|
Rule In-Line Blower - 4" Ducting
Part Number: 240
Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule® in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets.
Features
Efficient high-volume air flow
Quiet operation
Low amp draw
Slip-on inlet and outlet ducting connections
Sealed motor shaft for moisture protection
Corrosion resistant nickel-plated motor housing
IMCI (CE)
USCG 183.410 Compliant: Ignition protected
Applications:
Race cars and helmet ventilation
Bus ventilation (engine and bathroom fumes)
Prison van ventilation (cooling, air-freshening)
Blow-up signs and mascots
Tanning booths
Building ventilation
Specifications
Approvals: CE
Dimensions (H x W x D): 102 x 152 x 106 (mm)
ElectricalCharacteristics: 4.3 Amp
Flow Rate (US gallons & litres): 235 CFM @ Open Flow
Fuse Size: 7 (amp)
Product Inlet Fitting: 4" (102 mm) Ducting
Product Outlet Fitting: 4" (102 mm) Ducting
Voltage: 13.6 (Vdc)
WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
42.97 |
|
|
4" In-Line Blower
Inlet/Outlet - 4"
CFM - 240
Johnson Pump in-line blowers provide ventilation for bilges, engine compartments, galleys, and heads.
Made from high quality ABS plastic construction, corrosion resistant motors, and premium electrical connections completes these blowers
Five blade, quiet, highly efficient, and reliable operation will provide years of long life
Compact and with mounting feet makes it easy to install on any flat surface
|
44.45 |
|
|
Rule In-Line Blower - 3" Ducting
Part Number: 140
Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule? in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets.
Features
Efficient high-volume air flow
Quiet operation
Low amp draw
Slip-on inlet and outlet ducting connections
Sealed motor shaft for moisture protection
Corrosion resistant nickel-plated motor housing
IMCI (CE)
USCG 183.410 Compliant: Ignition protected
Applications:
Race cars and helmet ventilation
Bus ventilation (engine and bathroom fumes)
Prison van ventilation (cooling, air-freshening)
Blow-up signs and mascots
Tanning booths
Building ventilation
Specifications
Approvals: CE
Dimensions (H x W x D): 76 x 127 x 81 (mm)
ElectricalCharacteristics: 2.9 Amp
Flow Rate (US gallons & litres): 135 CFM @ Open Flow
Fuse Size: 4 (amp)
Product Inlet Fitting: 3" (76 mm) Ducting
Product Outlet Fitting: 3" (76 mm) Ducting
Voltage: 13.6 (Vdc)
WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
39.28 |
|
|
3" In-Line Blower
Inlet/Outlet - 3"
CFM - 158
Johnson Pump in-line blowers provide ventilation for bilges, engine compartments, galleys, and heads.
Made from high quality ABS plastic construction, corrosion resistant motors, and premium electrical connections completes these blowers
Five blade, quiet, highly efficient, and reliable operation will provide years of long life
Compact and with mounting feet makes it easy to install on any flat surface
|
42.96 |
|
|
Turbo 4000 Series II In-Line Blower
Part #: 1749-4
Attwood's improved Turbo 4000 Series II sets the standard for in-line blower performance. Utilizing advanced fan blade design techniques, Attwood has developed a blower system that matches air flow of existing in-line blowers at a significantly reduced noise level. The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size.
Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads.
Features:
Nickel-plated motor can for corrosion resistance
Stiffening ribs to reduce housing distortion
Motor cap to seal wires and motor for water resistance
Five-blade fan maximize airflow and efficiency
Tabs in intake and exhaust hold ventilation hose/clamp firmly in place
Low amp draw motor for longer blower and battery life
Built-in mounting feet allow easy vertical or horizontal install
3-Year Warranty
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
29.63 |
|
|
Turbo 3000 Series In-Line Blower
Part #: 1733-4
The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size.
Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads with optional MP1 molded rubber connectors. Improved 3" design.
