Portable Self-Priming RV Macerator Waste Pump Kit - 12V The Flojet 18555-000 DC portable waste pump is the ideal solution for emptying holding tanks on recreational vehicles and avoiding dump stations. The macerator section grinds waste down to a particle size of 1/8" maximum so it can easily be pumped through a garden hose (5/8" minimum). The pump section is self-priming, permitting the unit to be mounted above the tank in a convenient location. Empties most recirculating toilets in less than 2 minutes; empties a typical 30-gallon holding tank in less than 3 minutes. The 18555-series waste pump will macerate and pump all waste and tissue normally found in recreational vehicle waste systems. *IT WILL NOT HANDLE HARD SOLID OBJECTS, SANITARY NAPKINS, OR RAGS Features: Connects directly to the RV waste outlet Eliminates 3" (75mm) sewer hose Garden hose discharge port Freshwater rinse capabilities Remote handheld on/off switch with 6' (1.8M) wire harness Ability to dump longer distances Ability to drain holding tanks at home Easy cleanup and storage Rugged portable storage case USCG and CSA listed Run dry protection WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Flojet 03811-143A Mpu 12V S/E 3C Sw150Bp Flojet 03811133A Self-Priming High Pressure Triplex Pump - 150 PSI, 1.4 GPM, 12 VDC Electric Pump   Flojet's 03811133A pump features a unique three-chamber design that delivers an flow rate of 1.4 GPM. Handles pressures up to a maximum of 150 PSI. Well-suited for spraying, misting, filtration, cooling, dispensing, and pressure boosting. NPTF Threaded inlet and outlet ports with a diameter that measures 3/8 inches. Specifications: Open Flow: GPM 1.4  Switch Pressure: PSI 150 Check Valve: Viton¨  Diaphragm: Santoprene¨  Voltage: 12 VDC  Duty Cycle: Intermittent  Port Size: 3/8" NPTF Motor Design Perm. Magnet TENV (non-ventilated) Pump Head Material: Glass Filled Nylon Certifications: CE, NSF components Features: Flow rates up to 1.4 GPM (5.3 LPM) and operating pressure of up to 150 psi (10.3 bar) Constructed from a selection of materials suitable for handling a broad range of chemicals Innovative bypass design Self-priming up to 8ft (2.4m) Sealed motor Can run dry for extended periods of time without damage Coinjected molded diaphragm technology Consistent pressure over time  

Flojet 03811-133A Mpu 12V S/V 3C Sw150 Bp Flojet 03811133A Self-Priming High Pressure Triplex Pump - 150 PSI, 1.4 GPM, 12 VDC Electric Pump   Flojet's 03811133A pump features a unique three-chamber design that delivers an flow rate of 1.4 GPM. Handles pressures up to a maximum of 150 PSI. Well-suited for spraying, misting, filtration, cooling, dispensing, and pressure boosting. NPTF Threaded inlet and outlet ports with a diameter that measures 3/8 inches. Specifications: Open Flow: GPM 1.4  Switch Pressure: PSI 150 Check Valve: Viton¨  Diaphragm: Santoprene¨  Voltage: 12 VDC  Duty Cycle: Intermittent  Port Size: 3/8" NPTF Motor Design Perm. Magnet TENV (non-ventilated) Pump Head Material: Glass Filled Nylon Certifications: CE, NSF components Features: Flow rates up to 1.4 GPM (5.3 LPM) and operating pressure of up to 150 psi (10.3 bar) Constructed from a selection of materials suitable for handling a broad range of chemicals Innovative bypass design Self-priming up to 8ft (2.4m) Sealed motor Can run dry for extended periods of time without damage Coinjected molded diaphragm technology Consistent pressure over time

Flojet D3631B5011A Pump 115V 60Psi 2.1Gpm Flojet D3631B5011A Self-Priming Duplex Diaphragm Bypass Pump - 60 PSI, 1.6 GPM, 115 VAC Electric Pump   The Flojet D3631B5011A is a double diaphragm pump includes an integrated 115 VAC electric motor. Engineered with an internal bypass system and is self-priming. Pump body is made from polypropylene for chemical resistance. Features the ability to run dry without damaging the critical components of the pump. Specifications: Voltage: 115 VAC GPM: 1.6 GPM Max Pressure: 60 PSI  Ports: 3/8" FNPT Material: Polypropylene Diaphragm: Buna Check Valve: Buna Motor: Electric

