" rubber ball connected to the back of the base. Included are extra easy access grip knobs, located on the back of the holder for quick release of your tablet. It expands and contracts for perfect fit of most 7" tablets. Please verify dimensions of your tablet below for compatibility with the X-Grip II.
Compatible Devices:
Amazon Kindle
Archos 7
Asus EEE Pad Memo
Barnes & Noble NOOKcolor
BlackBerry PlayBook
Dell Streak 7
HTC Flyer
Samsung Galaxy Tab (7" version)
Holder Dimensions:
Minimum Width = 2.25"
(Devices 2.25" in width must be a minimum of 7" in height to fit)
Maximum Width = 5.75"
Depth = 0.875"
Features:
1. Spring loaded holder expands and contracts for perfect fit of your tablet
2. Rubber coated tips will hold your tablet firm and stable
3. Versatility of holder allows for attachment to many RAM-to-RAM ball and 1" socket mounts
4. Socket technology allows for multiple adjustment angles and articulation of your tablet
5. Easy access grip knobs, located on the back of the holder for quick release of your tablet
Material:
High Strength Composite, Rubber Tips and Powder Coated Marine Grade Aluminum
|
89.26 |
|
|
Ram Mounts
Looking for all the Ram Mount products we carry them. You can find them all right here in our Ram Mount Store Aqua Box Mount section. With everything from camera mounts to vehicle mounts including cell phone mounts, you will have plenty of choices to consider and options to choose from. Ram Mounting Systems is a quality manufacturer of all kinds of different mounts for your watercraft. You can get cell phone mounts and drink cup mounts here, along with GPS mounts and fishing rod holders. There are even iPad/iPhone/iPod mounts so you do not have to worry about having your electronics safe but close at hand.
If you have a kayak we have kayak mounts, too, and you can even do some work or surf the internet with laptop mounts to choose from. Of course, you want to make sure you choose a good marine electronics mount for your equipment, so you do not risk losing anything vital. Tablet mounts, swing arm mounts, surface mounts, and suction cup mounts are all available, and we have seat mounts, as well. You can even choose from motorcycle mounts, and rail/handle bar mounts to ensure you have everything you need your all of your future adventures.
|
|
|
ATLAS™ 10" Hydraulic Jack Plate Heavy-Duty for Verado - Black
T-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp.
5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE
ATLAS™ is truly the best hydraulic jack plate in the world
ATLAS™ is factory installed by more boat manufacturers than any other plate
ATLAS™ is used by more professional fisherman than any other hydraulic jack plate
ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets
ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China
6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER
ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied
ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied
ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that
ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure
ATLAS™ was the first plate to offer a very simple actuator replacement in the field
ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
1983.30 |
|
|
Vision Series Mount - 6" Aft Angled - Heavy Duty for Open Array Radars
The Vision Series Mounting System is a revolutionary design that provides the simplest, most attractive solution to your electronics mounting requirements.
Features:
All-new sleek, modern design
First all modular system - extremely versatile
Simple selection and installation
Easy to add accessories
Powder coated aluminum
Requires Vision Mounting Plate to install radar or sat dome antenna
6" Heavy Duty Aft Mount
6" Tall
Aft raked 30 degrees
|
432.00 |
|
|
RAM® Track Ball™ Heavy Duty Mount for weBoost
This weBoost mounting kit includes a 3/8"-24 X .375" threaded RAM® Tough-Ball™ that screws directly into the weBoost antenna, a C size medium length socket arm, and a C size RAM® Track Ball™ to mount to a third party track system or any RAM® Tough-Track™ system. The adjustability of the RAM® Mounts system allows you to collapse the antenna while not in use, as well as extend the reach of the weBoost antenna is mounted in a tight space. This weBoost antenna mount is compatible with all weBoost vehicle antennas including the Drive Reach OTR, RV, and Drive X RV antennas making this the ideal mounting solution for off-road vehicles and semi-trucks.
Features:
Kit includes 3/8"-24 X .375" Threaded RAM® Tough-Ball™ that screws into thread adapter of the weBoost antenna, C size medium length socket arm, and C size RAM® Track Ball™ to mount to a third party track system or any RAM® Tough-Track™ system
The adjustability of the ball and socket technology allows the weBoost mount to collapse when not in use, and provide extended reach in tight mounting areas
Made of powder-coated, marine-grade aluminum for durability and reliability in the most demanding environments
Backed by a lifetime warranty
Specifications:
HARDWARE INCLUDED: (1) Friction Washer, (1) 1/4"-20 x 7/8" T-Bolt,
T-BOLT DIMENSIONS: .48" x .95"
THREAD PITCH: 3/8"-24 X .375"
BALL/SOCKET SIZE: C Size (1.5")
WEIGHT CAPACITY: Standard Use: 4 lbs, Heavy-Duty Use: 3 lbs
MATERIALS: Marine-grade aluminum, High strength composite
|
48.73 |
|
|
RAM® Tough-Claw™ Heavy Duty Mount for weBoost
This weBoost mounting kit includes a 3/8"-24 X .375" threaded RAM® Tough-Ball™ that screws directly into the weBoost antenna, a C size medium length socket arm, and a C size medium clamp RAM® Tough-Claw™ to mount to 1" to 1.875" rails and bars such as a vehicle ladder, or roof/bed rack. The adjustability of the RAM® Mounts system allows you to collapse the antenna while not in use, as well as extend the reach of the weBoost antenna is mounted in a tight space. This weBoost antenna mount is compatible with all weBoost vehicle antennas including the Drive Reach OTR, RV, and Drive X RV antennas making this the ideal mounting solution for off-road vehicles and semi-trucks.
