|
MX8000CR
Adjustable Angle holders MX8000CR (1-5/8" ID) are our strongest and most versatile holders. The three-point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18".
Recommended poles for MX8000CR
MX8719CR - 19 ft MX Step- Tube Style
MX8716CX - 16 ft MX Step- Tube Style - Single Spreader
MX8719CX - 19 ft MX Step- Tube Style - Single Spreader
MX8720CX - 20 ft MX Step- Tube Style - Double Spreader
MX8722CX - 22 ft MX Step- Tube Style - Single Spreader or Double Spreader
|
516.32 |
|
|
AL7001CR
The AL7001CR (1-3/8"ID) is the solution for boats with a tower or when a lower angle is desired. It has a slightly larger footprint (4"x 7"). Ruggedly constructed from marine grade anodized aluminum. It can be easily attached above or below the standing platform or any flat surface. It comes in a standard angle of 22 degrees that gives it a low rise. Anodized in Bright Silver it is as strong as it is attractive. It accepts all the same poles as the AL7000 series holders.
|
220.15 |
|
|
Outrigger Holder Reducer - 1-5/8" to 1-1/2" - Pair
Downsize your outrigger holders
Reduce from 1-5/8" to 1-1/2"
|
58.68 |
|
|
MX7000CR
Adjustable Angle holders MX7000CR (1-1/2" ID) are our strongest and most versatile holders. The three point mounting distributes the stress and provides side support. This heavy duty unit allows you to set your outrigger angle for maximum efficiency. The angle is set by positioning the clamp on the main tube during installation. The main tube of this unit is designed to accept the outrigger in either end so the holder can be mounted above or below any flat surface. A fast pin can be substituted for the bolt connecting the clamp to the wing for bridge laydown capability. Approximate area required for mounting is 14-1/2" x 18".
Recomended poles for MX7000CR
AO8716CR - 16 ft Center Rigger (Mk II)
AO8718CR - 18 ft Center Rigger (Mk II)
MX8712CR - 12 ft MX Step- Tube Style
MX8715CR - 15 ft MX Step- Tube Style
MX8718CR - 18 ft MX Step- Tube Style
MX8716CX - 16 ft MX Step- Tube Style - Single Spreader
MX8720CX - 20 ft MX Step- Tube Style - Double Spreader
|
502.62 |
|
|
Stainless Steel Clamp-On Rod Holder
Stainless Steel
Type 316
Polished
Features and Benefits
Adjustable clamp to fit multiple pipe and tube sizes
For use on vertical and horizontal pipe/tube
Rotate and lock in fishing angle
Rotates and locks every 18°
Form-fitted PVC White Liner
Specifications:
Clamp Fits (Outside Diameter):1-1/16" & 1-5/16" O.D. (Pipe), 1-1/4" O.D. (Tube)
Location:T-Top Ring, Leaning Posts, Poling Platforms
Rod Holder Inside Diameter: 1-5/8"
|
129.44 |
|
|
Description - C.P. Brass Raw Water Washdown
Base diameter- 1-5/8"
Depth - 3-3/16"
Threads - 1/2" FIPT x 3/4"
Fastener - #6 (2)
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
27.24 |
|
|
The Original Wishbone Outrigger Holder
The Original Wishbone Style Outrigger Holder has been in production for over 45 years. Setting the standard for the industry, our "Junior" outrigger holder has often been imitated, but never equaled. Its ease of operation, adjustable fishing angle, ability to lay down for bridges and small footprint makes it the ideal holder for a multitude of boats.
Durability was the watchword at its conception. You won't find plastic parts in this holder. Constructed of heavy duty brass forgings, heavy wall brass pipe and a stainless steel main tube, it epitomizes strength and reliability. The three point mounting system provides maximum strength and distributes the stress to the mounting surface over a wide area. This holder can be mounted vertically or angled toward the stern. Somewhere between twenty to thirty five degrees is normal.
Model OH226S is for use with our deluxe 19ft. single spreader poles and non-spreader poles up to 22ft.
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
1859.68 |
|
|
AL7211CR
The AL7211CR (1-3/8"ID) is the perfect holder for boats in the 16 to 31 ft range. Its economical price and small footprint (3"x 5") make it our most popular center rigger holder. The receiving tube of this marine grade anodized holder is set at a 45 degree angle. This is the perfect angle for boats where the mounting position is low and the cockpit is not extremely deep (e.g. mounting on T-Tops, Hard Tops, or Fly-Bridges). Compatible poles are 12 or 14ft in length and come standard in bright silver anodized finish with a Black Spike.
Recomended poles for AL7211CR
AO8712CR - 12 ft Center Rigger (Mk II)
AO8714CR - 14 ft Center Rigger (Mk II)
MX8712CR - 12 ft MX Step- Tube Style
|
108.00 |
|
|
MX Pro Series Fixed Angle Center Rigger Holder - 22° - 1.5" ID - Bright Silver
The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by.
MX Pro Series (1-1/2"ID) is the solution for boats with a tower or when a lower angle is desired
Slightly larger footprint (5"x 7")
Ruggedly constructed from marine grade anodized aluminum
Can be easily attached above or below the standing platform or any flat surface
Anodized in Bright Silver it is as strong as it is attractive
|
261.70 |
|
|
MX Pro Series Fixed Angle Center Rigger Holder - 30° - 1.5" ID - Bright Silver
The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by.
MX Pro Series (1-1/2"ID) is the solution for boats with a tower or when a lower angle is desired
Slightly larger footprint (5"x 7")
Ruggedly constructed from marine grade anodized aluminum
Can be easily attached above or below the standing platform or any flat surface
Anodized in Bright Silver it is as strong as it is attractive
|
261.70 |
|
|
MX Pro Series Fixed Angle Center Rigger Holder - 45° - 1.5" ID - Bright Silver
The Center Rigger has proven to be an effective tool when trolling. It should be the highest outrigger when the others are deployed in the fishing position. Its line runs straight down the middle with its bait being the farthest back. The Center Rigger bait, more often than not, is the one struck after the other baits have streamed by.
MX Pro Series (1-1/2"ID) is the solution for boats with a tower or when a lower angle is desired
Slightly larger footprint (5"x 7")
Ruggedly constructed from marine grade anodized aluminum
Can be easily attached above or below the standing platform or any flat surface
Anodized in Bright Silver it is as strong as it is attractive
|
261.70 |
|
|
AL7301CR
Fits 1.050" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|
|
AL7302CR
Fits 1.315" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|
|
AL7303CR
Fits 1.660" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|
|
AL7304CR
Fits 1.900" Pipe
The AL7300 (1-3/8"ID) series of Clamp-On Center Rigger Holders are available to fit standard size Schedule 40 Aluminum Pipe. Easy installation and unobtrusive design make this a popular installation where a horizontal pipe is available. This holder can also be used for other applications.
|
103.85 |
|