Shurflo 8020-513-236 Pump 115V 60Sw Pvs Shurflo- Diaphragm Pump 3 Chamber, 1.5 GPM Open Flow, 115VAC Intermittent Duty, 60 PSI Demand Switch (adjustable 40-60 PSI), Viton Valves, Santoprene Diaphragm, Polypropylene Housing, 3/8" NPT Female Ports, Has a Power Cord, UL/CSA Recognized, General Industrial Pump

Oberdorfer 935136C Pump Ss  

Raritan PHII PUMP Phii Pump Assy Complete

  Check all of your impellers contained within the engine cooling pumps, bilge pumps, ballast pumps, and so on.  One of the biggest contributors to impeller deterioration and damage is sitting idle in the same position for several months, so a proper check of the impeller(s) is vital to a reliable operation of the boat after storage and/or no operation.   Replacing an impeller is a fairly easy and straightforward process and one that you have probably done in the past. It is important to use the right tool to remove an impeller from the pump. Channel lock or needle-nose pliers are fine, but using an impeller removal tool is the best choice.  Never use a screwdriver to pry an impeller out of a pump; you could accidentally score the bronze housing which can lead to leaks.  Make sure you know how the impeller is being held in place.  Some are sealed to the shaft with an O-ring; others are held in place with a set screw and others with a c-clip.   Make sure to check the pump and the water lines for any trash or chunks of rubber that may have broken off from the impeller.  Even the smallest blockage can cause major engine cooling and overheating issues.  Also, remember to properly lubricate your new impeller with Vaseline or the lubricant included with the new impeller. This will reduce friction for a brand new impeller on a dry startup.   Most importantly, make sure you are using the right impeller for the application. We have seen many instances of people who have replaced an impeller with something that is close to the original, but not exactly right, and this can cause major problems for the engine once normal operation resumes.  You cannot match the size of the used impeller to a new one to determine the replacement, as a used impeller can be swollen and disfigured from its original specifications.  The best method is to obtain the impeller number off of the impeller itself, usually located on the edge of the shaft hole of the impeller, or obtain the part number of the pump, usually stamped into the bronze housing.   You can find just about every impeller that needs to be replaced at CLR Marine.  We carry Sherwood, Jabsco and Globe just to mention a few. We also carry many of the miner and major rebuild kits for many pumps.  A minor repair kit consists of the impeller and any gaskets or O-rings that may be needed to replace the impeller.  Our major rebuild kits include everything to rebuild that pump except for the shaft.  All kits are put together at time of order so you will always see the Quantity on Hand as 0.

Detroit Diesel 5196513 Gasket  

MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 15 Part #: MP21381 Size: 3 in. NPT Flow-Rate: 320 GPM Head Feet: 145   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

Jabsco 31800-0092 Series Industrial Diaphragm Pump Pump Body: Glass Filled Polypropylene, Four Piston, Diaphragm Pump Port Size: Snap-in 1/2" (13 mm) Hose Barb and 1/2" (13 mm) Straight Pipe Thread Flow: 4 GPM/15 LPM Pressure: Continuous, Maximum 40 psi (2.8 bar) at Ambient of 130° F (54.4° C). 31800 Series: No Switch 31801 Series: Cut-In 20 PSI, Cut-Out 40 PSI. Elastomers: Diaphragm: Santoprene Valves: Viton Motor: Permanent Magnet with Thermal Overload Protection. Continuous duty at 15 psi (1 bar) and 70°F (21°C) ambient temperature.     APPLICATIONS Self-Priming to 10 ft. (3 m) (wet) 5 ft. (1.5m) (dry). Runs Dry Without Damage. Smooth Flow. Snap-in Ports. Temperature: Liquid temperature range is 45°F to 130°F (7°C to 54°C). Viscosity: 250 cP maximum.   CONSTRUCTION – Water supply pump to the spray bars of road rollers and other compaction equipment, street sweepers, and truck mounted dust control systems. Superior equipment washdown results can be enjoyed with the 30801-Series pumps.   AGRICULTURAL – Supply pump for herbicide and pesticide sprayers and sprayboom equipment.   INDUSTRIAL – Fluid transfer applications for mild acids and bases. Chemical feed pump. Washing fluid supply pump in parts washing systems. Machine coolant pump. Concrete saw lubricant supply pump. Recirculating pump in filtering systems.   NOTE: Viton equipped models are not suitable for potable water applications.   Jabsco Industrial Diaphragm Pump 12Volt No Switch  

