|
12 Vane pump assembly for 1498cc SX-R. Use with Solas KGX Concord impeller. Includes housing, stator, impeller shaft, bearing, oil seal, cone, nozzle, steering nozzle and trim ring. 148mm diameter. 74mm hub size.
|
1422.99 |
|
|
Hypro 9203P-S, Polypropylene Centrifugal Pump
1-1/2" NPT Inlet, 1-1/4" NPT Outlet. 7/8" Solid, 316 Stainless Steel Shaft. CCW Rotation 100 gpm, 82 psi.
Hypro centrifugal pumps handle big, high-capacity spraying jobs with ease. Use them for spraying liquid fertilizers and other chemicals, including wettable powder slurries for weed control. Make short work of other jobs - filling nurse tanks, watering seed beds, and transferring liquids.
The broad, versatile line includes models with rugged housings of polypropylene that stand up to strong chemical herbicides. Polypropylene pumps are lightweight and provide excellent resistance to corrosive chemicals.
|
711.41 |
|
|
Shurflo 8000-543-250-SKA-S Pump Assembly 12V
Diaphragm Pump with 12 Volt DC Motor and 60 PSI Bypass. Polypropylene Pump Body, Viton Valves, Santoprene Diaphragm. Inlet Port is 3/8 Inch-18 NPT Female, Discharge Port is 3/8 Inch-18 NPT Female. 1.4 GPM open flow.
Features :
Pump Body:Polypropylene
Impeller:Viton
Shaft:Santoprene
Port Size:Inlet Port is 3/8 Inch-18 NPT Female, Discharge Port is 3/8 Inch-18 NPT Female. Motor Specs :12 Volt DC, Permanent Magnet, P/N 11-111-00.
|
196.08 |
|
|
Sherwood M-71 Engine Cooling Pump
Replaces Cummins 3907458 and 3912019. Also Replaces Sherwood M70.
Pump Body: Bronze
Ports: 1 1/4" Hose
Cam: Full
Impeller: Neoprene
Shaft Seal: Mechanical
Drive: Flange Mounted to Engine.
APPLICATIONS
Flexible Impeller Engine Cooling Pump.
|
616.40 |
|
|
We boaters can put a lot of wear and tear on our boats, especially on the propellers. When a propeller is bent, cracked or otherwise damaged, it can sometimes be difficult to identify a replacement. Fortunately, we make things a lot easier with Turning Point Propellers.
Turning Point propellers use a unique interchangeable hub design that allows easy replacement and upgrades of existing propellers. Simply identify the right prop hub for your application to easily switch props on and off depending on your needs.In addition to the easy repair and replacement,
Turning Point propellers are fast and fuel efficient, have impressive handling, best-in-class reverse control, are corrosion and impact-resistant, and are cheaper to replace than typical propellers. Plus, you can fit Turning Point props onto Mercury Flo-Torq II, Solex Rubex and Michigan Wheel XHS hubs without any additional components.
To identify the right hub and prop for your application, check out the Turning Point Prop Wizard Click on Tools then Turning Prop Wizard. Have your volume on and you will be walked through your propeller selection.
Specials Rebates Close Outs Remanufactured
|
|
|
Did your boat survive the 4th of July extended weekend? We sure hope so. We're also sure that someone has found a new and interesting way to break something on their boat. And we're also guessing that the propeller was treated to an especially rough time.
The good news is that CLR Marine carries Turning Point replacement propellers and hubs. These uniquely designed hubs allow for easy interchange of props, so once a hub is installed, replacing a propeller is easy. That means you can quickly change to a different size propeller for increased speed or power, and you can also quickly get back on the water when those underwater rocks jump in your way.
Turning Point propellers and hubs are specific to the application and size. Use the Turning Point Prop Wizard to help you find the right prop for your bpat.
