Hi-Water Bilge Alarm The High Water Bilge Alarm consists of a non-mercury float switch and an in-dash gauge that features both a visual and an audible 85 db alarm. This unit allows an unmanned com part ment to be constantly monitored. For additional compartments add additional Rule Float Switches. Complies with CFR 182.530 which requires a visual and audible alarm in each unmanned space on commercial vessels at least 26' (7.9m) in length. WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

High Water Bilge Alarm with Switch & Gauge - 24V Using a compact float switch and dash mounted alarm, Rule provides boaters with a warning to high bilge water levels. Ideal for larger yachts and commercial vessels larger than 26' with unmanned compartments that have to comply with CFR 182.530. A bright LED indicator light provides a visual alarm when ambient noise levels exceed alarm volume. Constantly monitor your bilge for water and stay compliant to Coast Guard regulations with a Hi-Water Bilge Alarm from Rule. Features: Visible and audible alarm to monitor bilge water levels Includes mercury-free float switch and dash mounted alarm Complies with CFR 182.530 24V WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

The Environmental Protection Agency published a final rule aimed at reducing exhaust emissions from diesel-powered recreational boats.   The National Marine Manufacturers Association says the rule helps the marine industry avoid “a series of very detrimental after treatment catalyst-based standards.”   As originally proposed, the rule, “Control of Emissions of Air Pollution from Locomotive Engines and Marine Compression Ignition Engines Less Than 30 Liters Per Cylinder,” would have required U.S.-flagged recreational marine diesel-powered vessels with engines greater than 2000 kW to install catalyst after treatment systems.   “This rule had the potential to very severely impact recreational yacht builders,” said John McKnight, the NMMA director of environmental safety and compliance, in a statement. “Once a rule like this gets on the books and the technology is required, it could spread to all vessels operated within U.S. waters, regardless of horsepower or where the vessel is flagged.”   A diesel catalyst system requires urea, a chemical made from ammonia and carbon dioxide and low-sulfur fuel. Urea is not necessarily suitable for storage on a recreational yacht, nor is it widely available, according to McKnight. He says the lack of availability of urea ultra-low sulfur fuel in many foreign ports that luxury yachts frequent could have severely compromised the value of U.S.-flagged vessels.   “The major flaw in EPA's proposal was that the rule only applied to U.S. flagged vessels,” McKnight said. “We were able to convince the agency that the rule, as proposed, would only encourage more yacht owners to flag their vessels outside the U.S.”   In the final rule, the EPA exempted recreational yachts from Tier IV catalyst-based standards. The final rule instead requires engine manufacturers to meet the more stringent Tier III requirements; however, McKnight says this requirement will be transparent to yacht builders.   Despite this key regulatory accomplishment, McKnight warns yacht manufacturers to remain cautious.   The International Marine Organization's Marine Protection Committee released a proposal April 4 requiring aftertreatment on all recreational and commercial diesel marine engines greater than 750 hp. The NMMA is working with the ICOMIA Marine Engine Committee and the European Association of Internal Combustion Engine Manufacturers to oppose this proposal.   IMO would only require a recreational yacht traveling to ports within countries that signed a treaty with the organization to be equipped with aftertreatment; however, the significance of the proposal is that countries that have signed IMO treaties encompass a majority of the well-traveled world.   To date, the United States has not signed a treaty with IMO. If, however, the proposed IMO rule is finalized as is, the EPA is expected to move quickly to adopt aftertreatment standards.   For information about the latest EPA rule or the IMO proposal, contact John McKnight at (202) 737-9757 or jmcknight@nmma.org.

1842 M2 OLED Digital Bilge Meter The M2 Organic LED Digital Monitor measures essential electrical system parameters with adjustable alarms and an auto-dimming display. The M2 Monitors include a MOSFET External Circuit Relay (ECR) which can be used to control external circuits based on any value measured by the M2. Features: Auto-dimming, bright Organic LED display is easy to read 80dB alarm on all models Isolated 500mA MOSFET relay Bilge float switch not included Specifications: Meter: Bilge Function: Monitors up to 4 bilges Alarm/Relay Activation: Run time/hr Cycles/24 hr Average Cycles Display Size: 55mm x 28mm Input Voltage: 7-70V DC Range: 0.3W-1.0W WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Bilge Boat Monitor System - 12/24V A complete monitoring system that provides you with real time data to your smartphone or your computer such as bilge water level alarm, battery status, positioning/tracking alarms if your boat is being moved and more! Easy to install, suitable for virtually any floating vessel with 12/24 V DC power onboard. Features: SIM card that works with all international GSM communication standards with outstanding connectivity; optional use your own SIM card. Latest technology and designed for marine use, robust and very compact. Built-in battery allows the device to continue to send information over a period of time if the power is cut. IPX6 water protected and withstands rough movements at sea. Approved by international insurance companies. CE and FCC certified *Reduce your insurance costs up to 20% by having an approved high-water alarm and positioning system installed onboard

