Automotive/RV Equipment and Supplies If you plan on taking the RV out for a weekend, a week, or an even longer trip, we have the RV equipment you need. Along with that we also have standard automotive equipment, so we can help you get ready for your trip, enjoy it, and stay safe even if you just take your car for a getaway. With the parts and supplies you need, like CB radios, power inverters, and vehicle laptop mounts, you will be prepared for the things that might come your way on the trip. Traveling in an RV or by car can be great fun, and give you the chance to see a lot of the country. The right supplies make it more enjoyable.   We offer a wide variety of accessories, so you can browse through satellite receivers, charger/inverter combos, fume detectors, and more. If you want to make sure you are headed in the right direction we offer compasses - magnetic, and you can get GPS - accessories and GPS - automotive/RV options that will work no matter what kind of vehicle you have. Plenty of choices means you can select what fits your budget and needs, and then head out down the road to the adventure you have planned.   Notice: Safe-T-Alert Fume Detectors, all products are on backorder.

GPS - Automotive/RV

Shurflo 8020-513-236 Pump 115V 60Sw Pvs Shurflo- Diaphragm Pump 3 Chamber, 1.5 GPM Open Flow, 115VAC Intermittent Duty, 60 PSI Demand Switch (adjustable 40-60 PSI), Viton Valves, Santoprene Diaphragm, Polypropylene Housing, 3/8" NPT Female Ports, Has a Power Cord, UL/CSA Recognized, General Industrial Pump

Battery Charger Attwood's Battery Charger is compact and perfect for your bench, garage or shop use. Overcharge, short circuit and reverse polarity protection provides years of worry free use. Provides 2 and 6 amp charge for 12V batteries. 6 amp charge for 6V batteries. Automatically switches to trickle charge mode after battery is fully charged. Dual rated 12 and 6 volt battery charger can be used for all of your marine, automotive, RV and sports applications. LED indicator - power on Ammeter indicates charging current 6 foot power cord length 48 inch battery connector leads WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SHURflo RV-10UC-A, Filter Housing SHURflo Filter Housing Waterguard, Non-Bypass Model, 10 Inch, 3/4" FPT Ports, Includes One RV-10C1-A Cartiridge, Garden Hose Fittings, Wrench and Mounting Bracket