Specials Closeouts Remanufactured Rebates
|
|
|
CLR Marine carries Solas® Amita 3-Blade Mercury 6-15hp aluminum boat propellers that utilize a state-of-the-art squeeze-casting process & makes these aluminum boat propellers stronger and tougher than traditional die-cast boat propellers. To learn more visit this link.
We also have a custom propeller search tool, making it SUPER EASY to find your replacement propeller today!
|
|
|
Easy, Quick & Hassle Free
The portable oil change bucket features the reliable, heavy-duty F3B-19 flexible impeller pump with an integrated flow reversing switch. The F3B-19 Oil Change Bucket from Johnson Pump provides your service shop with a dependable and long-lasting oil change solution.
Features:
5.5 gallons per minute
Flexible Impeller Pump Assembly
Easy, quick, no-mess, no-hassle, oil change package
Replaceable impeller - nonfixed
Automatic shut off
Complete, ready to use
Portable and convenient
High-temperature resistant dipstick tube
Heavy-duty extended 8' alligator clips easily clamp directly onto the battery
Sealed lid with easy-to-use pour spout for emptying used oil
Better Quality, Better Performance
The preferred OEM replacement for Sherwood 1500k impeller.
Made with the patented MC 97 rubber compound this impeller is designed
to provide maximum engine performance and adheres to strict tolerance
manufacturing with exact OEM dimensions.
• Proven longer impeller life
• Less material failure and swelling
• Best engine cooling impeller
• Stable pressure
• Exact dimensions
• Used by leading manufacturers
Specials Closeouts Remanufactured Rebates
|
|
|
CAL PUMPS
A/C Circulation Pump - Air Conditioning & Cooling - Air Conditioning - Seawater Circulation Pump - Magnetic Drive Small Pond Pump
CAL customers rely on our stainless steel and bronze pumps, and once you've owned one, you'll know why. Four different models are offered at CLR Marine with flow rates from 320 gph to 1,200 gph cover a wide variety of uses. All pumps in this series come with a one-year warranty and will provide trouble free use in fresh or salt water. You can even use it in hot water up to 110°F!
6' power cords are standard.
Features & Benefits of the CAL PUMPS:
One year warranty
UL Listed for consumer confidence
Premium stainless steel and bronze construction for longevity
Six or twenty foot power cord for convenience
Suitable for fresh or salt water applications
Can be used in hot water applications up to 110°F
Extremely quiet operation
Use submerged or in open air
Corrosion resistant
115 or 220 volt motors
Thermally protected
Optional Mounting Bracket Available (model MSUB OR MSUBM)
Do Not Run Dry
Operate horizontal or volute down
MS320 have ½” MNPT intake and ¼” MNPT discharge
MS580, 900, 1200 have ¾” MNPT intake and ½” MNPT discharge
Cal 1200 GALLON PER HOUR PUMP W/ 6' CORD
Model: MS1200
Cal 900 GALLON PER HOUR PUMP W/ 6' CORD
Model: MS900
Cal 580 GALLON PER HOUR PUMP W/ 6' CORD
Model: MS580
Cal 320 GALLON PER HOUR PUMP W/ 6' CORD
Model: MS320
See all Cal Pump Products
S T A I N L E S S S T E E L & B R O N Z E P U M P S
Model
AMPS
(MIN/MAX)
WATTS
(MIN/MAX)
MAX
FLOW
MAX
HT.
1'
3'
5'
7'
9'
11'
13'
15'
17'
MS320
1.05-1.30
68-89
375
12.7'
360
335
305
262
215
-
-
-
-
MS580
2.15-2.55
138-203
860
14'
830
750
675
580
475
345
125
-
-
MS900
2.17-2.76
156-234
885
16'
855
790
725
650
560
460
350
175
-
MS1200
2.97-3.79
208-312
1100
18'
1070
1000
925
850
760
675
560
425
225
Cal Pumps at CLR Marine
|
|
|
Express® Mach3™ - Right Hand - Stainless Steel Propeller - EX1/EX2-1319 - 3-Blade - 13.25" x 19 Pitch
Utilizing almost 40 years of race boat and high performance prop design expertise, our Express® Mach3™ series of props captures all the best techniques and technologies available to get the most out of your boat. Aggressive pitch angles, radical designs, sharp cup profiles. These three blade propellers excel at achieving maximum speed, while delivering Best-in-Class handling and acceleration. Hole Shot? Got it, and hang on! Cornering? We've got that, too! Top Speed? We say "No Faster Prop on the Water" for a reason!