360GPH Standard Bilge Pump - 12V Customers talk about flow, they want the water out of the bilge, and fast. Improved design and performance means that our next generation 360GPH pump will produce this flow at just 12V rather than 13.6V as previously required...more typical of on board voltage supply. Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it. We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot. We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting started Features: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

500GPH Standard Bilge Pump - 12V Customers talk about flow, they want the water out of the bilge, and fast. Improved design and performance means that our next generation 500GPH pump will produce this flow at just 12V rather than 13.6V as previously required...more typical of on board voltage supply. Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it. We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot. We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting started Features: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

500GPH Standard Bilge Pump - 24V Customers talk about flow, they want the water out of the bilge, and fast. Improved design and performance means that our next generation 500GPH pump will produce this flow at just 24V rather than 27.2V as previously required...more typical of on board voltage supply. Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it. We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot. We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting started Features: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

800GPH Standard Bilge Pump - 12V Customers talk about flow, they want the water out of the bilge, and fast. Improved design and performance means that our next generation 800GPH pump will produce this flow at just 12V rather than 13.6V as previously required...more typical of on board voltage supply. Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it. We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot. We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting started Features: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

800GPH Standard Bilge Pump - 24V Customers talk about flow, they want the water out of the bilge, and fast. Improved design and performance means that our next generation 800GPH pump will produce this flow at just 24V rather than 27.2V as previously required...more typical of on board voltage supply. Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it. We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot. We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting started Features: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

1100GPH Standard Bilge Pump - 12V Customers talk about flow, they want the water out of the bilge, and fast. Improved design and performance means that our next generation 1100GPH pump will produce this flow at just 12V rather than 13.6V as previously required...more typical of on board voltage supply. Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it. We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot. We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting started Features: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

1100GPH Standard Bilge Pump - 12V Customers talk about flow, they want the water out of the bilge, and fast. Improved design and performance means that our next generation 1100GPH pump will produce this flow at just 24V rather than 27.2V as previously required...more typical of on board voltage supply. Our next generation of Rule pumps include check valves and to do this, we've created hidden air vent to prevent airlocking. Under each strainer tab there is a small hole that vents any air trapped in the pump housing preventing airlocks...and that's how we do it. We have true electromagnetic suppression (EMC). We have a built-in thermal cell that protects the pump and the vessel when things get too hot. We've re-engineered the inside and outside of our bilge pumps, starting with a blank slate. And we're just getting started Features: Non-automatic - used with a panel switch or Rule float switch Submersible and Ignition Protected High efficiency, low amp motor Stainless-steel shaft Includes backflow preventer WARNING: This product can expose you to chemicals including 1,3-Butadiene which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

LoPro 900GPH Bilge Pump - Automatic The Rule LoPro™ 900 Automatic is a fully automatic low profile Bilge Pump with a 900 gallons per hour capacity. Designed for tight spaces, the height of the pump is only 2-1/4". It features a threaded discharge nozzle to which you can attach either a straight or a 90° fitting (included). In addition, you may use the tricuspid check valve (included) on the straight fitting to minimize the back flow of water. The entire discharge body swivels up to 180° for ease of installation. The hose attached can also swivel 360° to route the hose perfectly. The pump features a sensing switch to control the pump. Unique to this pump are two settings, a high setting where the pump turns on when the water reaches 1-3/4" and a low setting where the pump turns on when the water reaches 1". Features: 900 GPH Low Profile Bilge Pump Fits into hard to reach places Fully Autuomatic- two settings available, high and low Threaded discharge ports with mulitiple fittings available Features a tricuspid check valve to minimize back flow of water 3 Year Warranty WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

LoPro 900GPH Bilge Pump - Non-Automatic The Rule LoPro™ 900 non-automatic is a low profile Bilge Pump with a 900 gallons per hour capacity. Designed for tight spaces, the height of the pump is only 2-1/4". It features a threaded discharge nozzle to which you can attach either a straight or a 90° fitting (included). In addition, you may use the tricuspid check valve {included} on the straight fitting to minimize the back flow of water. The entire discharge body swivels up to 180° for ease of installation. The hose attached can also swivel 360° to route the hose perfectly. Features: 900 GPH Low Profile Bilge Pump Fits into hard to reach places Non-automatic, requires float and or panel switch to automate Threaded discharge ports with mulitiple fittings available Features a tricuspid check valve to minimize back flow of water WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Rule 3700 Automatic 12v Heavy duty construction for both commercial and pleasure boat use; known for trouble free operation and reliability. 1-1/2" (38mm) discharge outlet. WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.