Features:
Nickel-plated motor can for corrosion resistance
Stiffening ribs to reduce housing distortion
Motor cap to seal wires and motor for water resistance
Five-blade fan maximize airflow and efficiency
Tabs in intake and exhaust hold ventilation hose/clamp firmly in place
Low amp draw motor for longer blower and battery life
Built-in mounting feet allow easy vertical or horizontal install
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
25.88 |
|
|
iL200 In-Line & Submersible Pump 12V
Centrifugal submersible and inline pump;
Suitable for fresh or salt water
Water transfer, deck shower, or deck wash
Water Systems to 60°C
Intermittent rating of 20 minutes. Should not be run dry for long periods
Specifications
Output: up to 12.7 litres/minute at up to 1bar (2.8 gallons/minute at 14psi)
Connections: 1/2" (12.7mm) and 3/4" (19mm) Hose
Dimensions: (L x Diameter) 130 x 36 (mm)
Amp Draw: 2.8 (amp)
Packed Size: 190.0 x 50.0 x 130.0 mm (LxHxW)
Weight: 206 (g)
WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
28.75 |
|
|
V-Jam Cleat - Stainless Steel - 6mm(1/4") Max Line Size
A stainless steel jam cleat useful for jamming small diameter, low load lines. Ideal for dinghy halyards and outhauls, flag halyards, etc
|
15.24 |
|
|
In-Line 3" Bilge Blower - 24V
Features:
Connections: - for 75mm (3") ducting
Dimensions: - 130mm long, 95mm high, 125mm wide
Fuse Size: - 2.5(amp)
Output: - 3.8 cu. m/minute
Efficient high volume airflow
Quiet running
Slip-on inlet and outlet ducting connections
Made in corrosion-resistant materials
Mounts in any position on any flat surface
Low current draw
Packaged Dimensions: L:15.00 x H:12.00 x W:13.00cm
Actual Weight: 0.54 Kg (Approx. 0.79 Kg packed)
WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
39.11 |
|
|
Air Blower 1000 Inline 165 - 12V
7″ in-line mounted marine ventilation 12V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 165mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance.
Features:
Weight: 1.2 kg/2 lbs
Dimensions: 165/6.5L x 220/8.7H x 178/7W mm/in
Type: 7" In-Line
For continous duty
7A fuse
*Certification: CE marked ISO 9097:1991 Marine (small craft electrical fans), ISO8846 1990 (ignition protection), ISO 10133 2000 (electrical systems), EN55014-1 2006 (2004/108EC)
|
197.16 |
|
|
Air Blower 1000 Inline 165 - 24V
7″ in-line mounted marine ventilation 24V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 165mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance.
Features:
Weight: 1.2 kg/2 lbs
Dimensions: 165/6.5L x 220/8.7H x 178/7W mm/in
Type: 7" In-Line
For continous duty
3,5A fuse
Certification: CE marked ISO 9097:1991 Marine (small craft electrical fans), ISO8846 1990 (ignition protection), ISO 10133 2000 (electrical systems), EN55014-1 2006 (2004/108EC)
|
200.69 |
|
|
Air Blower 1000 Inline 250 - 24V
7″ in-line mounted marine ventilation 24V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 250mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance.
Features:
Weight: 1.4 kg/3 lbs
Dimensions: 250/9.8L x 220/8.7H x 178/7W mm/in
Type: 7" In-Line
For continous duty. 3,5A fuse
Interchangeable with Vetus Vent17824A.
*Certification: CE marked ISO 9097:1991 Marine (small craft electrical fans), ISO8846 1990 (ignition protection), ISO 10133 2000 (electrical systems), EN55014-1 2006 (2004/108EC)
|
200.69 |
|
|
Air Blower 1000 In-Line 250 - 12V
7″ in-line mounted marine ventilation 12V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 250mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance.
Features:
Weight: 1.4 kg/3 lbs
Dimensions: 250/9.8L x 220/8.7H x 178/7W mm/in
Type: 7" In-Line
For continous duty
7A fuse
Interchangeable with Vetus Vent17812A.
*Certification: CE marked ISO 9097:1991 Marine (small craft electrical fans), ISO8846 1990 (ignition protection), ISO 10133 2000 (electrical systems), EN55014-1 2006 (2004/108EC)
|
197.16 |
|
|
iL200 Plus In-Line & Submersible Pump 12V
Centrifugal submersible and inline pump;
Suitable for diesel, fresh and salt water
Quick diesel transfer with no spillage
Bait tank aeration, diesel transfer, water transfer
Water Systems to 80°C
Continuous rating but should not be run dry for long periods
Specifications
Output: up to 12.7 litres/minute at up to .75bar (2.8 gallons/minute at 11psi)
Connections: 1/2" (12.7mm) Hose
Dimensions (L x H): 142 x 38 (mm)
Amp Draw: 2.5 (amp)
Weight: 260 (g)
WARNING: This product can expose you to chemicals including FORMALDEHYDE (GAS) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
41.99 |
|
|
IL200 Plus In-Line Submersible Pump - 24V - 2.8GPM
Centrifugal submersible and inline pump.
Features:
Cable Length: 1(m)
Connections: 1/2" (12.7mm) Hose
Dimensions: 142mm long, 38mm diameter
Maximum Current: 1.5(amps)
Output: up to 12.7 litres/minute at up to .75bar (2.8 gallons/minute at 11psi)
Suitable for diesel, fresh and salt water
Quick diesel transfer with no spillage
Bait tank aeration, diesel transfer, water transfer.
Water Systems to 80 ºC
Intermittent light duty
Motor life approx 250 hours
Actual Weight: 0.33 Kg (Approx. 0.53 Kg packed)
|
47.48 |
|