Upgrading your current propeller from aluminum to stainless steel, or from an old generation design to the latest technology, Express Mach3 Propeller is the best investment in boat improvement you can make. Today's Designs will run circles around the competition, and can make dramatic improvements in boat performance. The gain in fuel economy can often pay for the cost of a new propeller in one or two seasons, making it a sound investment in your time on the water.
Proprietary Stainless Steel, TP17™
Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat.
Large Free Flowing Exhaust Ports
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.
Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
317.74 |
|
|
Express® Mach3™ - Right Hand - Stainless Steel Propeller - EX1/EX2-1321 - 3-Blade - 13.25" x 21 Pitch
Utilizing almost 40 years of race boat and high performance prop design expertise, our Express® Mach3™ series of props captures all the best techniques and technologies available to get the most out of your boat. Aggressive pitch angles, radical designs, sharp cup profiles. These three blade propellers excel at achieving maximum speed, while delivering Best-in-Class handling and acceleration. Hole Shot? Got it, and hang on! Cornering? We've got that, too! Top Speed? We say "No Faster Prop on the Water" for a reason!
Upgrading your current propeller from aluminum to stainless steel, or from an old generation design to the latest technology, Express Mach3 Propeller is the best investment in boat improvement you can make. Today's Designs will run circles around the competition, and can make dramatic improvements in boat performance. The gain in fuel economy can often pay for the cost of a new propeller in one or two seasons, making it a sound investment in your time on the water.
Proprietary Stainless Steel, TP17™
Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat.
Large Free Flowing Exhaust Ports
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.
Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
317.74 |
|
|
Express® Mach3™ - Right Hand - Stainless Steel Propeller - EX-1419 - 3-Blade - 14.25" x 19 Pitch
Utilizing almost 40 years of race boat and high performance prop design expertise, our Express® Mach3™ series of props captures all the best techniques and technologies available to get the most out of your boat. Aggressive pitch angles, radical designs, sharp cup profiles. These three blade propellers excel at achieving maximum speed, while delivering Best-in-Class handling and acceleration. Hole Shot? Got it, and hang on! Cornering? We've got that, too! Top Speed? We say "No Faster Prop on the Water" for a reason!
Upgrading your current propeller from aluminum to stainless steel, or from an old generation design to the latest technology, Express Mach3 Propeller is the best investment in boat improvement you can make. Today's Designs will run circles around the competition, and can make dramatic improvements in boat performance. The gain in fuel economy can often pay for the cost of a new propeller in one or two seasons, making it a sound investment in your time on the water.
Proprietary Stainless Steel, TP17™
Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat.
Large Free Flowing Exhaust Ports
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.
Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
354.18 |
|
|
Express® Mach3™ - Right Hand - Stainless Steel Propeller - EX-1421 - 3-Blade - 14.25" x 21 Pitch
Utilizing almost 40 years of race boat and high performance prop design expertise, our Express® Mach3™ series of props captures all the best techniques and technologies available to get the most out of your boat. Aggressive pitch angles, radical designs, sharp cup profiles. These three blade propellers excel at achieving maximum speed, while delivering Best-in-Class handling and acceleration. Hole Shot? Got it, and hang on! Cornering? We've got that, too! Top Speed? We say "No Faster Prop on the Water" for a reason!
