Raritan PHII PUMP Phii Pump Assy Complete

Great gift for Father's day, get dad what he really wants! Learn how to brew beer at home even faster with a Homebrew Beer Pump, now 10% OFF!   Get Coupon Here     Buy your Homebrew Beer Pump Now!

  Check all of your impellers contained within the engine cooling pumps, bilge pumps, ballast pumps, and so on.  One of the biggest contributors to impeller deterioration and damage is sitting idle in the same position for several months, so a proper check of the impeller(s) is vital to a reliable operation of the boat after storage and/or no operation.   Replacing an impeller is a fairly easy and straightforward process and one that you have probably done in the past. It is important to use the right tool to remove an impeller from the pump. Channel lock or needle-nose pliers are fine, but using an impeller removal tool is the best choice.  Never use a screwdriver to pry an impeller out of a pump; you could accidentally score the bronze housing which can lead to leaks.  Make sure you know how the impeller is being held in place.  Some are sealed to the shaft with an O-ring; others are held in place with a set screw and others with a c-clip.   Make sure to check the pump and the water lines for any trash or chunks of rubber that may have broken off from the impeller.  Even the smallest blockage can cause major engine cooling and overheating issues.  Also, remember to properly lubricate your new impeller with Vaseline or the lubricant included with the new impeller. This will reduce friction for a brand new impeller on a dry startup.   Most importantly, make sure you are using the right impeller for the application. We have seen many instances of people who have replaced an impeller with something that is close to the original, but not exactly right, and this can cause major problems for the engine once normal operation resumes.  You cannot match the size of the used impeller to a new one to determine the replacement, as a used impeller can be swollen and disfigured from its original specifications.  The best method is to obtain the impeller number off of the impeller itself, usually located on the edge of the shaft hole of the impeller, or obtain the part number of the pump, usually stamped into the bronze housing.   You can find just about every impeller that needs to be replaced at CLR Marine.  We carry Sherwood, Jabsco and Globe just to mention a few. We also carry many of the miner and major rebuild kits for many pumps.  A minor repair kit consists of the impeller and any gaskets or O-rings that may be needed to replace the impeller.  Our major rebuild kits include everything to rebuild that pump except for the shaft.  All kits are put together at time of order so you will always see the Quantity on Hand as 0.

Flotec FP5162 Thermoplastic Sprinkler Pump 1 HP Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads. KEY FEATURES Superior performance at depths to water of 20' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor (dual voltage) Self-priming after pump housing is initially filled (Check Valve or Foot Valve required) WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1 MAXIMUM CAPACITY:  55 GPM FLOW at 10' LIFT and 30 PSI:  28 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  42 psi SUCTION PIPE SIZE:  1-1/2" NPT DISCHARGE PIPE SIZE:  1-1/2" NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP5172 Thermoplastic Sprinkler Pump 1.5 HP Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads. KEY FEATURES Superior performance at depths to water of 20' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor (dual voltage) Self-priming after pump housing is initially filled (Check Valve or Foot Valve required) 1 year limited warranty   BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1-1/2 MAXIMUM CAPACITY:  67 GPM FLOW at 10' LIFT and 30 PSI:  45 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  47 psi SUCTION PIPE SIZE:  1-1/2" NPT DISCHARGE PIPE SIZE:  1-1/2" NPT AMP DRAW (full load):  9.6 amps on 230v / 19.2 amps on 115v VOLTAGE:  230v / 115v , 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 25 amp for 115v MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)    

Flotec FP5182 Thermoplastic Sprinkler Pump 2 HP Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads. KEY FEATURES Superior performance at depths to water of 20' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install 230 volt motor (dual voltage) Self-priming after pump housing is initially filled (Check Valve or Foot Valve required) 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  2 MAXIMUM CAPACITY:  69 GPM FLOW AT 10' LIFT and 30 PSI:  45 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  50 psi SUCTION PIPE SIZE:  2" NPT DISCHARGE PIPE SIZE:  2" NPT AMP DRAW:  12 amps on 230v / 24 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 30 amp for 115v MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP5230 Cast Iron Sprinkler Pump 1 HP Powerful 1 HP cast iron sprinkler pump moves up to 45 gpm. Perfect for sprinkler systems or water transfer applications. FEATURES Superior performance at depths-to-water of 25' or less Ideal for larger sprinkler systems and water transfer Rugged cast iron construction Voltage-selectable to run on 115v or 230v 1 year limited warranty BODY CONSTRUCTION: Cast Iron HORSEPOWER: 1 MAXIMUM CAPACITY: 45 GPM FLOW at 10' LIFT and 30 PSI: 35 GPM MAX LIFT:  25' MAXIMUM PRESSURE: 50 psi SUCTION PIPE SIZE: 1-1/4" NPT DISCHARGE PIPE SIZE: 1" NPT AMP DRAW (full load): 8.8 amps on 230v / 16.6 amps on 115v VOLTAGE: 230v / 115v , 60 Hz RECOMMENDED BREAKER: 15 amp on 230v / 25 amp on 115v MAXIMUM WATER TEMPERATEURE: 140 F (60 C)