Jabsco 31801-0092 Series Industrial Diaphragm Pump Pump Body: Glass Filled Polypropylene, Four Piston, Diaphragm Pump Port Size: Snap-in 1/2" (13 mm) Hose Barb and 1/2" (13 mm) Straight Pipe Thread Flow: 4 GPM/15 LPM Pressure: Continuous, Maximum 40 psi (2.8 bar) at Ambient of 130° F (54.4° C). 31800 Series: No Switch 31801 Series: Cut-In 20 PSI, Cut-Out 40 PSI. Elastomers: Diaphragm: Santoprene Valves: Viton Motor: Permanent Magnet with Thermal Overload Protection. Continuous duty at 15 psi (1 bar) and 70°F (21°C) ambient temperature.     APPLICATIONS Self-Priming to 10 ft. (3 m) (wet) 5 ft. (1.5m) (dry). Runs Dry Without Damage. Smooth Flow. Snap-in Ports. Temperature: Liquid temperature range is 45°F to 130°F (7°C to 54°C). Viscosity: 250 cP maximum.   CONSTRUCTION – Water supply pump to the spray bars of road rollers and other compaction equipment, street sweepers, and truck mounted dust control systems. Superior equipment washdown results can be enjoyed with the 30801-Series pumps.   AGRICULTURAL – Supply pump for herbicide and pesticide sprayers and sprayboom equipment.   INDUSTRIAL – Fluid transfer applications for mild acids and bases. Chemical feed pump. Washing fluid supply pump in parts washing systems. Machine coolant pump. Concrete saw lubricant supply pump. Recirculating pump in filtering systems.   NOTE: Viton equipped models are not suitable for potable water applications.        

Primetime Hydraulic Pump This is a high performance self-priming 316 stainless steel centrifugal pump close coupled to a hydraulic motor.   The pump is ideal for Marine, Agricultural, and Industrial applications where suction lift is required.   The Primetime Hydraulic model features all 316 stainless steel components for superior corrosion resistance when pumping chemical compounds. A carbon/ceramic/viton bellows shaft seal is standard. Ports are ¾” NPT with a 1/8" NPT fill port. The check valve flapper design enhances the self-priming capability to 12 foot suction lift.   The hydraulic motor is designed with SAE #6 ports for the tank side while the pressure side has SAE # 4 ports. Maximum Pressure is 1000 PSI. Maximum Oil Flow is 3 GPM.   SPECIFICATIONS: Flow. . . . . . . . . . . . . . . . . . Up to 31 gpm Head . . . . . . . . . . . . . . . . . Up to 51’  Housing. . . . . . . . . . . . .... . 316 Stainless  Steel (Investment Cast) Cover . . . . . . . . . . . . . .... . 316 Stainless Steel (Investment Cast) Impeller . . . . . . . . . . .... . . 316 Stainless Steel Semi-Open (Sintered PM) Wear Plate . . . .  . . .. . ... . . 316 Stainless Steel Mechanical Seal . . . .. .. .. . . Carbon/Ceramic/Viton Bellows 150 PSI O-ring/Flapper . . . . .. ... . . . Viton Hydraulic Motor . . ... .. .. . . . Iron, Gerotor Type, .08 Cu. In. Displacement Weight . . . ... . . . . . . . ... . . 12 lbs.   APPLICATIONS • Marine • Agricultural • Industrial   PUMP CONSTRUCTION • 316 Stainless Steel Investment Cast   HYDRAULIC MOTOR SPECIFICATIONS • .08 cu. in displacement • Max. Oil Flow: 3 GPM • Max. Pressure: 1000 PSI   Hydraulic Motor Port Sizes: • SAE # 4 Pressure • SAE # 6 Tank   Pump Port Sizes: • 3/4” NPT • 1/8” NPT Fill Port

Jabsco 12210-0003 Pump 115V Motor Pump Body: Bronze Port Size: 3/8" NPT Internal Pipe Thread and Adaptors for 3/4" garden hose thread Flow: 3.4 GPM at 10ft Pressure: 17.4 PSI Max Impeller: Neoprene or Nitrile Shaft Seal: Lip Type Motor: 115 Volt AC Intermittent duty with Replaceable Brushes, Stainless Steel Shaft, 6' cord, three prong grounding plug   APPLICATIONS The 12210-Series Pumps are the most compact self-priming flexible impeller 115 Volt AC Utility Pumps Jabsco offers.   INDUSTRIAL: Transferring liquids. Velocity-mixing. Pumping coolants. Pumping waste water to sewer. Cellar, yard and sump drainage. Cooling Heliarc welding equipment.   MARINE: Washing down decks and docks. Water for ship's service supply. Pumping out crank-case oil.   FARMING: Pumping water for stock, poultry houses, farmhouse. Pumping water from wells and cisterns. Pumping liquid ballast into tractor tires. Pumping water from flooded basements.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, cesspools, sumps, etc. Draining water heaters and water closets. Draining laundry tubs below sewer level. Removing water trapped between walls, draining inaccessible places when pipes break or leak. Draining fishing ponds and garden pools. Removing sludge, lye water and other caustics from stopped up drains and sinks.   Jabsco Flexible Impeller Utility Pump 115V 3.4GPM Nitrile Impeller  