Detroit Diesel 5196513 Gasket  

Tuthill 1LEV-C-A-88513-7 Pump And Motor

StarPod Kit for Starlink Roam/RV Antenna - Housing & Base The StarPod from NavPod is a waterproof housing designed for permanent mounting of the Starlink Roam/RV antenna, typically on a yacht’s hardtop or radar arch. The StarPod housing fits Starlink model UTA-212 (dish face measuring 20.2” x 11.9” / 513 mm x 303 mm). NavPod model SP212-K is the StarPod Kit, which includes the StarPod housing and a black powder-coated aluminum base. The included base is 8.25" tall with a 4" outer diameter and has a 6" circular footprint with four screw mounting holes. Third-Party Accessory Disclaimer: The NavPod and StarPod brands are in no way affiliated with the Starlink or SpaceX brands. The company's products are third-party accessories, distinct from the brands and products they are designed to house. What are the benefits of mounting a Starlink dish in a StarPod? StarPod protects Starlink and completely encloses the Starlink antenna in a very sturdy and attractive waterproof housing. Testing has proven that there is no degradation of signal inside the thermoformed acrylic-capped ABS housing. The Starlink Roam dish was originally designed for RVs, not boats. Its waterproof rating of IP54 is a long way from the IP67 rating NavPod is accustomed to in boating from the likes of Garmin, Raymarine, and others. Mounting a Starlink dish inside a StarPod provides additional protection from water intrusion, just as all NavPods have done for other marine electronics for over 25 years. How do I mount a Starlink dish inside a StarPod? The 4-legged "X" base that comes with a Starlink Roam dish is not utilized when mounting inside a StarPod; only the dish and attached mounting pole are used. The center post of the Starlink dish is inserted through the center hole in the bottom of the StarPod and extends into the chosen mounting pedestal. The initial Starlink setup process should be completed before mounting the dish inside a StarPod (refer to your Starlink setup and installation guide for this process). One important thing to note during the setup process is to make sure that the "Snow Melt" setting in the Starlink app is turned to "Off" (this feature produces excess heat to keep snow from piling up on a Starlink dish in winter environments, but is unnecessary and can potentially cause overheating when the dish is mounted inside a housing). Once the initial Starlink setup process is complete, the next step is to get the dish into a horizontal, or "flat" position, perpendicular to the mounting post. To get the dish into this position, unplug the Starlink dish, then plug it back in and turn it on. The dish will begin to move as part of its startup process, so just wait until it’s in a horizontal position and unplug the dish. This may take a couple of attempts, so just repeat as necessary until the dish is powered off in a horizontal or "flat" position. At this point, the dish can now be mounted inside the StarPod housing (using the instructions and hardware included with the StarPod). How can the Starlink dish move if it’s inside a StarPod? It can’t, but that’s okay. When powered on inside the StarPod housing, the Starlink dish will initially move as it looks for a signal. However, when the dish bumps into the inside of the housing and is unable to move any further, it will simply register an obstruction and discontinue its movement (a feature built into the dish to prevent the motor from burning out when it’s positioned next to a tree branch, ceiling, or other obstruction). The StarLink app may notify you of the obstruction, but the dish will continue to operate normally otherwise. There are several methods you can find on the internet for disabling your Starlink motor to achieve a fixed position. While these methods can be effective, it’s important to note that any modification of your Starlink antenna (drilling or cutting into the case, disconnecting internal cables, or any disassembly at all) will void the product warranty. If the Starlink dish can’t move, how can it get a good signal? Short Answer: A Starlink dish installed on a boat in a fixed horizontal position will achieve the same signal quality as a dish that’s free to move and adjust position. Long Answer: The Starlink Roam dish utilizes phased array technology. Rather than searching for a single satellite to point to (like older 18" and 24" satellite TV antennas), the Starlink dish is continuously switching between different satellites every few minutes (satellites that are moving at very high speeds and orbiting much lower than traditional TV and internet satellites). When a Starlink dish moves, it isn’t trying to point toward a particular satellite; it’s just looking for a clear view of the sky. Since this dish was originally designed for RV use, the movement of the dish was designed to allow it to point away from overhead obstructions like trees and buildings that might prevent a clear view of the sky. While this functionality makes sense for RV use, it is much less functional for boating use, where the dish would almost never encounter any overhead obstructions. When testing, a Starlink dish mounted and immobilized inside a StarPod achieved the same signal quality and internet speed as a dish that was free to move outside of a housing. Neither the fixed horizontal positioning nor the housing material itself resulted in any signal degradation as long as the dish had an otherwise clear view of the sky (as it typically would on a floating vessel). Liability Disclaimer: NavPod assumes no liability for any violation of Starlink product warranty or terms of service that may result from modifying a Starlink dish or mounting it inside a StarPod. General Information: StarPod is manufactured by Ocean Equipment in Bend, Oregon, USA, using the same time-proven materials that are used to fabricate the popular line of NavPods, waterproof housings for marine electronics. All NavPods Feature: Structural Rigidity – The Gen3 enhancements now include a thicker gauge of acrylic-capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening, and the more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All NavPods are manufactured with a double gasket system, providing an excellent watertight seal. This seal provides the best protection for your marine electronics. StarPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – The company uses all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets to match the NavPod wrench for better holding ability when tightening. The nickel-chrome-plated stainless steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – Navpod stands behind its commitment by offering a 10-year warranty on all new NavPods, including the StarPod.

