Heavy Duty Flangemount Blower Heavy Duty Blowers are designed for applications such as commerical or high use engine room ventilation and extraction where a long life requirement demands heavy duty motors with long brush life. Built to provide the same high outputs as our standard specification blowers. 5,000 hr motor life for the heaviest of applications Continuous duty Efficient high volume air flow Outlet flange mounts directly on bulkhead Slip on inlet ducting connection Low current draw Corrosion resistant materials throughout Dimensionally stable quiet running Delrin rotors Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection) ISO 9097 MARINE (Electric Fans) WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Heavy Duty Flexmount Blower DC 250 CFM Flexmount Continuous Duty 4" Blower Extended Life 5,000 Hour Motor Tough Reinforced Thermoset Plastic Housing Mounts to Any Flat Surface Slip-On Inlet Ducting Connection Efficient High Volume Air Flow Low-Current Draw Corrosion-Resistant Materials Throughout N.M.M.A Type Accepted Meets USCG Electrical Regulations to Title 33 Chapter I, Part 183 Subpart I and ISO 8846 for Ignition Protection Complies with ISO 9097 Marine CE Conforms with EN 5008-1 for Supression of Electro-magnetic interference WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

4" Flangemount Heavy Duty Blower - 24V - 250 CFM The powerful flange mount blower is designed for use wherever continuous ventilation is required. A motor life of 5,000 hours is guaranteed for service in the most challenging conditions. Features: Extended life 5,000-hour motor They provide outputs of 250 cfm (7.1m3/min) 24V DC Rigid reinforced thermoset plastic housing Mounts to any flat surface Slip-on inlet ducting connection Efficient high-volume airflow Low-current draw Corrosion-resistant materials throughout N.M.M.A. type accepted Meets USCG Electrical Regulations of Title 33 *Sold as an Individual

Flangemount Blower DC 250 CFM Flangemount 4" Blower Tough Reinforced Plastic Housing Mounts to any flat surface Slip-on Inlet Ducting Connection Efficient High Volume Air Flow Low-Current Draw Corrosion-Resistant Materials Throughout N.M.M.A Type Accepted Meets USCG Regulations 183.410 and ISO 8846 MARINE for ignition protection Complies with ISO 9097 MARINE VARIATIONS WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Heavy Duty Flexmount Blower DC 250 CFM Flexmount 4" Blower Tough Reinforced Plastic Housing Universal Flexmount Bracket permits outlet to face any direction Slip-On Inlet Ducting Connection Efficient High Volume Air Flow Low-Current Draw Corrosion-Resistant Materials Throughout N.M.M.A Type Accepted Meets USCG Regulations 183.410 and ISO 8846 MARINE for ignition protection Complies with ISO 9097 MARINE VARIATIONS WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Heavy Duty Flexmount Blower AC 250 CFM Flexmount Continuous Duty 4" Blower Flexmount Blowers are built to the same high specification as the Heavy Duty Flangemount Blowers for use as air intake or extraction systems in engine rooms, fuel compartments, galleys or heads. Extended Life Induction Motor Tough Reinforced Thermoset Plastic Housing Continuous duty motor with thermal overload protection Flexmount universal bracket permits outlet to face any direction Slip-On Inlet Ducting Connection Efficient High Volume Air Flow Low-Current Draw Corrosion-Resistant Materials Throughout 5,000 hr motor life for teh heaviest of applications. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

DC 250 CFM Flangemount 4" Blowers Features: Tough Reinforced Plastic Housing Mount to any Flat surface Slip-On Inlet Ducting Connection Efficient High Volume Air Flow Low Current Draw Corrosion-Resistant Materials Throughout N.M.M.A. Type Accepted Meets USCG Regulation 183.410 and ISO 8846 MARINE for Ignition Protection Complies with Complies with ISO 9097 MARINE WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

DC 250 CFM Flexmount Continuous Duty 4" Blowers Features: Extended Life 5,000 Hour Motor Tough Reinforced Thermoset Plastic Housing Mounts To Any Flat Surface Slip-On Inlet Ducting Connection Efficient High Volume Air Flow Low-Current Draw Corrosion-Resistant Materials Throughout N.M.M.A. Type Accepted Meets USCG Electrical Regulations of Title 33 Chapter I, Part 183 Subpart I and IS0 8846 for Ignition Protection Complies with ISO 9097 Marine CE Conforms with EN 5008-1 for Supression of Electro-magnetic interference WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