Simer 2825SS Portable Utility Transfer Sprinkler Pump, 1HP Simer Portable Utility Transfer Sprinkler Pump, Stainless Steel Housing, Self-Priming, 1HP 115Volt Continuous Duty Motor, up to 10 GPM, up to 83psi, 1” NPT Ports with Garden Hose Adapter, 6 Foot Power Cord, Carry Handle

Flotec Portable Utility Booster Pump Manages a variety of home applications including sprinkling, pressure boosting and dewatering. Can be used as a portable sprinkler pump Ideal for boosting pressure to wash cars, boats and farm equipment 115V air cooled motor and has a 1 year limited warranty    BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 HP MAXIMUM PRESSURE:  62 PSI MAXIMUM CAPACITY:  10.3 GPM FLOW at 10' SUCTION LIFT and 30 PSI:  5.1 GPM SWITCH TYPE:  No Switch (Manual Operation) SUCTION SIZE:  1" (ships with garden hose adapter) DISCHARGE SIZE:  1" (ships with garden hose adapter) MAXIMUM SOLIDS HANDLING SIZE:  .06" AMP DRAW (full load):  7 Amps CORD LENGTH:  6' w/ 3-prong grounded plug VOLTAGE:  115v AC, 60 Hz

March 809-PL-HS Magnetic Drive Beer Pump The March 809-PL-HS Home Brew Beer Pump is great for all your brewing needs. The March 809 PL HS hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include brewing, home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.   • Home Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries. • Maximum liquid temperature for the 809 and 815 series is 250 F. • Port configurations include in-line and center inlet with side discharge. • Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic. • There are many motor options available Including AC, DC and High Speed versions for added flow.   Unit System - 60Hz  Max Flow - 6 GPM - 18.9 LPM Max Head - 12.1 FT - 2.5 M Power - .04 HP - .029 KW Electrical - 115V 60HZ Type - Centrifugal Mag Drive Inlet - 1/2"MPT Outlet - 1/2"MPT   Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)   Can handle liquids of 250F Materials and is FDA Food Compliant with 6 Foot Cord and plug Components are UL Recognized.   Made in American

Jabsco 12210-0003 Pump 115V Motor Pump Body: Bronze Port Size: 3/8" NPT Internal Pipe Thread and Adaptors for 3/4" garden hose thread Flow: 3.4 GPM at 10ft Pressure: 17.4 PSI Max Impeller: Neoprene or Nitrile Shaft Seal: Lip Type Motor: 115 Volt AC Intermittent duty with Replaceable Brushes, Stainless Steel Shaft, 6' cord, three prong grounding plug   APPLICATIONS The 12210-Series Pumps are the most compact self-priming flexible impeller 115 Volt AC Utility Pumps Jabsco offers.   INDUSTRIAL: Transferring liquids. Velocity-mixing. Pumping coolants. Pumping waste water to sewer. Cellar, yard and sump drainage. Cooling Heliarc welding equipment.   MARINE: Washing down decks and docks. Water for ship's service supply. Pumping out crank-case oil.   FARMING: Pumping water for stock, poultry houses, farmhouse. Pumping water from wells and cisterns. Pumping liquid ballast into tractor tires. Pumping water from flooded basements.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, cesspools, sumps, etc. Draining water heaters and water closets. Draining laundry tubs below sewer level. Removing water trapped between walls, draining inaccessible places when pipes break or leak. Draining fishing ponds and garden pools. Removing sludge, lye water and other caustics from stopped up drains and sinks.   Jabsco Flexible Impeller Utility Pump 115V 3.4GPM Nitrile Impeller  

Jabsco 1673-1003 Pump 1/2" Ped Mt FEATURES Pump Body: Bronze Port Size: 1/2" NPT Impeller: Nitrile Flow & Pressure: Varies by application. A half thickness cam is also available, (Where reduced capacity is required with a fixed speed.) Impeller: Neoprene or Nitrile (Oil Resistant) Shaft Seal: Lip Seal or Mechanical seal, Buna N Shaft: Stainless Steel Bearings: Sealed Ball Bearings    APPLICATIONS  This pump offers all the benefits of flexible impeller pumps in a compact size with moderate flow rate and horizontally oriented ports.   MARINE: Engine cooling, Pumping bilges, Washdowns, Circulating water in bait tanks, Utility dock side pump.   INDUSTRIAL: Circulating and transferring, Velocity-mixing, Pumping machine tool coolants, Return spill, Sump drainage, Chemicals,   Pharmaceuticals, Soap, Liquors, Ink, Dyes, Alcohol, Various acids, Tanning liquors, Glycerine, Brine, etc.   FARMING: Pumping water for stock, Pumping water from shallow wells and cisterns, Pumping liquid ballast into tractor tires.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, Cesspools, Sumps, Water heaters and water closets, Drains and sinks, Draining fishponds and pools   Jabsco Flexible Impeller Pedestal Pump 1/2"NPT Lip Seal Nitrile Impeller  