StarPod Housing Only for Starlink Roam/RV Antenna - Base Not Included The StarPod from NavPod is a waterproof housing designed for permanent mounting of the Starlink Roam/RV antenna, typically on a yacht’s hardtop or radar arch. The StarPod housing fits Starlink model UTA-212 (dish face measuring 20.2” x 11.9” / 513 mm x 303 mm). NavPod model SP212-H includes the StarPod housing only and is intended for installations where the housing will be mounted on an existing or third-party pedestal. A compatible pedestal should have an upper mounting surface no larger than a 7.5” diameter circle, which is the available mounting surface on the bottom of a StarPod housing. Third-Party Accessory Disclaimer: The NavPod and StarPod brands are in no way affiliated with the Starlink or SpaceX brands. The company's products are third-party accessories, distinct from the brands and products they are designed to house. What are the benefits of mounting a Starlink dish in a StarPod? StarPod protects Starlink and completely encloses the Starlink antenna in a very sturdy and attractive waterproof housing. Testing has proven that there is no degradation of signal inside the thermoformed acrylic-capped ABS housing. The Starlink Roam dish was originally designed for RVs, not boats. Its waterproof rating of IP54 is a long way from the IP67 rating NavPod is accustomed to in boating from the likes of Garmin, Raymarine, and others. Mounting a Starlink dish inside a StarPod provides additional protection from water intrusion, just as all NavPods have done for other marine electronics for over 25 years. How do I mount a Starlink dish inside a StarPod? The 4-legged "X" base that comes with a Starlink Roam dish is not utilized when mounting inside a StarPod; only the dish and attached mounting pole are used. The center post of the Starlink dish is inserted through the center hole in the bottom of the StarPod and extends into the chosen mounting pedestal. The initial Starlink setup process should be completed before mounting the dish inside a StarPod (refer to your Starlink setup and installation guide for this process). One important thing to note during the setup process is to make sure that the "Snow Melt" setting in the Starlink app is turned to "Off" (this feature produces excess heat to keep snow from piling up on a Starlink dish in winter environments, but is unnecessary and can potentially cause overheating when the dish is mounted inside a housing). Once the initial Starlink setup process is complete, the next step is to get the dish into a horizontal, or "flat" position, perpendicular to the mounting post. To get the dish into this position, unplug the Starlink dish, then plug it back in and turn it on. The dish will begin to move as part of its startup process, so just wait until it’s in a horizontal position and unplug the dish. This may take a couple of attempts, so just repeat as necessary until the dish is powered off in a horizontal or "flat" position. At this point, the dish can now be mounted inside the StarPod housing (using the instructions and hardware included with the StarPod). How can the Starlink dish move if it’s inside a StarPod? It can’t, but that’s okay. When powered on inside the StarPod housing, the Starlink dish will initially move as it looks for a signal. However, when the dish bumps into the inside of the housing and is unable to move any further, it will simply register an obstruction and discontinue its movement (a feature built into the dish to prevent the motor from burning out when it’s positioned next to a tree branch, ceiling, or other obstruction). The StarLink app may notify you of the obstruction, but the dish will continue to operate normally otherwise. There are several methods you can find on the internet for disabling your Starlink motor to achieve a fixed position. While these methods can be effective, it’s important to note that any modification of your Starlink antenna (drilling or cutting into the case, disconnecting internal cables, or any disassembly at all) will void the product warranty. If the Starlink dish can’t move, how can it get a good signal? Short Answer: A Starlink dish installed on a boat in a fixed horizontal position will achieve the same signal quality as a dish that’s free to move and adjust position. Long Answer: The Starlink Roam dish utilizes phased array technology. Rather than searching for a single satellite to point to (like older 18" and 24" satellite TV antennas), the Starlink dish is continuously switching between different satellites every few minutes (satellites that are moving at very high speeds and orbiting much lower than traditional TV and internet satellites). When a Starlink dish moves, it isn’t trying to point toward a particular satellite; it’s just looking for a clear view of the sky. Since this dish was originally designed for RV use, the movement of the dish was designed to allow it to point away from overhead obstructions like trees and buildings that might prevent a clear view of the sky. While this functionality makes sense for RV use, it is much less functional for boating use, where the dish would almost never encounter any overhead obstructions. When testing, a Starlink dish mounted and immobilized inside a StarPod achieved the same signal quality and internet speed as a dish that was free to move outside of a housing. Neither the fixed horizontal positioning nor the housing material itself resulted in any signal degradation as long as the dish had an otherwise clear view of the sky (as it typically would on a floating vessel). Liability Disclaimer: NavPod assumes no liability for any violation of Starlink product warranty or terms of service that may result from modifying a Starlink dish or mounting it inside a StarPod. General Information: StarPod is manufactured by Ocean Equipment in Bend, Oregon, USA, using the same time-proven materials that are used to fabricate the popular line of NavPods, waterproof housings for marine electronics. All NavPods Feature: Structural Rigidity – The Gen3 enhancements now include a thicker gauge of acrylic-capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening, and the more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All NavPods are manufactured with a double gasket system, providing an excellent watertight seal. This seal provides the best protection for your marine electronics. StarPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – The company uses all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets to match the NavPod wrench for better holding ability when tightening. The nickel-chrome-plated stainless steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – Navpod stands behind its commitment by offering a 10-year warranty on all new NavPods, including the StarPod.

