Ram Mounts Looking for all the Ram Mount products we carry them. You can find them all right here in our Ram Mount Store Aqua Box Mount section. With everything from camera mounts to vehicle mounts including cell phone mounts, you will have plenty of choices to consider and options to choose from. Ram Mounting Systems is a quality manufacturer of all kinds of different mounts for your watercraft. You can get cell phone mounts and drink cup mounts here, along with GPS mounts and fishing rod holders. There are even iPad/iPhone/iPod mounts so you do not have to worry about having your electronics safe but close at hand.   If you have a kayak we have kayak mounts, too, and you can even do some work or surf the internet with laptop mounts to choose from. Of course, you want to make sure you choose a good marine electronics mount for your equipment, so you do not risk losing anything vital. Tablet mounts, swing arm mounts, surface mounts, and suction cup mounts are all available, and we have seat mounts, as well. You can even choose from motorcycle mounts, and rail/handle bar mounts to ensure you have everything you need your all of your future adventures.

RAM Sealed Enclosure Medium/Wide Size AQUA BOX® Aqua Box 6 Internal Dimensions: Width=4", Height=6", Depth=1.75" inches Aqua Box 6 External Dimensions: Width=5.25", Height=6.5", Depth=2" inches Features: 1. A unique, all inclusive seal and Flex-Lens. This is really cool stuff! 2. Touch through lens to operate buttons. 3. Power, earphone and accessory cables are routed through a self draining baffledesign to keep moisture out. 4. Fits any RAM Mounting System for use on Planes, Motorcycles, Boats, ATVs, Bikes, etc. 5. Easily locks with any standard mini padlock. 6. All marine grade construction including stainless steel hinge pin and mounting hardware. 7. Flex-Lens may be replaced in seconds if scratched or damaged. (inexpensive) 8. Lifetime Warranty on all components other than Flex-Lens. Installation Instructions: The face of the Aqua Box 6 is a door, allowing you to place your electronic device in the cradle. If required, you can lock the box, with a small padlock, once closed. Inside the RAM Aqua Box are padded sheets enabling you to place your electronic device in the box firmly and securely. You can punch out the back of the Aqua Box to allow cables you be connected to you device, while maintaining a waterproof environment. Important Note: Apple iPhone and iPod touch screens are not operable through the RAM Flex Lens while in the Aqua Box.

RAM Universal Medium Tough-Clamp with 1" Diameter Rubber Ball An extra pair of hands is something that almost everyone has wished for at some point. The RAM Tough-Clamp is the solution. This extremely versatile product from RAM has endless applications and will certainly become one of your most valued tools. The RAM Tough-Clamp includes a 1" ball which can be used to mount a variety of products utilizing RAM's vast selection of mounting solutions. Attach your GoPro Camera, Smartphone, RAM AQUA BOX Pro or similar light weight device on almost any flat surfaces and square rails. Clamping Dimensions: Flat surfaces and square rails from 0" to 1.75" thick Round rails from 0.75" to 1.125" OD Features: High strength glass filled nylon construction with corrosion resistant stainless steel hardware Swiveling jaw-end pads provide stable, even gripping and protection of mounting surface Clamp jaw is configured for round, flat and odd shapes 1" rubber ball is compatible with numerous RAM arms and mounts Small, sleek form factor that accommodates for small, tight spaces Built-in lanyard holes Quick engage and release of clamp Lifetime Warranty! Made in U.S.A. Material: High Strength Composite Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Combination Strap, Handlebar, Rail Mount with Double Socket Arm & Adapter Base for UTVs & ATVs Description The RAM-B-149Z-2U consists of a steel strap base, u-bolt bases, double socket arm and diamond adapter base. The diamond adapter base has a hole pattern that matches the industry standard AMPS hole pattern and will connect to a large variety of RAM Mount and third party cradles. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the double socket arm. With a twist of the arm knob, you can move the mount to your optimum viewing position. Designed for a clean installation, the RAM strap mount will accommodate most common roll bar sizes on UTV's, allowing for the placement of the RAM rubber ball base. This mount can also be attached to smaller diameter handlebars on ATVs using the included hardware. With the ball base in place, you have the foundation for mounting everything from GPS Devices, RAM Aqua Boxes, Spotlights and Radios. Rail Accommodation Dimensions: Mount with Strap: 1.57" to a maximum of 3.15" Mount with U-Bolt: 0.50" to a maximum of 1.25" Material: Powder Coated Marine Grade Aluminum

