|
7,500lb Disc Brake Actuator – Tie Down Engineering Model
The Model 750E works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the tow vehicle axle brakes. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in dampening shock absorber retards the telescoping shock against the hitch ball. Be sure to comply with the regulations for brakes in the state. Brake laws are sometimes minimum standards, and users may wish to add additional brakes to a trailer.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator. The Model 750E Actuator is completely assembled and ready to bolt into place if not all ready-installed. Manufactured for tongue sizes: 3”x 3”, 3”x 4", and 3”x 5”.
Features:
7,500 lbs. capacity
Fits 2″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 7,500 lbs.
Maximum Tongue Load: 750 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight).
|
418.24 |
|
|
8,500lb Disc Brake Actuator – Tie Down Engineering Model
The Model 850E works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the tow vehicle axle brakes. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in dampening shock absorber retards the telescoping shock against the hitch ball. Be sure to comply with the regulations for brakes in your state. Brake laws are sometimes minimum standards, and users may wish to add additional brakes to a trailer.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator. The Model 850E Actuator is completely assembled and ready to bolt into place if not all ready-installed. Manufactured for tongue sizes: 3”x 3”, 3”x 4” & 3”x 5”.
Features:
8,500 lbs. capacity
Fits 2″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 8,500 lbs.
Maximum Tongue Load: 850 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight).
|
550.45 |
|
|
6,600lb Disc Brake Actuator – Tie Down Engineering Model
The Model 660E works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the tow vehicle axle brakes. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in dampening shock absorber retards the telescoping shock against the hitch ball. Be sure to comply with the regulations for brakes in your state. Brake laws are sometimes minimum standards, and you may wish to add additional brakes to a trailer.
Read the tow vehicle's owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator. The Model 660E Actuator is completely assembled and ready to bolt into place, if not already installed. Manufactured for tongue sizes: 3”x 3”, 3”x 4” & 3”x 5”.
Features:
6,600 lbs. capacity
Fits 2″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 6,600 lbs.
Maximum Tongue Load: 650 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight).
|
329.21 |
|
|
16,500lb Capacity Disc Brake Actuator with 2-5/16″ Coupler
The Model 16.5 works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the brakes on the tow vehicle. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in, sealed, independent dampening shock absorber controls the telescoping shock against the hitch.
Be sure to comply with the regulations for brakes in the state. Brake laws are sometimes minimum standards, and users may wish to add brakes to a trailer to meet minimum Gross Vehicle Weight Ratings (G.V.W.R.). Note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator.
The Model 16.5 Actuator is completely assembled and ready to bolt into place (tongue sizes: 3”x 4” & 3”x 5”, 9 ga. min.)
Features:
16,500 lbs. capacity
Fits 2-5/16″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 16,500 lbs.
Maximum Tongue Load: 1,650 lbs.
Minimum Tongue Weight: 5% of G.V.W.R.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as total gross weight.
|
883.36 |
|
|
20,000lb Capacity Disc Brake Actuator with 2-5/16″ Coupler
The Model works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the brakes on the tow vehicle. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in, sealed, independent dampening shock absorber controls the telescoping shock against the hitch.
Be sure to comply with the regulations for brakes in the state. Brake laws are sometimes minimum standards, and users may wish to add brakes to a trailer to meet minimum Gross Vehicle Weight Ratings (G.V.W.R.). Note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator.
Features:
20,000 lbs. capacity
Fits 2-5/16″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 16,500 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as total gross weight.
|
1121.09 |
|
|
Kwik-Lok Transom Tie-Downs
Quantity: 2
Dimensions: 1" x 4'
Break Strength: 1,200 lbs./ea
Safe Work Load: 400 lbs
The Kwik-Lok buckle tie-downs feature vinyl-coated top hooks,zinc-coated trailer hooks,along with durable polypropylene webbing and a protective web pad.
|
18.40 |
|
|
Kwik-Lok Transom Tie-Downs
Quantity: 2
Dimensions: 2" x 2'
Break Strength: 1,200 lbs./ea
Safe Work Load: 400 lbs
The Kwik-Lok buckle tie-downs feature vinyl-coated top hooks, zinc-coated trailer hooks, along with durable polypropylene webbing and a protective web pad.