  Join the RV Geeks and the Tech Doctor Live on Thursday August 12th, 5pm PST/8pm EST for a LIVE SOLAR Q&A.   Join the Xantrex Q&A live webinar with John and Peter of the RV Geeks! They want to answer all your solar questions live on YouTube with the help of Tech Doctor Don Wilson and Xantrex product expert, Wesley Shuen.   Solar has evolved and is more efficient today than in the past. Whether you are installing solar for the first time or are in the exploration stage or want to upgrade an existing system, this Livestream is for everyone. The RV Geeks, Don Wilson, and Wesley Shuen want to answer all your questions. If you need help and guidance on anything related to solar, join the Livestream and consult the professionals directly!    Don't forget CLR Marine for all your Xantrex Needs.   Watch at: https://www.youtube.com/watch?v=DMy6C5vQ4y4  

Automotive Leather 3-In-1 Complete Care - 16oz 303 Automotive Leather 3-in-1 Complete Care cleans, conditions and provides UV protection to all finished leather and vinyl.  It will help clean up surface dirt and grime, as well as helps repel future dust, lint and stains.   Also contains superior UV protection to prevent fading and cracking of the leather caused by the sun’s harmful UV rays.   Easy to use formula, just spray on and wipe off.  Features: No residue left behind Repels dust, lint & stains Conditions leather surface to prevent cracking & fading Provides UV protection for all finished automotive leather & vinyl Safe for use on all finished car leather & vinyl surfaces Made in the U.S.A. *Sold as an Individual WARNING: This product can expose you to chemicals including Ethylbenzene which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Automotive Leather 3-In-1 Complete Care - 16oz *Case of 6* 303 Automotive Leather 3-in-1 Complete Care cleans, conditions and provides UV protection to all finished leather and vinyl.  It will help clean up surface dirt and grime, as well as helps repel future dust, lint and stains.   Also contains superior UV protection to prevent fading and cracking of the leather caused by the sun’s harmful UV rays.   Easy to use formula, just spray on and wipe off.  Features: No residue left behind Repels dust, lint & stains Conditions leather surface to prevent cracking & fading Provides UV protection for all finished automotive leather & vinyl Safe for use on all finished car leather & vinyl surfaces Made in the U.S.A. *Sold as a Case Pack WARNING: This product can expose you to chemicals including Ethylbenzene which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Haight Pump 30U-VMS Pump Vit Mech Sl No Rv Features Pump Body: Ductile Iron Impeller: Steel Shaft  Seal: Viton Mechanical Seal Inlet Port is 3/4 inch NPT Discharge Port is 3/4 inch NPT   Haight 3U-VMS is a Ductile Iron Gear Pump, round hub Pump End Only less motor, 3 GPM rated, with Ductile Iron Construction, Viton Mechanical Seal, Steel Shaft, Steel Gears, Iron Rotor and Bearings. The standard construction materials of this pump are Ductile Iron Housing, Steel Shaft and Pinion Gears, Iron Rotor and Bearings, Buna N Lip Seals and Elastomers. These gear pumps have a Gear within a gear internal design and is very effective at handling a broad range of applications while operating at standard motor speeds, and reducing wear. Both of these operating characteristics play an important role in minimizing overall capital investment, and operating expenses. Compact rugged, and easy to maintain, these pumps are ideally suited to close-coupled mounting, or direct mounting to the motor. These pumps can operate at standard motor speeds, eliminating the need for pulleys/gear reducers. The involute gear design offers excellent suction characteristics, and minimizes noise and reduces internal bypassing It comes standard with self-lubricating gramix iron bearings, and easy to maintain Buna-N lip seals. The seals are installed in the UniverSeal design for simple and quick replacement, or change to alternate seal style. This is just the bare pump end, but there are optional mounting brackets which are designed for in-line mounting with standard NEMA frame size motors or bedplate mounting. These pumps are self-priming and will develop up to 27 inches of vacuum. Pumps will operate in either direction, and flow direction in the pump can be changed without disrupting the attached piping, or special tools.   Applications Petroleum Products Machine Manufacturing Applications Machine Tools Hydraulic Equipment Lubrication Systems Glue and Ink Soap and Detergent Products Building and Highway Contractors Paper Products Industries Automotive Applications Shipbuilding Applications Aircraft Applications Mining Applications  