Jabsco 1673-2001 Pump 1/2" Npt Neo W/Mech Sl FEATURES Pump Body: Bronze Port Size: 1/2" NPT Flow & Pressure: Varies by application. A half thickness cam is also available, (Where reduced capacity is required with a fixed speed.) Impeller: Neoprene Shaft Seal: Mechanical seal Shaft: Stainless Steel Bearings: Sealed Ball Bearings    APPLICATIONS This pump offers all the benefits of a flexible impeller pumps in a compact size with moderate flow rate and horizontally oriented ports. MARINE: Engine cooling, Pumping bilges, Washdowns, Circulating water in bait tanks, Utility dock side pump.   INDUSTRIAL: Circulating and transferring, Velocity-mixing, Pumping machine tool coolants, Return spill, Sump drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Ink, Dyes, Alcohol, Various acids, Tanning liquors, Glycerine, Brine, etc.   FARMING: Pumping water for stock, Pumping water from shallow wells and cisterns, Pumping liquid ballast into tractor tires.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, Cesspools, Sumps, Water heaters and water closets, Drains and sinks, Draining fishponds and pools.     Jabsco Flexible Impeller Pedestal Pump 1/2"NPT Mechanical Seal Neoprene Impeller  

Jabsco 1673-1001 Flexible Impeller Pedestal Pump Pump Body: Bronze Port Size: 1/2" NPT Flow & Pressure: Varies by application. A half thickness cam is also available, (Where reduced capacity is required with a fixed speed.) Impeller: Neoprene or Nitrile (Oil Resistant) Shaft Seal: Lip Seal or Mechanical seal, Buna N Shaft: Stainless Steel Bearings: Sealed Ball Bearings    APPLICATIONS  This pump offers all the benefits of flexible impeller pumps in a compact size with moderate flow rate and horizontally oriented ports. MARINE: Engine cooling, Pumping bilges, Washdowns, Circulating water in bait tanks, Utility dock side pump.   INDUSTRIAL: Circulating and transferring, Velocity-mixing, Pumping machine tool coolants, Return spill, Sump drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Ink, Dyes, Alcohol, Various acids, Tanning liquors, Glycerine, Brine, etc.   FARMING: Pumping water for stock, Pumping water from shallow wells and cisterns, Pumping liquid ballast into tractor tires.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, Cesspools, Sumps, Water heaters and water closets, Drains and sinks, Draining fishponds and pools.   Jabsco Flexible Impeller Pedestal Pump 1/2"NPT Lip Seal Neoprene Impeller,  Kohler 15HP  

Jabsco 11860-0006 Pump 24V Elect Clutch   FEATURES Pump Body: Bronze Port Size: 11860-Series, 1" NPT Internal 11870-Series, 1-1/4" NPT Internal Electric: 12V, 24V or 32V Pulley: Single B groove or Double A groove Impeller: Nitrile Shaft Seal: Mechanical Carbon-Ceramic, Face Type Shaft: Stainless Steel Bearings: Shielded Ball Bearings   APPLICATIONS / CHARACTERISTICS This electrically activated clutch pump offers all the benefits of flexible impeller pumps with a substantial flow rate and horizontally oriented ports. The electric clutch offers convenient remote activation.   MARINE: Pumping bilges, Washdowns, Circulating water in bait tanks, Utility dock-side pump.     INDUSTRIAL: Circulating and transferring, Velocitymixing, Pumping machine tool coolants, Return spill, Sump drainage, Chemicals,   Pharmaceuticals, Soap, Liquors, Ink, Dyes, Alcohol, Various acids, Tanning Liquors, Glycerine, Brine, etc.   FARMING: Pumping water stock, Pumping water from shallow wells and cisterns.   PLUMBING AND HOME EMERGENCY USE: Pumping out flooded basements, Cesspools, Sumps, Water heaters and water closets, Drains and sinks, Draining fishponds and pools.   PUBLIC UTILITIES AND MUNICIPALITIES: Under the hood mounting on service trucks for draining meter boxes, manholes, excavations; For pollution control and watering for dust control.     Jabsco- Electric Clutch Pump 24V, 1" NPT Ports, 2 Groove "A" Belt Pulley