Fuel Flow Sensor 8-10 LPM/2.1-18.5 GPM When fluid passes through the sensor, the rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from these sensors are transmitted to the FFM100 which performs flow rate calculations based on the received pulses. Specifications: Construction: Housing Material Aluminum Port Size: 3/4" NPT Female Maximum Viscosity: 1000 cPs Strainer Size: 60 Mesh (If not already installed after fuel filter) WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Sierra Marine Engine Parts & Drive Parts   Sierra Marine is a trusted name in aftermarket replacement boat engine and drive parts. Sierra’s products are designed and engineered to exceed the high horsepower demands of today’s engines in the harshest marine environments. All Sierra products meet or exceed the original equipment part it replaces.   If you need help finding a part, we need, Make, Model, Year, Horsepower, and Serial number of your engine.   Warning: We can no longer ship engine parts International or to California Due to Prop 65.

Fuel Flow Sensor 10-100 LPM/2.6-26.4 GPM When fluid passes through the sensor, the rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from these sensors are transmitted to the FFM100 which performs flow rate calculations based on the received pulses. Specifications: Construction: Housing Material Aluminum Port Size: 1" NPT Female Maximum Viscosity: 1000 cPs Strainer Size: 60 Mesh (If not already installed after fuel filter) WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Fuel Flow Sensor with 10' cable & T-connector Fuel Flow Sensor Gasoline ONLY. 1 required per engine. Up to 3 engines supported. Outputs: Fuel Flow Tank Fuel Used Trip Fuel Used Seasonal Fuel Used Cable Length: 10' Fuel Line Diameter: 3/8" (9.5mm) Inside Diameter Flow Rate Measured: Optimized for 0.6-45 Gal/hr but can measure outside these values Added Back Pressure to the fuel system: 0.5 PSI at 20 Gal/hr; 1 PSI at 40 Gal/hr Installation Location: Above the max level of the fuel tank, in-line after the fuel filter and any Y's or T's in the line Package: The Fuel Flow Sensor, N2K T and 2 (two) 1" hose clamps Fuel Type: Gasoline only. The Fuel Flow Sensor does not operate diesel engine fuel systems Hole required to route through a bulkhead: 22mm (7/8") Multiple Fule Flow sensors possible: Yes

Johnson 10-24119-2 Pump for Perkins 4.108/4.236 Pump Body: Bronze Ports: 3/4" Threaded Cam: Full Thickness Standard Impeller: Neoprene Standard Shaft Seal: Lip Type Drive: Flange Mounted to Engine   The 10-24119-2 shaft coupling extends .70" past flange  

Johnson 10-24239-2 Brz Eng Cooling Pump  

BURKS GA6-1.5MV-5-11/16, PUMP END ONLY with VITON SEAL UNSPSC Code: 40150000

BURKS GNA6-1 1/4-5.00, CENTRIFGUAL PUMP ONLY BRONZE-FIT Bronze Fitted Cast Iron Construction. Base mounted Pump Only less Motor. Ports are Inches NPT Inlet, Inches NPT Outlet.   UNSPSC Code: 40150000

304 Stainless Steel Strainer Basket Only Size 10 for 2-1/2" Strainer Features: Stainless steel Replacement basket for intake strainer Diameter: 2-1/2"

Ampco Pumps KC2 2 1/2 X 2 Fluid End Nialbz 5.00" Trim

Sierra fuel water separators remove over 98.8% of emulsified water from gasoline. Sierra's 10 micron filters are over 90% efficient at removing particles as small as 10 micron. All filters flow at 90 GPH. 10 micron filters are recommended to prevent damage to inboard and outboard fuel injection systems. Kits include two brass pipe plugs. Display packaged.

Johnson Raw Water Pump for 4-Cylinder AQ Series Volvo Johnson Seawater Pump fits Early 4-Cylinder Volvo-Penta AQ125, 131, 145 pump for 4-cylinder engines. Replaces Volvo-Penta part # 855578

Hide all engine cables, hoses and harnesses. Can be added to any style outboard. Kit contains 2" flange and 5' of 2" Sternflex Hose.

BURKS 9762-1, SEAL 5/8 VITON UNSPSC Code: 40150000

Scot Pump 913-VL 10 VENTED LOOP 1" The Vacuum Breaker has a normally closed poppet which keeps vent line fumes from the vessel. The breaker is designed for a corrosion proof service life with a protected air vent. All of the parts exposed to liquid are manufactured from Delrin. The external poppet spring is stainless steel. Liquid never touches the stainless steel spring.   The vacuum breaker has a low vacuum breakaway.   Pressure on the inside of the loop keeps the breaker closed. The soft, resilient seat gives quiet, trouble-free operation. The spring action provides a quiet opening and closing operation. Air goes in – never out.    • Type 316 Stainless Steel Loop with Vacuum BreakerStandard SAE ( Society ofAutomotive Engineers) Hose Barb on each end. • Use for Heads, Bilge Pumps, Shower Pumps, and Engine Exhaust Lines • Sizes 1/2 inch to 2 inches • All head flushing water and discharge lines, engine wet exhaust lines, and bilge pump lines should have a vented loop. • Use on marine heads, engine cooling systems, and bilge pumps.