|
20.92 |
|
|
Kwik-Lok Transom Tie-Downs
Quantity: 2
Dimensions: 2" x 4'
Break Strength: 1,200 lbs./ea
Safe Work Load: 400 lbs
The Kwik-Lok buckle tie-downs feature vinyl-coated top hooks,zinc-coated trailer hooks,along with durable polypropylene webbing and a protective web pad.
|
19.43 |
|
|
Kwik-Lok Transom Tie-Downs
Quantity: 2
Dimensions: 2" x 6'
Break Strength: 1,200 lbs./ea
Safe Work Load: 400 lbs
The Kwik-Lok buckle tie-downs feature vinyl-coated top hooks,zinc-coated trailer hooks,along with durable polypropylene webbing and a protective web pad.
|
24.64 |
|
|
Mini G3 Retractable Transom Tie-Down System - 1" x 72"
Just hook, ratchet and go! Never look for lost tie-downs again. The Mini G3 Transom tie-down can be permanently mounted with one bolt to most boat trailers. Six feet of one-inch webbing enables you to tie down more equipment in more applications, conveniently and securely.
Features:
Permanent one-bolt installation
Self-retracting web
Anti-corrosive construction
Break Strength 1,400lbs/ea
SWL 466lbs/ea
|
56.50 |
|
|
12″ AutoFlex Knott Disc Brake Kit
Load Rite's 6-lug, 12-inch vented rotor disc brake kit is manufactured by AutoFlex KNOTT and fits UFP 6,000 lbs. capacity 6-bolt axles. Does not fit Tie Down.
Kit Includes:
Vented cupped and studded, zinc rotor, and hub assembly
Loaded caliper assembly with pads
Full inner and outer bearings, races, and corresponding seal
Dust cap, lug nuts, and mounting hardware
*LH/RH Compatible
*Quantity (2) Kits Required Per Axle Assembly
|
393.60 |
|
|
10″ Knott Disc Brake Kit
Load Rite's 5-lug, 10-inch vented integral rotor disc brake kit is manufactured by AutoFlex KNOTT and fits KNOTT 3,700 lbs. capacity 5-bolt axles.
Kit Includes:
Vented cupped and studded, zinc rotor, and hub assembly
Loaded caliper assembly with pads
Full inner and outer bearings, races, and corresponding seal
Dust cap, lug nuts, and mounting hardware
*LH/RH Compatible
*Quantity (2) Kits Required Per Axle Assembly
|
316.85 |
|
|
9.6″ Dexter Vented Rotor Disc Brake Kit
Load Rite's 5-lug, 9.6-inch vented rotor disc brake kit is manufactured by Dexter and fits a standard 3,750 lbs capacity spindle.
Kit Includes:
Vented rotor with Galvx finish
Aluminum caliper with e-coat finish
Ceramic pads with backing plates
Galvanized heavy-duty mounting bracket
Dust cap, slider pins, and hardware
Pre-greased rotors include bearings, races, and seals
*Quantity (2) Kits Required Per Axle Assembly
|
296.51 |
|
|
12″ Dexter Vented Rotor Disc Brake Kit
Load Rite's 6-lug, 12-inch vented rotor disc brake kit is manufactured by Dexter and fits a standard 3,000-capacity spindle.
Kit Includes:
Vented rotor with Galvx finish
Aluminum caliper with e-coat finish
Ceramic pads with backing plates
Galvanized heavy-duty mounting bracket
Dust cap, slider pins, and hardware
Pre-greased rotors include bearings, races, and seals
*Quantity (2) Kits Required Per Axle Assembly
|
337.60 |
|
|
Load Rite
Easy to load and unload - whether you're hauling an 11' jon boat, a pontoon boat, personal watercraft, motorcycle, snowmobile, a 34' sport boat, or even some garden mulch - nothing makes the ride smoother, the launch and load easier than a Load Rite.
|
|