Features:
Kit includes 3/8"-24 X .375" Threaded RAM® Tough-Ball™ that screws into thread adapter of the weBoost antenna, C size medium length socket arm, and C size medium clamp RAM® Tough-Claw™ to mount to 1" to 1.875" rails and bars such as a vehicle ladder or roof/bed rack
The adjustability of the ball and socket technology allows the weBoost mount to collapse when not in use, and provide extended reach in tight mounting areas
Made of powder-coated, marine-grade aluminum for durability and reliability in the most demanding environments
Backed by a lifetime warranty
Specifications:
CLAMP RANGE: 1" - 1.875" diameter, 0" - 1.6" flat surfaces
THREAD PITCH: 3/8"-24 X .375"
BALL/SOCKET SIZE: C Size (1.5")
WEIGHT CAPACITY: Standard Use: 4 lbs, Heavy-Duty Use: 3 lbs
MATERIALS: Marine-grade aluminum, High strength composite
|
72.07 |
|
|
Vehicle Base
Compatible Vehicles:
DODGE RAM 1500-5500 (2008-2011)
This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation
Placement of Mount:
Passenger side, front, where seat rail frame attaches to floor board.
DRILLING REQUIREMENTS:
No - attaches to seat studs
Seat Configuration:
Bucket
Pole:
Purchased Separately
Weight:
2.1 lbs.
Material:
Powder Coated Steel
Dimensions:
A = 14.75", B = 3.8", C = 1.75", Hole Center = 13.25"
Features:
Quick installation with no drilling needed. Rock solid construction with lifetime warranty. Low profile keeps mount away from passenger leg space. Won?t interfere with levers or factory-installed console or 4WD lever. Designed to accommodate trucks with PTO
Swing Arm
The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray.
The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12".
Material:
Powder Coated Marine Grade Aluminum
Ball Size:
1.5" Rubber Ball "C" Size
Note:
Part number reflects product packaged in clear clam shell for store shelf display.
Laptop Mount Tray
The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics.
Tough-Tray Dimensions:
Tray Depth: 10.0"
Tray Thickness: 2.125"
Tray Width (Expansion): 10" to 16"
Side Clamp Arm Height: 0.5" (min) to 1.75" (max)
Material:
High Strength Composite
Note:
Part number reflects product packaged in clear clam shell for store shelf display. The Tough-Tray is compatible with laptops that have 17" screens. If the Tough-Tray Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-n-Motion kit.
|
237.17 |
|
|
RAM® Drill-Down Mount for Apple MagSafe
This RAM® MagSafe Adapter is designed specifically to fit the official Apple MagSafe Charger with the added benefit of RAM® Mounts compatibility. This adapter allows a perfect and secure fit for the MagSafe's charging disk and is only compatible with the iPhone 12 and iPhone 13 series, with or without an official Apple MagSafe case. Included in this kit is the RAM® B size diamond ball base with 2-hole AMPS pattern and B size medium length socket arm, perfect for drill-down mounting in your vehicle. Take advantage of your iPhone 12's and iPhone 13's magnetic MagSafe charging abilities with this MagSafe mount.
Features:
MagSafe mount adapter designed specifically for MagSafe charging disk (not included)
Includes B size medium length socket arm and diamond ball base featuring universal AMPS hole pattern for drill-down mounting; ball and socket technology allows for near-infinite adjustability
Compatible with iPhone 12 and 13, Pro, Pro Max, and mini, with or without Apple MagSafe phone cases; not compatible with standard phone cases
Backed by a lifetime warranty
Specifications:
SOCKET-TO-SOCKET LENGTH: 3"
HOLE PATTERN: 2-Hole AMPS: 1.912"
BALL/SOCKET SIZE: B Size (1")
WEIGHT CAPACITY: Standard Use: 2 lbs, Heavy-Duty Use: 1 lb
MATERIALS: Marine-grade aluminum, High strength composite
WEIGHT: 0.52 lbs.
|
26.46 |
|
|
Drill-Down Dashboard Mount with Backing Plate - C Size Medium
Meet the new go-to mount and component option for pairing any holder or dock with a dashboard drill-down mount. The RAM-101-225B2U consists of a C-size medium-length double socket arm, two round 2.5" diameter round bases with the universal AMPS hole pattern, and one 2.10" x 2.60" steel backing plate (hardware included).