Flojet D3231B5011A Mpu 24V 100Gph 3/8 Ports Flojet D3231B5011A Self-Priming Duplex Diaphragm Bypass Pump - 60 PSI Bypass, 1.6 GPM, 24 VDC Polypropylene Pump    The Flojet D3231B5011A is a double diaphragm pump includes an integrated 24 VDC electric motor. Engineered for the ability to be self-priming up to 8 feet. Pump body is made from polypropylene for corrosion and chemical resistance. Features the ability to run dry without damaging the critical components of the pump and features a built-in back flow preventer. Specifications: Voltage: 24 VDC GPM: 1.6 GPM Bypass: 60 PSI Max Pressure: 100 PSI  Ports: 3/8" NPT Female Material: Polypropylene Diaphragm: Buna Check Valve: Buna Motor: Electric

Flojet 03811-043A Mpu 115V S/E 3C Sw150 Bp Flojet 03811043A Self-Priming High Pressure Triplex Pump - 150 PSI, 1.4 GPM, 115 VAC Electric Pump   The Flojet 03811043A pump features a unique three chamber design that delivers excellent flow rates and pressures. Handles pressures up to a maximum of 150 PSI. Well-suited for spraying, misting, filtration, cooling, dispensing and pressure boosting. NPTF Threaded inlet and outlet ports with a diameter that measures 3/8 inches. Specifications: Open Flow: GPM 1.4  Switch Pressure: PSI 150 Voltage: 115 VAC  Duty Cycle: Intermittent  Port Size: 3/8" NPTF Motor Design Perm. Magnet TENV (non-ventilated) Pump Head Material: Glass Filled Nylon Diaphragm: Santoprene¨  Check Valve: EPDM¨  Certifications: CE, NSF components Features: Flow rates up to 1.4 GPM (5.3 LPM) and operating pressure of up to 150 Psi (10.3 bar) Constructed from a selection of materials suitable for handling a broad range of chemicals Innovative bypass design Self-priming up to 8ft (2.4m) Sealed motor Can run dry for extended periods of time without damage Coinjected molded diaphragm technology Consistent pressure over time

Flojet 03811-033A 115V S/V 3C Sw150 Flojet 03811033A Self-Priming High Pressure Triplex Pump - 150 PSI, 1.4 GPM, 115 VAC Electric Pump   The Flojet 03811033A features a unique three chamber design that delivers excellent flow rates and pressures. Handles pressures up to a maximum of 150 PSI. Well-suited for spraying, misting, filtration, cooling, dispensing and pressure boosting. NPTF Threaded inlet and outlet ports with a diameter that measures 3/8 inches. Specifications: Open Flow: GPM 1.4  Switch Pressure: PSI 150 Check Valve: Viton¨  Diaphragm: Santoprene¨  Voltage: 115V AC  Duty Cycle: Intermittent  Port Size: 3/8" NPTF Motor Design Perm. Magnet TENV (Non-Ventilated) Amp Draw: 1.2 Amps Max for 115V AC Pump Head Material: Glass Filled Nylon Certifications: CE, NSF components   Features: Flow rates up to 1.4 GPM (5.3 LPM) and operating pressure of up to 150 psi (10.3 bar) Constructed from a selection of materials suitable for handling a broad range of chemicals Innovative bypass design Self-priming up to 8ft (2.4m) Sealed motor Can run dry for extended periods of time without damage Coinjected molded diaphragm technology Consistent pressure over time

Flojet D36X001A 115V .7Gpm V/S Sw45 Bp R Flojet D36X001A Self-Priming Duplex Diaphragm Bypass Pump - 45 PSI, .7 GPM, 115 VAC Electric Pump   The Flojet D36X001A is a double diaphragm pump includes an integrated 115 VAC electric motor. Engineered with a built-in backflow preventer and an internal bypass standard. Pump head is made from polypropylene for chemical resistance. Features the ability to run dry without damaging the critical components of the pump. Specifications: Voltage: 115 VAC GPM: .7 GPM Max Pressure: 45 PSI  Material: Polypropylene Motor: Electric

Run-Dry Macerator Waste Pump WASTE EVACUATION The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage. FISH BOX AND LIVEWELL TANK EVACUATION The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties. Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats. Triple sealed motor to prevent both internal and external motor corrosion New Four-bladed chopper reduces clogging Detects the absence of fluid then shuts-off pump before impeller is damaged Sensor provides adequate run-dry period to allow initial priming of the pump Interrupting power supply to the macerator resets the Run-Dry Device Flow rate to 12 gpm Self-priming to 4ft Fitting: Inlet Port: 1-1/2" Hose Barb plus 1-1/2 NPT Discharge Port: 1" Hose Barb WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Self-Priming Dual Blade Macerator Pump - 24VDC, 13GPM Designed specifically for sanitation waste and fish box evacuations, SHURFLO®'s Macerator pump features a premium impeller design with run-dry capability and includes our seamless shell motor with o-ring sealed end bells and a sealed manual turn key. SHURFLO®'s unique dual blade and housing construction ensures problem free pumping, providing superior performance in harsh marine environments. Thermally protected and ignition protected. 1 Year Warranty Specifications: 24 VDC, 13 GPM [49 LPM] 9 Amps (Max.) 1-1/2" [38.1mm] Inlet Barb 1-1/2" [38.1mm] NPT Outlet Port 1" [25.4mm] Barb Dimensions: 10.6" [269mm] x 4.9" [125mm] x 3.8" [97mm]

