|
Adhesive Mixing Tip For AT-6030
Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing tip with more mixing chambers to insure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips. pkg contains 50 mixing tips.
|
66.22 |
|
|
AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10
Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.
Features:
Square Mixing Tip
4" Long
Case of 10
|
14.98 |
|
|
AT-850 Square Mixing Tip 4" - Case of 50
Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any possibility of the cartridge plugging up as the entry is separated.
Features:
Square Mixing Tip
4" Long
Case of 50
|
69.79 |
|
|
Adhesive Mixing Tip For AT-6030
Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing tip with more mixing chambers to insure proper mixing before use. These mixing tips minimize waste compared with traditional 6" mixing tips. pkg contains 10 mixing tips.
|
14.78 |
|
|
Adhesive Dispensing Gun with 10:1 Plunger for AT-6030 Adhesive Only
The AT- 301 Adhesive Dispensing Gun Is Designed Specifically For Use With Our AT-6030 38 ml 10:1 Adhesive Cartridge. This Hand Operated Gun And Our Mixing Tips Provide Precise Mixing And Dispensing Of Our Adhesives. The Mixing Tip Is Easily Replaced Should The Glue Set Up. We Recommend 5 Mixing Tips Per Cartridge Of Adhesive. A 10:1 Adhesive Plunger Is Included With Gun.
|
68.05 |
|
|
10:1 Gun Plunger for AT-6030 Adhesive
10 Pack Gun Plunger for AT-6030 Adhesive
|
61.20 |
|
|
10:1 Gun Plunger for AT-6030 Adhesive
Single Pack gun plunger for AT-6030 Adhesive
|
11.96 |
|
|
Executive Adhesive & Fastener Kit w/AT-8040 Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Contains 1 Tube Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastic Or Rubber. AT-8040 Will Hold Even Our Heaviest Parts on a Vertical or Overhead Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225°. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year.
The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.
The AT-1001003 Kit Contains:
(1) AT-8040 - No Slide Multi Bonder Acrylic Adhesive
<(1) AT-300 - Dispensing Gun
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(100) AT-5 - Large White Cable Tie Mount
(50) AT-3 - Small White Cable Tie Mount
(4) AT-113 - Large Footman's Strap
(10) PS62-832-16SS - 1.00" Long Panel Stud
(4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base
(4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base
(1) Plano Storage Box 14" x 9" x 2.75"
Step By Step Instructions
|
238.40 |
|
|
Executive Fastener Kit - No Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard Or Custom Builder. The Kit Does NOT Contain Acrylic Adhesive
The Weld Mount System Eliminates The Need To Drill Into Cored Composites Which Can Result In Hull & Deck Delaminations. No Need To Drill, Tap, or Weld When Used On Metal Surfaces. Great For Mounting Electronics, Wire Runs, Bilge Applications, Water Separators, Battery Switches, Etc.
The AT-1001008 Kit Contains:
(1) AT-300 - Dispensing Gun
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(100) AT-5 - Large White Cable Tie Mount
(50) AT-3 - Small White Cable Tie Mount
(4) AT-113 - Large Footman's Strap
(10) PS62-832-16SS - 1.00" Long Panel Stud
(4) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1420-24SS - 1.50" Long Stud With 1/4 x 20 Threads 1.25" Base
(4) ST125-1024-12SS - .75" Long Stud With #10 x 24 Threads 1.25" Base
(4) ST125-1024-24SS - 1.50" Long Stud With #10 x 24 Threads 1.25" Base
(1) Plano Storage Box 14" x 9" x 2.75"
Step By Step Instructions
|
202.60 |
|
|
Industrial Kit with AT-8040 Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System. The Kit Contains 1 Tubes Of Our AT-8040 No Slide Multi Bonder Acrylic Adhesive Which Will Bond To Almost All Surfaces Except Low Energy Plastics And Rubber. AT-8040 Will Hold Even Our Heaviest Parts On An Overhead Or Vertical Surface Without Fixturing. The Adhesive Sets in 12 Minutes And Is Heat Resistant To 225 Degrees. The Adhesive Should Be Refrigerated and Has A Shelf Life Of 1 year.
The Weld Mount System Eliminates The Need To Drill And Tap, or Weld When Used On Metal Surfaces. Great for Mounting Wire and Conduit Runs, Electrical Boxes And Other Structural Applications.