RAM®'s patented rubber ball and socket technology dampens shock and vibration and allows for near-infinite adjustment, enabling the perfect viewing and operating angle of your device.
Features:
Drill-down double ball mount with a 2.10 x 2.60 in. steel backing plate that connects to RAM® components containing the universal AMPS hole pattern
Includes a C-size 1.5 in. RAM® rubber ball and a medium-length double socket arm; ball and socket technology allows for near-infinite adjustability
Components made of powder-coated, marine-grade aluminum, and steel for durability and reliability in the most demanding environments
Backed by a lifetime warranty
Specifications:
Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Machine Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers
Product Dimensions (inch): Overall Height: 7.35"
Socket to Socket Length (inch): 4.66”
Hole Pattern: Round Plate:, 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter
Ball Size (inch): C size (1.5”)
Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs.
Materials: Marine-grade aluminum and steel
Weight: 1.4 lb.
|
53.16 |
|
|
Drill-Down Dashboard Mount with Backing Plate - C Size Short
Meet the new go-to mount and component option for pairing any holder or dock with a dashboard drill-down mount. This mount consists of a C-size short-length double socket arm, two round 2.5" diameter round bases with the universal AMPS hole pattern, and one 2.10 x 2.60 in. steel backing plate (hardware included). RAM®'s patented rubber ball and socket technology dampens shock and vibration and allows for near-infinite adjustment, enabling the perfect viewing and operating angle of your device.
Features:
Drill-down double ball mount with a 2.10 x 2.60 in. steel backing plate that connects to RAM® components containing the universal AMPS hole pattern
Includes a C-size 1.5" RAM® rubber ball and a short double socket arm; ball and socket technology allows for near-infinite adjustability
Components made of powder-coated, marine-grade aluminum, and steel for durability and reliability in the most demanding environments
Backed by a lifetime warranty
Specifications:
Hardware Included: (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Machine Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers
Product Dimensions (inch): Overall Height: 5.225"
Socket to Socket Length (inch): 2.5”
Hole Pattern: Round Plate:, 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter
Ball Size (inch): C size (1.5”)
Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs.
Materials: Marine-grade aluminum and steel
Weight: 1.16 lb.
|
51.46 |
|
|
RAM® Tough-Clip™ Paddle Cradle with Track and Drill-Down Mounting Hardware
The RAM Tough-Clip™ Paddle Cradle allows you to mount a paddle to your canoe, kayak or paddle board. With its universal design, the Tough-Clip™ will hold most paddles with a handle of 1”-1.31” in circumference. This kit includes hardware and instructions for both a drill-down installation option and a track mounting option that’s compatible with the RAM Tough-Track™.
Material:
High Strength Composite
Note:
Part number reflects product packaged in retail bag for store shelf display.
|
16.76 |
|
|
RAM® No-Drill™ Vehicle Base for '19 Chevy Silverado 1500 & GMC 1500
The RAM® No-Drill™ laptop mounting base features a stabilizer foot and heavy-duty steel base custom-designed to fit the 2019 Chevrolet All-New Silverado and GMC Next Generation Sierra perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the mounting base in the vehicle.
Specifications:
Placement of Mount: Passenger side, in front, where seat frame meets floor board
Drilling Requirements: No. Utilizes existing vehicle mounting points and hardware
Seat Configuration: Bucket
Pole: Purchase Separately
Material: Powder Coated Steel
Features:
Custom, No-Drill™ mounting base offers lowest profile in the industry
Manufactured from high strength steel with a durable powder coat finish
If required, high quality fastening hardware is included
Mounts using existing seat bolts, no drilling required
|
52.14 |
|
|
RAM® No-Drill™ Vehicle Base for 2019 Ford Ranger
The RAM® No-Drill™ laptop mounting base features a stabilizer foot and heavy-duty steel base custom-designed to fit the 2019 Ford Ranger perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the mounting base in the vehicle.
Specifications:
Placement of Mount: Passenger side, in front, where seat frame meets floor board
Drilling Requirements: No. Utilizes existing vehicle mounting points and hardware
Seat Configuration: Bucket
Pole: Purchased Separately
Material: Powder Coated Steel
Features:
Custom, No-Drill™ mounting base offers lowest profile in the industry
Manufactured from high strength steel with a durable powder coat finish
If required, high quality fastening hardware is included
Mounts using existing seat bolts, no drilling required
|
54.61 |
|
|
RAM® No-Drill™ Universal Mount f/Heavy Duty Trucks
The RAM® No-Drill™ mounting base features a heavy-duty steel mounting base custom designed to fit these vehicles perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the base in the vehicle. This configuration provides a telescoping feature that ranges from 12 to 18 inches. The double swing arm provides articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. This vehicle base kit comes with the 2.5” round plate with AMPs hole pattern for attaching to multiple RAM products.
Hole Pattern:
4-Hole AMPS: 1.181" x 1.496"
3-Hole 120-Degree: 1.812" Diameter
Materials:
Powder coated steel
Marine grade-aluminum
Ball/Socket Size:
C Size - 1.5"
|
262.36 |
|