Upgrading your current propeller from aluminum to stainless steel, or from an old generation design to the latest technology, Express Mach3 Propeller is the best investment in boat improvement you can make. Today's Designs will run circles around the competition, and can make dramatic improvements in boat performance. The gain in fuel economy can often pay for the cost of a new propeller in one or two seasons, making it a sound investment in your time on the water.
Proprietary Stainless Steel, TP17™
Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat.
Large Free Flowing Exhaust Ports
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.
Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
354.18 |
|
|
Express® Mach3™ - Right Hand - Stainless Steel Propeller - EX-1415 - 3-Blade - 15" x 15 Pitch
Utilizing almost 40 years of race boat and high performance prop design expertise, the Express Mach3 series of props captures all the best techniques and technologies available to get the most out of your boat. Aggressive pitch angles, radical designs, sharp cup profiles. These three blade propellers excel at achieving maximum speed, while delivering Best-in-Class handling and acceleration. Hole Shot? Got it, and hang on! Cornering? We've got that, too! Top Speed? We say "No Faster Prop on the Water" for a reason!
Upgrading your current propeller from aluminum to stainless steel, or from an old generation design to the latest technology, Express Mach3 Propeller is the best investment in boat improvement you can make. Today's New Designs will run circles around the competition, and can make dramatic improvements in boat performance. The gain in fuel economy can often pay for the cost of a new propeller in one or two seasons, making it a sound investment in your time on the water.
Proprietary Stainless Steel, TP17™
Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat.
Large Free Flowing Exhaust Ports
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.
Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
354.18 |
|
|
Express® Mach3™ - Left Hand - Stainless Steel Propeller - EX-1415-L - 3-Blade - 15" x 15 Pitch
Utilizing almost 40 years of race boat and high performance prop design expertise, the Express Mach3 series of props captures all the best techniques and technologies available to get the most out of your boat. Aggressive pitch angles, radical designs, sharp cup profiles. These three blade propellers excel at achieving maximum speed, while delivering Best-in-Class handling and acceleration. Hole Shot? Got it, and hang on! Cornering? We've got that, too! Top Speed? We say "No Faster Prop on the Water" for a reason!
Upgrading your current propeller from aluminum to stainless steel, or from an old generation design to the latest technology, Express Mach3 Propeller is the best investment in boat improvement you can make. Today's New Designs will run circles around the competition, and can make dramatic improvements in boat performance. The gain in fuel economy can often pay for the cost of a new propeller in one or two seasons, making it a sound investment in your time on the water.
Proprietary Stainless Steel, TP17™
Formulated to meet the exacting requirements of the New Express Mach3 and Mach4 designs. 20% higher chromium content than the competition - more shine, better corrosion resistance. Almost 250% Stronger and 5X more durable than run-of-the-mill stainless steel. This new material allows Turning Point's Engineers and Designers the freedom to produce radical new designs that will help you wring the most performance out of your boat.
Large Free Flowing Exhaust Ports
Turning Point's Propeller Housings have massive Exhaust flow pathways. Their Propellers have 40% more exhaust flow Area versus competitive product. More exhaust flow and less backpressure can generate more horsepower. Like headers for your boat.
Turning Point manufactures Express propellers to fit 9.9(bigfoot)-300+hp Evinrude®, Force®, Honda®, Johnson®, Mariner®, Mercruiser®, Mercury®, Nissan®, OMC®, Parsun®, Suzuki®, Tohatsu®, Volvo® Penta®, and Yamaha® Outboards and Sterndrives. Choose one of our Lifetime Warranty MasterGuard Installation Kits to fit your engine, then choose the propeller that matches your boating requirements. There are 3 and 4 blade, left and right rotation prop models with a variety of diameter and pitch options available for almost all boat types. Turning Point's Props Run Faster, Pull Harder, and Handle Better.
Note: A Hub Kit is required for installation of this propeller. See the Turning Point Selection Chart or the Prop Wizard™ for hub kit selection.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
354.18 |
|