Haight Pump 54UR-VMS Pump Vit Mech Sl Rv Specifications Construction Material:  Ductile Iron Capacity (max):  54 gpm Discharge Pressure (max):  250 psi Temperature:  620 degrees FT Inlet Port is 2 inch NPT and 2 inch ANSI Flange Discharge Port is 2 inch NPT and 2 inch ANSI Flange Seal: Viton Mechanical Seal Pump End Only less motor   54U - DIU Series Double Positive Displacement Pumps   These gear pumps have a Gear within a gear internal design and is very effective at handling a broad range of applications while operating at standard motor speeds, and reducing wear. Both of these operating characteristics play an important role in minimizing overall capital investment, and operating expenses. Compact rugged, and easy to maintain, these pumps are ideally suited to close-coupled mounting, or direct mounting to the motor. These pumps can operate at standard motor speeds, eliminating the need for pulleys/gear reducers. The involute gear design offers excellent suction characteristics, and minimizes noise and reduces internal bypassing It comes standard with self-lubricating gramix iron bearings, and easy to maintain Buna-N lip seals. The seals are installed in the UniverSeal design for simple and quick replacement, or change to alternate seal style. This is just the bare pump end, but there are optional mounting brackets which are designed for in-line mounting with standard NEMA frame size motors or bedplate mounting. These pumps are self-priming and will develop up to 27 inches of vacuum. Pumps will operate in either direction, and flow direction in the pump can be changed without disrupting the attached piping, or special tools.   Applications Petroleum Products Machine Manufacturing Applications Machine Tools Hydraulic Equipment Lubrication Systems Diesel Engines Food Processing Restaurant Equipment Misc. Chemical Applications Glue and Ink Soap and Detergent Products Building and Highway Contractors Paper Products Industries Automotive Applications Shipbuilding Applications    

Haight Pump 54U-VMS Pump Vit Mech Sl No Rv Specifications Construction Material:  Ductile Iron Capacity (max):  54 gpm Discharge Pressure (max):  250 psi Temperature:  620 degrees FT Inlet Port is 2 inch NPT and 2 inch ANSI Flange Discharge Port is 2 inch NPT and 2 inch ANSI Flange Seal: Viton Mechanical Seal Pump End Only less motor   54U - DIU Series Double Positive Displacement Pumps   These gear pumps have a Gear within a gear internal design and is very effective at handling a broad range of applications while operating at standard motor speeds, and reducing wear. Both of these operating characteristics play an important role in minimizing overall capital investment, and operating expenses. Compact rugged, and easy to maintain, these pumps are ideally suited to close-coupled mounting, or direct mounting to the motor. These pumps can operate at standard motor speeds, eliminating the need for pulleys/gear reducers. The involute gear design offers excellent suction characteristics, and minimizes noise and reduces internal bypassing It comes standard with self-lubricating gramix iron bearings, and easy to maintain Buna-N lip seals. The seals are installed in the UniverSeal design for simple and quick replacement, or change to alternate seal style. This is just the bare pump end, but there are optional mounting brackets which are designed for in-line mounting with standard NEMA frame size motors or bedplate mounting. These pumps are self-priming and will develop up to 27 inches of vacuum. Pumps will operate in either direction, and flow direction in the pump can be changed without disrupting the attached piping, or special tools.   Applications Petroleum Products Machine Manufacturing Applications Machine Tools Hydraulic Equipment Lubrication Systems Diesel Engines Food Processing Restaurant Equipment Misc. Chemical Applications Glue and Ink Soap and Detergent Products Building and Highway Contractors Paper Products Industries Automotive Applications Shipbuilding Applications