Electric Conversions Features: Directly replaces manual pump assembly Easy to Install Simple to operate Dual action control allows water level to be varied Fits all Jabsco and Par 29090 and 29120 standard and large bowl toilets. Adaptors available to fit many other makes Suitable for use in above or below waterline installations Built in macerator Meets EN50081-2 for Electro Magnetic Compatibility (EMC) Meets ISO 8846 MARINE and USCG 183.410 for Ignition protection Self priming up to 0.6m(2ft) Waste pump discharges over an anti siphon loop up to 1.8m(6ft) and out of a through hull fitting down to 0.9m(3ft) below the surface Typical power consumption is less than 1.0 amp hour(12 Volt)

Waste Water Diaphragm Pump 32L (8.5 GPM) - 12V Single chamber, self priming, heavy duty diaphragm pump 12V for waste water. Black water transfer or pump out. Capacity 32 L/min (8,5 GPM), flexible installation with 360 degree rotational ports. Quiet operation and low power consumption. Operates with no need for filter, equipped with double non-return valves. Including 38mm (1,5″) straight and 90 degree rotational connectors. 6A fuse. Interchangeable with Johnson Pump 10-13373-03. Specifications: Weight: 1 kg/1.5 lbs Dimensions: 141/5.5L x 105/4H x 140/5.5W mm/in  Type: Black Water *CE marked 94/25/ECC, ISO8846 Small Craft, Electromagnetic compatibility 89/336/EEC, EN51014 1993/radio disturbance

Flojet 04300-531A Mpu 115V S/E Pse Sw40 Flojet 04300531A Self-Priming Quad Diaphragm Pump - 35 PSI, 3.5 GPM, 115 VAC Pump and Electric Motor   Flojet's 04300531A is a quadruple diaphragm pump with a four-piston design that delivers a high flow rate reaching a maximum of 3.5 GPM. Pump self-primes up to 2.4m vertical lift. Pump body is manufactured using polypropylene for its chemical and corrosion resistant properties. Equipped with a 1/2-inch hose barb inlet and a 1/2-inch male Quest outlet. Compatible with 115 VAC electrical connections. Specifications: Voltage: 115 VAC Inlet: 1/2" Hose Barb Outlet: 1/2" Male Quest Flow: 3.5 GPM Max PSI: 35 PSI  Body: Polypropylene] Check Valve: EPDM  Diaphragm: Santoprene Option: Pressure Switch Features: Self-primes up to 2.4m vertical lift Handles Water-Like and Viscous Liquids up to 250 cP Four-piston design delivers higher flow rates Chemical-resistant polypropylene pump head for Iong life Choice of elastomeric materials to work with many chemicals Quick-connect plug-in ports for easy installation Optional pressure-switch control to run the pump only as needed  

Commercial Duty Vane Pump - 12V GROCO  Vane Pumps are self-priming. Relatively high flow (more than gear pumps) makes them suitable for general purpose duties such as deck-wash, bilge pumping (filtered inlet),  fuel transfer, ballast transfer, and oil change.  Ignition protected motor and #316 stainless steel shaft. SPO-80 Series Vane Pumps have a more powerful motor and are better suited for long run-time or head pressure greater than 20 PSI.  Specifications: Self Priming: YES Thread NPT: 1/2" + Garden Hose Adaptor Control Type: None Max GPM: 7 Breaker DC: 30 Amp

Flojet 04300-515A Mpu 115V 3.3Gpm S/V Sw45 Pc Flojet 04300515A Self-Priming Quad Diaphragm Pump - 35 PSI, 5 GPM, 115 VAC Electric Diaphragm Pump   Flojet's 04300515A pump is a quadruple diaphragm pump that delivers a maximum flow rate of 5 GPM. Pump self-primes up to 2.4m vertical lift. Pump body is manufactured using polypropylene for chemical resistance. Utilizes quick connect plugin ports for easy installation. Specifications: Voltage: 115 VAC Ports: 3/4" Hose Barb Open Flow: 5 GPM Max PSI: 35 Body: Polypropylene