|
Used to hold the driveshaft on Yamaha PWC's when removing the impeller. Tool should be held by a bench vise.
|
11.79 |
|
|
Solas impeller wrench for removal and installation of PWC impellers. See Solas Impeller Accessories and Installation Guide in the Medart Marine general catalog for application information.
|
11.79 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
34.99 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
38.99 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
36.99 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
67.89 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
103.79 |
|
|
Shurflo 8000-543-250-SKA-S Pump Assembly 12V
Diaphragm Pump with 12 Volt DC Motor and 60 PSI Bypass. Polypropylene Pump Body, Viton Valves, Santoprene Diaphragm. Inlet Port is 3/8 Inch-18 NPT Female, Discharge Port is 3/8 Inch-18 NPT Female. 1.4 GPM open flow.
Features :
Pump Body:Polypropylene
Impeller:Viton
Shaft:Santoprene
Port Size:Inlet Port is 3/8 Inch-18 NPT Female, Discharge Port is 3/8 Inch-18 NPT Female. Motor Specs :12 Volt DC, Permanent Magnet, P/N 11-111-00.
|
196.08 |
|
|
We boaters can put a lot of wear and tear on our boats, especially on the propellers. When a propeller is bent, cracked or otherwise damaged, it can sometimes be difficult to identify a replacement. Fortunately, we make things a lot easier with Turning Point Propellers.
Turning Point propellers use a unique interchangeable hub design that allows easy replacement and upgrades of existing propellers. Simply identify the right prop hub for your application to easily switch props on and off depending on your needs.In addition to the easy repair and replacement,
Turning Point propellers are fast and fuel efficient, have impressive handling, best-in-class reverse control, are corrosion and impact-resistant, and are cheaper to replace than typical propellers. Plus, you can fit Turning Point props onto Mercury Flo-Torq II, Solex Rubex and Michigan Wheel XHS hubs without any additional components.
To identify the right hub and prop for your application, check out the Turning Point Prop Wizard Click on Tools then Turning Prop Wizard. Have your volume on and you will be walked through your propeller selection.
Specials Rebates Close Outs Remanufactured
|
|
|
Used to hold the driveshaft on Yamaha PWC's when removing the impeller. Tool should be held by a bench vise.
|
8.19 |
|
|
Solas impeller wrench for removal and installation of PWC impellers. See Solas Impeller Accessories and Installation Guide in the Medart Marine general catalog for application information.
|
11.99 |
|
|
Used to hold the driveshaft on Yamaha PWC's when removing the impeller. Tool should be held by a bench vise.
|
11.99 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
38.99 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
49.89 |
|
|
Replacement rubber hub bushings for Solas props with pressed in hubs. Excellent gripping force to keep the prop from slipping, Rubber compound is strong and durable. Hydraulic press required to press hubs in and out of the prop. Unless noted, fits both aluminum and stainless steel propellers.
|
53.79 |
|