Primetime 115volt Pump The Primetime Pump is a high performance self-priming 316 stainless steel centrifugal pump. The pump is ideal for marine, industrial, agricultural or commercial applications where suction lift is required.   Primetime features all 316 stainless steel components for superior corrosion resistance when pumping sea water or chemical compounds.  A carbon / ceramic / Viton mechanical shaft seal is standard.  Ports are 3/4” NPT with a 1/8” NPT fill port. The Primetime model is capable of 12 foot suction lift (3450 rpm). Marine ignition protected motors (ISO 8846).   Applications Marine Pump used as a Fresh water pump, Air Conditioning pump, Refrigeration pump, RO pre pump, Gyroscope stabilization cooling, Agricultural pump, and Industrial pump.   SPECIFICATIONS: Flow………………………Up to 21 GPM Head Feet…………….Up to 23’ Housing……………….316 Stainless Steel (Investment Cast) Cover……………………316 Stainless Steel Impeller……………….316 Stainless Steel Semi-Open Wearplate……………316 Stainless Steel Mechanical Seal… Carbon / Ceramic / Viton Bellows O-ring/Flapper…….Viton Weight…………………18 lbs

Primetime Pump 12VDC The Primetime Pump is a high performance self-priming 316 stainless steel centrifugal pump. The pump is ideal for marine, industrial, agricultural or commercial applications where suction lift is required.   Primetime features all 316 stainless steel components for superior corrosion resistance when pumping sea water or chemical compounds. A carbon / ceramic / Viton mechanical shaft seal is standard. Ports are 3/4” NPT with a 1/8” NPT fill port. The Primetime model is capable of 12 foot suction lift (3450 rpm). Marine ignition protected motors (ISO 8846).   Applications: Marine Pump used for Fresh water pump, Air Conditioning pump, Refrigeration pump, RO pre pump, Gyroscope stabilization cooling Agricultural pump Industrial pump   SPECIFICATIONS: Flow: Up to 21 GPM Head Feet: Up to 23’ Housing: 316 Stainless Steel (Investment Cast) Cover: 316 Stainless Steel Impeller: 316 Stainless Steel Semi-Open Wearplate: 316 Stainless Steel Mechanical Seal: Carbon / Ceramic / Viton Bellows O-ring/Flapper: Viton Weight: 13 lbs Motor is painted White

Primetime Pump 24VDC The Primetime Pump is a high performance self-priming 316 stainless steel centrifugal pump. The pump is ideal for marine, industrial, agricultural or commercial applications where suction lift is required.   Primetime features all 316 stainless steel components for superior corrosion resistance when pumping sea water or chemical compounds. A carbon / ceramic / Viton mechanical shaft seal is standard. Ports are 3/4” NPT with a 1/8” NPT fill port. The Primetime model is capable of 12 foot suction lift (3450 rpm).   Applications Marine Pump used as a Fresh water pump, Air Conditioning pump, Refrigeration pump, or RO pre pump and it is Marine ignition protected motors (ISO 8846) Agricultural pump Industrial pump   SPECIFICATIONS: Flow Up to 21 GPM Head Feet Up to 23’ Housing 316 Stainless Steel (Investment Cast) Cover 316 Stainless Steel Impeller 316 Stainless Steel Semi-Open Wearplate 316 Stainless Steel Mechanical Seal Carbon / Ceramic / Viton Bellows O-ring Flapper Viton Weight 13 lbs Motor is painted White

MP Pumps 21383 FM 15 BRONZE PUMP MP Pumps 21383, FLOMAX 15 Self Priming Centrifugal Pump, Wet End Only FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators and Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   3" X 3" NPT Ports Capacity up to 320 GPM Total Head up to 145 feet Bronze construction 5.75 inch diameter impeller

AMT Pump MSV3-5-1P Multistage Mtr/Pmp 1Hp 115v Multi-Stage Booster Pump – MSV3-5-1P, 5-Stage, 115-208-230 Volts NEMA 56C, Dual Cycle 50 and 60 Hz, 1.0 HP, single phase, Totally Enclosed, Fan Cooled motor Recommended to operate at or below the Best Efficient Point which is at 16 GPM and a Max Total Head of 105 feet Cast Iron base and adapter 1 inch NPT cast iron flanges 304 series stainless steel components with Teflon wear rings EPDM-Tungsten Carbide Seal that is easy to remove and replace The AMT MSV3-5-1P is a non-self-priming/gravity feed, industrial pump with high pressure and low output.  This unit is more commonly referred to as a jockey pump and is often installed for water transfer uses where no suction lift is required such as boiler feed, condensate return, high pressure washdown, irrigation, booster service, and fire protection/sprinkler systems.  These pumps have NOT been investigated for use in drinking water systems.