RAM ATV/UTV Strap Mount for the Garmin Astro 320, GPSMAP 62, 62s, 62sc, 62st & 62stc Description: The RAM-B-149Z-2-GA41U consists of a steel strap base, u-bolt bases, double socket, diamond adapter base and high strength composite cradle. Designed for a clean installation, the RAM strap mount will accommodate most common roll bar sizes on UTV's, allowing for the placement of the RAM rubber ball base. This mount can also be attached to smaller diameter handlebars on ATVs using the included hardware. With the ball base in place, you have the foundation for mounting everything from GPS Devices, RAM Aqua Boxes, Spotlights and Radios. The mount is designed with a RAM 1" diameter patented rubber ball and socket system that has adjustment points at both ends of the double socket arm; this allowing for almost infinite adjustment and perfect viewing angles. Rail Accommodation Dimensions: Mount with Strap: 1.57" to a maximum of 3.15" Mount with U-Bolt: 0.50" to a maximum of 1.25" Compatible Devices: Garmin Astro 320 Garmin GPSMAP 62 Garmin GPSMAP 62s Garmin GPSMAP 62sc Garmin GPSMAP 62st Garmin GPSMAP 62stc Material: High Strength Composite

PedestalPod with RAM Mount Pre-Cut for Lowrance HDS-9 Gen2 Touch, HDS-9 Gen3 & HDS Carbon 9 - Carbon Black PedestalPod with RAM Mounts is specifically designed for mounting the fishfinder near the bow on Bass Boats. Built on the foundation of NavPods popular range of waterproof housings for marine electronics, PedestalPods position your fishfinder/chartplotter at an easy to reach 20” off the deck. This allows the user easy access to the display for changes to range, zoom or even control the trolling motor. There is a big difference between reaching down to a height off the deck of 20” to control your fishfinder compared to reaching all the way down to the deck when it was only bracket mounted.  PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal. This offers protection of your fishfinder/chartplotter from the harshest of wet boating conditions.  This protection assures reliability and longevity of your marine electronics. PedestalPod with RAM Mounts utilizes the proven RAM Mounting system with the large 2.25” rubber “D” size ball and the RAM pin-lock security solution.  RAM Mounts are designed with a patented rubber ball and socket system that allows an almost infinite amount of ways to position the angle of the fishfinder for that precise position of viewing. When you might be trailering, or storing the boat, the display can fold flat onto the deck with only 10” of clearance.  This will allow most boat covers to fit over the PedestalPod when not in use. Your fishfinder is easily flush mounted into the pre-cut face of the NavPod. There are pre-cut models available for 7”, 9” and 12” LCD displays from all major marine electronic manufacturers. PedestalPods are waterproof housings for marine electronics specifically designed for bass boats. PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your marine electronics from the harshest of wet boating conditions. PedestalPods provide the convenience of height for accessibility and added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20” off the deck and located near the bow and at a 45-degree angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. All NavPods are manufactured with a double gasket system that provides an excellent watertight seal. They keep harsh spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the PedestalPod. The heavy duty, black powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look. It provides protection for wires and connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. All NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. PedestalPods are available pre-cut for 7”, 9” and 12” LCD displays from all major marine electronic manufacturers. Constructed out of durable ABS like all Gen3 NavPods, black carbon PedestalPods have the same high gloss finish with UV stability. NavPod backs up their commitment to quality by offering a 10-year warranty on all Gen3 NavPods. PedestalPods – Protection, Convenience, Security

Fishfinder Mount for Lowrance Hook2 Series - 1" Track Mount Designed for light duty fresh water use, this B size (1”) Track Ball™ kit for the Lowrance Hook² allows users to swap out the factory mounting solution with a RAM® Mounts solution. Simply attach the included adapter to the Lowrance Hook² and you’re ready to connect the double socket arm and base to virtually any track system including the RAM® Tough-Track™. Made of high strength composite and powder coated marine grade aluminum, this kit is designed to keep your Hook² secure and stable in rugged environments on your kayak or inflatable. T-Bolt Dimensions: .48" x .95" Material: High Strength Composite and Marine Grade Aluminum Ball Size: 1" Rubber Ball Size Note: Part number reflects product packaged in a retail bag store shelf display.