The AT-7001 Kit Contains:
(1) AT-8040 - No Slide Multi Bonder Adhesive With 12 Minute Kick
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(1) AT-300 - Adhesive Dispensing Gun
(30) AT-3B - Small Black Cable Tie Mount
(100) AT-5B - Large Black Cable Tie Mount
<(25) AT-5 - Large White Cable Tie Mount
(25) AT-7 - Aluminum Base Swivel Wire Tie Mount
(25) AT-9 - Aluminum Wire Tie Mount
(2) AT-113 - Large Footman's Strap White
(2) AT-113B - Large Footman's Strap Black
(6) ST125-1420-12SS - 0.75" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1024-12SS - 0.75" Long Stud With #10 x 24 Threads 1.25" Base
(6) ST125-1024-20SS - 1.25" Long Stud With #10 x 24 Threads 1.25" Base
(2) SHC-1000 - Single Hose Clamp 1.00"
(2) DHC-1000 - Double Hose Clamp 1.00"
(1) Storage Box - Durham Manufacturing 18.5' x 12.5" x 3.25"
Step By Step Instructions
|
350.40 |
|
|
Industrial Kit - No Adhesive
This Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For Industrial Maintenance Shops. A Wide Selection Of Weld Mount Parts Are Supplied In A Heavy "Durham" Metal Box Which Is A Standard Rack Mounted System.
The Weld Mount System Eliminates The Need To Drill And Tap, or Weld When Used On Metal Surfaces. Great for Mounting Wire and Conduit Runs, Electrical Boxes And Other Structural Applications.
The AT-7008 Kit Contains:
(10) AT-850 - 3.5" Mixing Tips For AT-8040 Adhesive
(1) AT-300 - Adhesive Dispensing Gun
(30) AT-3B - Small Black Cable Tie Mount
(100) AT-5B - Large Black Cable Tie Mount
(25) AT-5 - Large White Cable Tie Mount
(25) AT-7 - Aluminum Base Swivel Wire Tie Mount
(25) AT-9 - Aluminum Wire Tie Mount
(2) AT-113 - Large Footman's Strap White
(2) AT-113B - Large Footman's Strap Black
(6) ST125-1420-12SS - 0.75" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1420-16SS - 1.00" Long Stud With 1/4 x 20 Threads 1.25" Base
(6) ST125-1024-12SS - 0.75" Long Stud With #10 x 24 Threads 1.25" Base
(6) ST125-1024-20SS - 1.25" Long Stud With #10 x 24 Threads 1.25" Base
(2) SHC-1000 - Single Hose Clamp 1.00"
(2) DHC-1000 - Double Hose Clamp 1.00"
(1) Storage Box - Durham Manufacturing 18.5' x 12.5" x 3.25"
Step By Step Instructions
|
318.40 |
|
|
Adhesively Bonded Fastener Kit with AT 8040 Adhesive
Kit Contains:
(1) Plano Storage Box - 11" x 7.25" x 2.75"
(50) AT-5 Tie Mount (White)
(1) AT-8040 Adhesive
(5) AT-850 Mixing Tip
(1) AT-300 Dispensing Gun
(2) AT-113B Black Footmans Loop
(4) ST125-1420-16 Stainless Stud
|
158.53 |
|
|
Single Clamp
Each clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.
Features:
Hose OD: 0.250"
Stud Required: ST125-1420-12SS
Clamp Dimensions L/W/D: 0.87" x 0.47" x 0.41"
Recommended Clamp Spacing: 3'
|
17.83 |
|
|
Single Clamp
Each clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.
Features:
Hose OD: 0.375"
Stud Required: ST125-1420-16SS
Clamp Dimensions L/W/D: 1.06" x 0.63" x 0.56"
Recommended Clamp Spacing: 3'
|
23.78 |
|
|
Single Clamp
Each clamp is designed to be mounted using 1/4" x 20 Weld Mount studs. The clamps are manufactured in black polypropylene and are temperature rated for -22 to +194 degrees F continuous service.
Features:
Hose OD: 0.5"
Stud Required: ST125-1420-24SS
Clamp Dimensions L/W/D: 1.39" x 0.79" x 0.89"
Recommended Clamp Spacing: 4'
|
32.21 |
|