|
|
11.34 |
|
|
MP Pumps 21366 PUMP FM10 C/I 184TC MT
Flomax 10 Pumpaks are liquid-ends less power source. Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Cast iron construction and will fit 184C/145TC NEMA motors with feet. PumPaks are provided less motors and with 5" maximum impeller diameters.
Specifications
Rated Capacity 140 GPM Maximum Head: 92 feet (40 PSI) Suction & Discharge Connections: 2" X 2" FNPT Impeller Diameter: Shipped with 5" maximum diameter impellers for trimming to pumping condition by customer. Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft to fit either 5/8" or 7/8" driver shaft; viton mechanical seal.
Pump water end only less motors.
Motors Required: 1-1/2 HP, 2 HP or 3 HP TEFC, 3450 rpm, single phase or three phase, 60 Hz Motor Frames Required: 184C/145TC NEMA motors with feet.
|
1631.70 |
|
|
MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump
MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount
FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.
A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.
The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
Model: Flomax 15
Part #: MP21381
Size: 3 in. NPT
Flow-Rate: 320 GPM
Head Feet: 145
Features
Material of Construction: Cast Iron
Renewable wear plate
Stainless steel drive sleeve
Stainless steel fasteners
Up to a 25' suction lift
Applications
Agricultural
Industrial
Marine
OEM
|
1762.20 |
|
|
MP Pumps 21383 FM 15 BRONZE PUMP
MP Pumps 21383, FLOMAX 15 Self Priming Centrifugal Pump, Wet End Only
FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators and Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
3" X 3" NPT Ports
Capacity up to 320 GPM
Total Head up to 145 feet
Bronze construction
5.75 inch diameter impeller
|
6386.81 |
|
|
FLOMAX®8 by MP Pump part 26079
2" x 2" Self Priming Centrifugal Pump
FLOMAX® 8 self-priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump’s built in flapper valve will maintain a full column of liquid in the suction line.
A FLOMAX® 8 PumPAK® is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive.
Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wearplate, and a semi-open dynamically balanced impeller.
The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
|
821.70 |
|
|
MP Pumps 21372 Flomax 15 Self Priming Centrifugal Pump for Water & Fertilizer
FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.
A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.
The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
Model: Flomax 15 Part# 21372
Configuration: Pumpak
PORTS: 3 in.
Flow-Rate: 320 GPM
Head Feet: 145
Features
Material of Construction: Cast Iron
Renewable wear plate
Stainless steel drive sleeve
Stainless steel fasteners Up to a 25' suction lift
Applications
Agricultural
Industrial
Marine
|
1499.40 |
|
|
MP Pumps 21312, FLOMAX 5 Self Priming Centrifugal Pump
1-1/2" X 1-1/2" NPT Ports, Capacity up to 145 GPM, Total Head up to 100 feet.
FM5PMP C: PED 5.0
MP Pumps Flomax 5, 1-1/2" pedestal mount self priming cast iron pump # 21312. MP Pumps Flomax 5, rated at 100 GPM in cast iron construction with viton mechanical seal.
Specifications
Rated Capacity 100 GPM Maximum Discharge Pressure: 40 PSI Suction & Discharge Connections: 1-1/2" X 1-1/2" FNPT Construction: Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve, 304 stainless steel stub shaft to fit 5/8"; viton mechanical seal.
Features:
Material of Construction: Cast Iron
Renewable wear plate
Stainless steel drive sleeve
Stainless steel fasteners
Up to a 25' suction lift
5 blade impeller available for higher flows
Base plate shown above is optional
Double seal available for dry run applications
Hydraulic motor .22 cu. in.
Hydraulic motor .37 cu. in.
Hydraulic motor .45 cu. in.
Stainless steel impeller
|
1003.50 |
|
|
MP Pumps 21338 PUMP FM8 BRZ PED MNT
MP Pumps Flomax 8, 2" NPT self priming centrifugal pumps # 21338. Up to 140 GPM, up to 40 PSI (92'), 3450 RPM, all bronze construction. Removable flanges and replaceable wear plates protect the housing and eliminate wear. All fasteners are Stainless Steel. Standard mechanical seal have Viton elastomers.
Specifications
Rated Capacity 140 GPM Maximum Discharge Head
92 feet (40 PSI) Suction & Discharge Connections
2" X 2" FNPT
Construction:
Cast iron housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss
weight 49 lbs.