PedestalPod with RAM Mount Pre-Cut for Lowrance HDS-9 MFD Gen2 Touch & HDS-9 Gen3 - Carbon Black PedestalPod with RAM Mounts is specifically designed for mounting the fishfinder near the bow on Bass Boats.  Built on the foundation of NavPods popular range of waterproof housings for marine electronics, PedestalPods position your fishfinder/chartplotter at an easy-to-reach 20” off the deck. This allows the user easy access to the display for changes to range, zoom or even control the trolling motor. There is a big difference between reaching down to a height off the deck of 20” to control your fishfinder compared to reaching all the way down to the deck when it was only bracket mounted. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal. This offers protection of your fishfinder/chartplotter from the harshest of wet boating conditions.  This protection assures the reliability and longevity of your marine electronics. The PedestalPod with RAM Mounts utilizes the proven RAM Mounting system with the large 2.25” rubber “D” size ball and the RAM pin-lock security solution. RAM Mounts are designed with a patented rubber ball and socket system that allows an almost infinite amount of ways to position the angle of the fishfinder for that precise position of viewing. When you might be trailering, or storing the boat, the display can fold flat onto the deck with only 10” of clearance.  This will allow most boat covers to fit over the PedestalPod when not in use. Your fishfinder is easily flush mounted into the pre-cut face of the NavPod. There are pre-cut models available for 7”, 9”, and 12” LCD displays from all major marine electronic manufacturers. PedestalPods – Protection, Convenience, Security.

RAM® Vertical Drill-Down Laptop Mount The RAM Tough-Tray™ is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. The Tough-Tray™ is compatible with laptops that have 17" screens. Universal Multi-Function Vehicle Base: Truck fleets world wide will appreciate the well crafted universal multi-function vehicle base now offered by RAM. Considering the wide variety of seating arrangements in the commercial vehicle market, this new vehicle base is reversible by design. Now installers don’t have to choose between locating a flat surface or round tubing to attach to under the vehicle seat. RAM has you covered with either configuration. Tubing framed seats can be attached to in minutes using the supplied u-bolts. Once in place and safely secured, several hole patterns are available allowing the freedom to choose how best to create your custom mounting solution. Steel box frame seats need only four discrete holes drilled to secure the base. Using hardware chosen and supplied by the installer, secure the base where it’s most convenient. Using the supplied u-bolt hardware, attach any number of RAM pedestal mounts to create a mounting system unmatched in its versatility and stability. There simply is no substitute for RAM vehicle products. U-Bolt Dimensions: Accommodates rails from 0.625" to 1.5" in diameter. Included Hole Patterns: 100 x 100MM, 75 x 75MM, 50 x 100MM AMPS, RAM Three holes at 120 degrees Material: High Strength Composite and Powder Coated Marine Grade Aluminum

RAM Transducer Arm Mount with 18" Rigid Aluminum Rod and Open Single Socket: Compatible with all RAM 1" Ball Bases Kayak fishing is all about adaptability. RAM Mount offers the widest selection of kayak fishing accessories to adapt to a wide range of fishing scenarios. This transducer mount enables quick, effective deployment and retrieval of your Lowrance StructureScan LSS transducer, while protecting it from damage. Perfect for kayak applications, the included rigid mounting arm can quickly be retrieved if you enter shallow water or when beaching your kayak. With little effort, the transducer mount can quickly be moved to a different kayak with an existing 1" RAM ball. Add a RAM ball mount for the Lowrance HDS-7 Fishfinder, and you have a complete mounting solution for your next fishing adventure. Compatible Transducers: Lowrance StructureScan LSS-2 Lowrance StructureScan LSS-1 Features: 18" rigid aluminum rod can be bent to position your transducer to its optimum location Patented socket technology allows for quick raising, lowering, removal and stowage of transducer arm High quality materials prevent corrosion Compatible with the Yakattack 1" screw ball Lifetime warranty Made in U.S.A. Material: High Strength Composite and Aluminum Steel Ball Size: 1" Rubber Ball "B" Size Note: Part number reflects product packaged in clear clam shell for store shelf display. Transducer device not included with purchase.

