|
Universal Mast Mount Platform for 12"18" Radome
Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast.
Adjustable
Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast.
Incredible Strength
The solid under body construction not only greatly improves strength but also hides radar cables. On certain models.
Accessories
Pre-drilled under body allows for flood lights or horns to be mounted on certain models.
Compatible Manufacturers:
Furuno
JRC
Koden
Lorenz
Sitex
VDO
|
374.40 |
|
|
Universal 24" Radar Mast Platform
Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast.
Adjustable
Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast.
Incredible Strength
The solid under body construction not only greatly improves strength but also hides radar cables. On certain models.
Accessories
Pre-drilled under body allows for flood lights or horns to be mounted on certain models.
Compatible Manufacturers:
Furuno
Garmin
JRC
Koden
KVH
Raymarine
Simrad
Sitex
|
388.80 |
|
|
18" Radar Mast Platform
Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast.
Adjustable
Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast.
Incredible Strength
The solid under body construction not only greatly improves strength but also hides radar cables. On certain models.
Accessories
Pre-drilled under body allows for flood lights or horns to be mounted on certain models.
Compatible Manufacturers:
B&G
Garmin
Humminbird
Lowrance
Raymarine
SImrad
|
360.00 |
|
|
Universal Masthead Mount
Extend your WindTrak 10.Sport or WindTrak 15 vane away from masthead obstructions and turbulence. The 13" (33 cm) arm comes with hardware allowing side or top mounting and offset angles up to ±20 degrees. May be attached securely to flat, curved, vertical, horizontal, or inclined surfaces. Gain space aloft and improve mounting position of wind finders and other equipment. Mount on the back of the mast for easier viewing from the cockpit. The mount adapts to virtually every masthead situation.
Features:
Length 13" (33 cm)
Weight 3.2 oz (90 g)
Boom can be shortened if necessary; complete instructions included
Can be used with WindTrak Light #3200. Also accommodates Davis J-Base Mounts (using #10 stainless steel screws and nuts, not included)
|
37.50 |
|
|
Universal X-Grip Holder f/12" Tablets
The new RAM X-Grip line of products just got bigger and better. This new model is just what you've been looking for to hold your favorite tablet. Just like the devices it was made for, it is everything you need and nothing you don't. Simple to open and close, the spring loaded RAM X-Grip leaves the outside edge of your tablet almost completely free of annoying obstructions. Soft rubber fingers apply just enough force to keep your tablet in safe and secure. Compatible with a wide range of mounting solutions, your tablet is sure to find a home no matter where your travels take you.
The RAM-HOL-UN11U holder expands and contracts for perfect fit of most 10" and 12" tablets with or without sleeves, as well as some smaller tablets. This holder by RAM consists of a composite spring loaded holder, expandable grip arms and additional bottom support keeper.
** The RAM-HOL-UN11U is compatible with the iPad Pro WITHOUT CASE ONLY. **
Compatible Devices (WITH OR WITHOUT CASE):
Microsoft Surface Pro 3
Samsung Galaxy Note® Pro 12.2
Most 12" Screen Tablets
X-Grip Holder Dimensions:
Minimum Width = 7.25"
Maximum Width = 8.75"
Maximum Length (WITHOUT additional supports) = Unlimited
Maximum Length (WITH additional supports) = 10.25"
Depth = 0.875"
X-Grip Holder Features:
Spring loaded cradle expands and contracts for perfect fit of your tablet
Rubber coated tips will hold your tablet firm and stable
Versatility of cradle allows for attachment to many 1" socket mounts
Socket technology allows for multiple adjustment angles and articulation of your tablet
Easy access grip knobs, located on the back of the cradle for quick release of your tablet
Multiple mounting access points on the back of the cradle
Additional support keeper at the bottom of the cradle
Full access to all ports
Lifetime warranty
Made in the U.S.A.
Material:
Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite
Note:
The "U" in the part number reflects product packaged in poly bag.
|
74.69 |
|
|
Dual Articulating Suction Cup w/Medium Length Double Socket Arm & Universal X-Grip® Cradle f/12" Large Tablets
The RAM-B-189-PIV1-UN11U consists of a dual articulating 3.3" twist lock suction cup base, double socket arm, and universal X-Grip® cradle for 12" Tablets. The dual articulating suction cup base is an amazing innovation in suction cup mounting. With the ability to independently articulate each suction cup, this mounting base can be used in a variety of applications such as curved windows and surfaces. Included are extra easy access grip knobs, located on the back of the cradle for quick release of your tablet.
The X-Grip® cradle is compatible with devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size.
Cradle Dimensions:
Minimum Width = 7.25”
Maximum Width = 8.75”
Maximum Length (WITHOUT additional supports) = Unlimited
Maximum Length (WITH additional supports) = 10.25”
Depth = 0.875"
Features:
Material: High Strength Composite & Powder Coated Marine Grade Aluminum
Ball Size: 1" Rubber Ball "B" Size
Note: The "U" in the part number reflects product packaged in poly bag.
Weight: 2.45 lbs.