304 stainless steel stub shaft
viton mechanical seal.
|
2989.43 |
|
|
MP Pumps 21339 Flomax 8 Self Priming Centrifugal Pump
FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.
A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.
The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
Model: Flomax 8
Part # MP 21339
Configuration: Pedestal Mount
Port Size: 2 in. NPT
Flow-Rate: 150 GPM
Head Feet: 100
Features
Material of Construction: Cast Iron
Renewable wear plate
Stainless steel drive sleeve
Stainless steel fasteners
Up to a 25' suction lift
Applications
Agricultural
Industrial
Marine
|
1033.20 |
|
|
MP Pumps 36067 PUMP HHLF HR 2" GAS/DIESEL
MP Pumps 36067, HHLF High Head Low Flow Self Priming Centrifugal Pump End Only, 1-1/2" or 2" x 1-1/2" or 2"
High Pressure USCG Secifications Auxilary Fire Control HHLF2.0PPK B: ENG 1.0 6.7 HR
|
5163.79 |
|
|
MP Pumps Flomax 5 Self Priming Centrifugal Pump
FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.
A FLOMAX PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.
The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
Model: Flomax 5 Part # MP 21302
Port Size: 1 1/2 in. NPT
Flow-Rate: 145 GPM
Head Feet: 100
Features
Material of Construction: Cast Iron
Renewable wear plate
Stainless steel drive sleeve
Stainless steel fasteners
Up to a 25' suction lift
Applications
Agricultural
Industrial
Marine
OEM
|
801.00 |
|
|
MP Pumps 21327 Flomax 8 Self Priming Centrifugal Pump
FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.
A FLOMAX PumPAK® is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.
The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.
Model: Flomax 8 part # MP 21327
Port Size: 2 in NPT
Flow-Rate: 150 GPM
Head Feet: 100
Features
Material of Construction: Cast Iron
Renewable wear plate
Stainless steel drive sleeve
Stainless steel fasteners
Up to a 25' suction lift
Applications
Agricultural
Industrial
Marine
|
840.60 |
|
|
MP Pump 23241 Pump Series 110 Ci Gas Eng
MP Pumps 23241 Series 110 End Suction Centrifugal Pump Cast
The SERIES 110 high volume centrifugal pumps are close-coupled to standard NEMA "C" face motors. Open adaptor protects motor. All models are available in cast iron, bronze or aluminum construction to suit a wide variety of liquids. All fasteners are stainless steel to reduce corrosion. Impellers are balanced to improve efficiency and bearing life. Standard carbon / ceramic / Viton mechanical seal is self-adjusting and corrosion resistant to handle almost any liquid.
|
814.50 |
|
|
MP Pump 24550 Pump Fm8 Brz Man Clutch
MP Pumps 24550 FLOMAX8 2" x 2" Self-Priming Centrifugal Pump, Bronze, Pedestal/Clutch, 5" Impeller
Renewable wear plate.
Stainless steel drive sleeve.
Stainless steel closure.
Up to a 25 foot suction lift
Specifications for this product
maximum flow150 gallons_per_minute
Included ComponentsCentrifugal Pump
UNSPSC Code40151500
MaterialBronze
body materialBronze
brand nameMP Pumps
Number of articles1
Model number24550
part number24550
|
4019.25 |
|
|
MP Pumps 36089 HHLF 2" x 2" High Head Low Flow Self Priming Centrifugal Pump, Bronze, Pumped, Closed Couple Motor, 1.12, 6.5" Impeller, High Rise Suction
HHLF (High Head Low Flow) "HR" high pressure self-priming centrifugal pumps meet USCG specifications for auxiliary fire control (46 CFR compliant) and is ABS type approved. The high suction centerline and impeller design eliminates premature priming loss while ensuring consistent priming capability. The HHLF pump is capable of achieving up to 25 feet suction lift. The HHLF series is available close coupled to NEMA "C" Face electric motors or as PumPAKs. The engine drive models are capable of close coupling to both gasoline and diesel engines with 1" keyed drive shafts. Pedestal mounted pumps are also available. The volute and impeller are removable and easily replaced.
46 CFR Complaint
ABS Type Approved
Drive Sleeve 304 stainless steel
Adaptor Cast iron Class 30 or silicon bronze CA 875
|
4824.83 |
|