RAM Mount Universal Finger Grip Holder Surface Mount Part #: RAM-B-138-UN4 Simply choose the base mounting hardware and the possibilities become endless with a RAM flat surface mount. Four mounting holes in the round ball base easily accommodate up to a #10 screw. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM's patented design also dampens shock and vibration helping to extend the life of your mobile device. Universal Finger Grip™ Holder Description: The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Transducer Arm Mount with Male Wedge Base and 1" Ball: Compatible with Hobie and Scotty Wedge Hole Bases Kayak fishing is all about adaptability. RAM Mount offers the widest selection of kayak fishing accessories to adapt to a wide range of fishing scenarios. RAM now offers a deployable transducer arm for kayaks. This solution enables the quick and effective deployment and retrieval of your transducer, while protecting your transducer from damage. Perfect for kayak applications, the transducer arm can quickly be retrieved if you enter shallow water or when beaching your kayak. With little effort, the arm can quickly be moved to a different kayak and attached to an existing flush mount or 1" RAM ball. The unique design provides a universal solution for virtually any kayak as well as any transducer. Compatible Transducers: The RAM transducer arm mount is compatible with all transducers that contain a 1/4" screw. Features: 1. 18" rigid aluminum rod can be bent to position your transducer to its optimum viewing location 2. Patented socket technology allows for quick raising, lowering, removal and stowage of transducer arm 3. Quality materials prevent corrosion and keeps your transducer arm mount 4. Compatible with Hobie and Scotty wedge bases 5. Lifetime warranty Material: High Strength Composite and Aluminum Steel Ball Size: 1" Rubber Ball "B" Size Note: Part number reflects product packaged in clear clam shell for store shelf display. Transducer device not included with purchase.

RAM Transducer Arm Mount with Open Single Socket: Compatible with all RAM 1" Ball Bases Kayak fishing is all about adaptability. RAM Mount offers the widest selection of kayak fishing accessories to adapt to a wide range of fishing scenarios. RAM now offers a deployable transducer arm for kayaks. This solution enables the quick and effective deployment and retrieval of your transducer, while protecting your transducer from damage. Perfect for kayak applications, the transducer arm can quickly be retrieved if you enter shallow water or when beaching your kayak. With little effort, the arm can quickly be moved to a different kayak and attached to a 1" RAM ball. The unique design provides a universal solution for virtually any kayak as well as any transducer. Compatible Transducers: The RAM transducer arm mount is compatible with all transducers that contain a 1/4" screw. Features: 1. 18" rigid aluminum rod can be bent to position your transducer to its optimum viewing location 2. Patented socket technology allows for quick raising, lowering, removal and stowage of transducer arm 3. Quality materials prevent corrosion and keeps your transducer arm mount 4. Lifetime warranty Material: High Strength Composite and Aluminum Steel Ball Size: 1" Rubber Ball "B" Size Note: Part number reflects product packaged in clear clam shell for store shelf display. Transducer device not included with purchase.

RAM 1" Ball Marine Electronic "LIGHT USE" Mount for the Garmin echo™ 100, 150 & 300c The RAM-B-101-G4 consists of a double socket arm, 2.5" diameter round base with the universal AMPS hole pattern and round adapter base that attaches directly to the back of the Garmin echo. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both socket ends of the arm; this with RAM's rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. Included is hardware that is used to attach the Garmin echo to the RAM Mount. This mount is compatible with the following electronic devices: Garmin echo 100 Garmin echo 150 Garmin echo 300c Ball Size: 1" Rubber "B" Ball Size Material: Powder Coated Marine Grade Aluminum Note: Part number reflects product packaged in clear clam shell for store shelf display.

Ram Pin-Lock™ Security Kit f/ 1" B Size Mounts and Gimbal Brackets You make a significant investment in the equipment you purchase to make your job or hobby easier or more enjoyable. Whether it's a high end piece of marine electronics, a GPS for your motorcycle, or a tablet used for business purposes, you need to protect your investment. RAM® Mounts protect your device from harmful shock and vibration, but what about theft and tampering? RAM® offers a full suite of security products which protect your device while mounted on your RAM® mount from theft and unwanted tampering. Simply add a security knob or nut to your RAM Mount to deter would-be thieves from targeting your equipment. RAM® security solutions are also a great way to add tamper resistance to your RAM® Mount in situations where there is a desire to prevent end-users from adjusting the mount or removing the device. High strength composite and brass construction assures a long life of trouble free use in a wide variety of environments including marine and salt water.