*The RAM-HOL-UN11U is compatible with the iPad Pro WITHOUT CASE ONLY.
|
141.55 |
|
|
Mast Mount Bracket for UFO X TV Antenna
High quality, stainless steel bracket specifically designed for the UFO X mast mounting. This pole has been designed mainly for the Majestic UFO when mounting on masts to allow the antenna to be easily fitted. Simply install the bracket to the side of the mast and then screw the antenna to the top height near the top of the mast. This will assist in getting the best possible signal.
|
30.62 |
|
|
GP2524 SystemPod Pre-Cut for Raymarine eS75/eS77/eS78 Mounted Center for 12" Wide Guard
GP2500 Series for 12" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic.
A SystemPod is best mounted on a Single Bend AngleGuards.
SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications.
All SystemPods include
Acrylic capped ABS plastic
Chromed stainless steel tamper-poof fasteners
Double seal for watertight integrity
Models are available pre-cut for popular electronics
Stainless steel mounting hardware and mounting gaskets
*See Literature tab for an image with dimensions
|
331.62 |
|
|
23.75" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Separately
|
1512.00 |
|
|
13.25" Pre-Drilled Dual Mount for Most Closed Dome Radars - Black - Top Plate Required
Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management.
Compact Design
Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.
Eliminate Interference
A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation.
Universal
The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.
Modular Top Plate
The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.
*Top Plate Sold Separately
|
1032.00 |
|
|
SM-18-A
Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast.
Adjustable
Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast.
Incredible Strength
The solid under body construction not only greatly improves strength but also hides radar cables. On certain models.
Accessories
Pre-drilled under body allows for flood lights or horns to be mounted on certain models.
Compatible Units:
Intellian - i4 & i4P
KVH - M5, FB250(18"), TV5
Raymarine - 45STV
Sea Tel/Cobham - ST14, FX150 (16.5")
VDO - Ocean Line 337
|
489.60 |
|
|
Mast Platform for KVH M7/TV6 & Intellian i6/D6
Seaview Mast Mounts are designed to have the radar or satdome as close as possible to the mast. Ultra heavy duty mounting feet and rivets are used to secure the Mast Mount to the mast.
Adjustable
Designed with fore and aft adjustable rails so that you can have the radar as close as possible to the mast.
Incredible Strength
The solid under body construction not only greatly improves strength but also hides radar cables. On certain models.
Accessories
Pre-drilled under body allows for flood lights or horns to be mounted on certain models.
Compatible Units:
Glomex - 20"-27" satdomes
Intellian - i5, i6, i6P, S6HD, FB500 and v45C
JRC - JUE 500 (24")
KVH - M7, M7SK, FB500(26"), V7, V7-IP, TV6, HD7 and TV3-IP(24")
Oyster - 50MGS, 75MGS, 77MGS and TRX-7MGS
Raymarine - 60STV
Seatel / Cob Ham - C18 & FX250 (24")
Thrane & Thrane - Sailor FB500 & Fleet 55+
VDO - Ocean Line 345, 360, 445 and 460
|
676.80 |
|
|
The Mast Mount is designed to fit multiple specific manufacturers Radomes and Satellite Antennas. It is constructed from lightweight aluminum and is powder-coasted white for a durable finish. For fast and accurate installation Edson designed mounting feet that can be properly secure to a wide range of mast profiles. One Mounting Plate is required to complete the Edson Vision SeriesMast Mount System.
Features:
Rugged Design
Marine-grade aluminum construction
Powder-coated white
Rivets included for mast attachment
Easy installation
First all modular system - extremely versatile
Simple selection and installation
Requires Vision Mounting Plate to install radar or sat dome antenna
Mast Mount Radar Platform
For sailboats and trawlers
Swivel Feet fit most masts
Rivets included
|
484.20 |
|
|
Mast Mounts
Compatible Units:
Raymarine: 24" 4kW Radome
Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts.
Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation.
Features
Easy and quick to install with all fastenings supplied
Attached to mast by four swivel feet matching the profile of any mast
12 point fixing using highest quality Monel rivets for a secure installation
Nylon washers for all fastenings to protect paint finish
Waterproof cable grommet included to seal cable entry into mast
Materials
Marine grade 6082 aluminium
Polyester powder coated for a durable and gloss white finish
Kit includes
1 x Mast Mount
|
417.83 |
|
|
Mast Mounts
Compatible Units:
Raymarine: 2kW Radome
Fantom 24 GMR24HD / 24xHD
Still the first choice for boat owners the world over, Scanstrut Mast Mounts are the ultimate solution for mounting radars on yachts masts.
Raising the antenna clear of any obstructions or interference, the mast mount is a classic and reliable installation.
Features
Easy and quick to install with all fastenings supplied
Attached to mast by four swivel feet matching the profile of any mast
12 point fixing using highest quality Monel rivets for a secure installation
Nylon washers for all fastenings to protect paint finish
Waterproof cable grommet included to seal cable entry into mast
Materials
Marine grade 6082 aluminium
Polyester powder coated for a durable and gloss white finish
Kit includes
1 x Mast Mount
4 x Swivel mounting feet
1 x Complete fastening pack
|
367.87 |
|