ATLAS™ 12" Set Back Hydraulic Jack Plate - Heavy Duty T-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp.  5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ATLAS™ 14" Set Back  Hydraulic Jack Plate - Heavy Duty T-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade. T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp.  5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ATLAS™ 6" Set Back Hydraulic Jack Plate - Heavy Duty T-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the new ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp.  5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ATLAS™ 8" Set Back Hydraulic Jack Plate - Heavy Duty T-H Marine’s ATLAS™ Hydraulic Jack Plate is now available in a “HEAVY DUTY” upgrade.T-H Marine’s ATLAS™ Hydraulic Jack Plate is the #1 selling jack plate in the world and the #1 Choice by fishing professionals and boat manufacturers. With the new ATLAS™ HEAVY DUTY, the product is available for applications on even larger outboards, rated for engines up to 400 hp.  5 REASONS YOU SHOULD CHOOSE THE ATLAS™ HYDRAULIC JACK PLATE ATLAS™ is truly the best hydraulic jack plate in the world ATLAS™ is factory installed by more boat manufacturers than any other plate ATLAS™ is used by more professional fisherman than any other hydraulic jack plate ATLAS™ is the #1 selling hydraulic plate in the world – sold & serviced by more outlets ATLAS™ hydraulic actuator is made in the U.S.A. vs. our competitors being from China 6 WAYS THE ATLAS™ CHANGED HYDRAULIC JACK PLATES FOREVER ATLAS™ is made by T-H Marine/CMC, who were the FIRST to offer an actuator inside the jack plate – the competition copied ATLAS™ was the first plate to offer predrilling for shallow water anchors – the competition copied ATLAS™ was the first and only plate that did not require regular grease lubrication – the competition design cannot do that ATLAS™ was the first plate to include a heavy duty safety cable to protect boaters from engine entering cockpit upon failure ATLAS™ was the first plate to offer a very simple actuator replacement in the field ATLAS™ was the first major development in hydraulic jack plates in over a decade – spurring hydraulic jack plate improvement WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

HotShot HD6 Heavy Duty Washdown Pump with 25' HoseCoil - 12V - 6 GPM - 70 PSI Years of clean decks and satisfaction in the form of robust and reliable high-flow and high-pressure diaphragm pumps. The Jabsco legacy of exceptional products continues with this updated and improved lineup of washdown pumps and kits.  HD (Heavy Duty) models include a wider diameter motor with a powder coated shell, cast aluminum endbells and lower housing to improve pressure capability and life.  Standard models provide exceptional performance in an economical footprint. A plastic housing protects the motors from corrosion.  Features: Co-molded diaphragm technology for long life and durability HD models feature heavy duty, motors and cast aluminum lower housings which allow for long-life, even at high pressures Efficient and quiet operation Integrated, sealed pressure switch for on-demand operation Self-priming allows for installation versatility Can run dry without damage Quick connect ports for ease of installation, servicing, and maintenance Vibration dampening mounting feet Full kit versions available which include 25' (7.6m) hose coil Specifications: Motor design: Brushed, permanent magnet TENV  Pumphead upper housing material: Glass fiber reinforced polypropylene  Diaphragm: Co-molded TPV  Check valves: EPDM  Max inlet pressure: 30 PSI (2.1 Bar)  Fluid temperature range: 32°F – 140°F (0°C – 60°C)  Dry self-priming capability: 7ft min (2.1m min)  Certifications: CE, ISO8846, RCM  Ingress protection: IPX6 Fittings & Accessories: Quick Connect straight hosebarb and GHT fittings. Size varies by model.  90° 20 mesh Quick Connect strainer  Trigger nozzle & Quick Connect hose adapters  Kit version includes 25' deluxe HoseCoil WARNING: This product can expose you to chemicals including ANTIMONY OXIDE (ANTIMONY TRIOXIDE) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Sherwood G-2903X-J Engine Cooling Pump JPR-C1100 Replaces Cummins 3349392, 5260393, 4929178, Sherwood G2903X, G2903-01, G2903-02.  Engine Model QSM11   Uses JMP Impeller p/n: 8359-01K Port Type: Flange 2" Replaces Genuine Cummins Pump p/n(s): 3349392, 4929178, 5260393 Replaces Sherwood Pump p/n(s): G2903X, G2903-01, G2903-02 For Engine Model(s): QSM11 Pump Weight (approx): 35.0 LBS (15.91 KG)   Parts Internally Compatible to Genuine: YES   100% Plug & Play Replacement Heavy Duty Marine Grade Casting Marine Grade Shaft (3X Series Non-Magnetic) O-Ring End Cover Packing Heavy Duty Material for Cam Liner vs Sherwood's Plastic Cam High Performance Impeller High Volume Flow Capacity Fast Flow Capacity

Heavy Duty Toggle Switch SPST On-Off 2 Screw Standard or long handle. Universal application. Silver contacts. Mounting stem is nickel-plated brass 15/32" -32 thread, 15/32" (11.9mm) long, and fits panels up to 9/32" (7.1mm) except where stated otherwise. phenolic housing, with plated steel cap. Nickel-plated brass mounting hardware. Blade terminals: .250 quick connect. Screw terminals: 6-32 screws. 25A at 12V, 15A at 24V, and 10A at 36V DC.