|
B.O.S. Battery Optimization System - 12V - 2-Bank
B.O.S. actively shuttles energy between batteries to keep “the pack” balanced, increasing battery strength and longevity.
Batteries in a pack will become “out of balance” and the pack is only as good as its “weakest link”. In watercraft applications, this is further compounded when the trolling motor battery is used for peripherals and/or to assist the cranking battery.
B.O.S. actively shuttles energy as needed between batteries wired in series to ensure equal voltage before, during and after charging.
B.O.S. keeps packs balanced, enabling maximum performance, and quadruples run time on the water.
Premature battery failure due to an unbalanced pack has been, unfortunately, accepted as the ‘norm’ for decades. The B.O.S. answers this call with a BSAP-24 algorithm that can accurately predict and select the battery that needs additional energy to match the other batteries within the pack. This simultaneously and successfully extends the life of each battery in the pack, as well as increasing run times.
Features:
Available in 6V, 8V, and 12V configuration
Up to six batteries in series
Battery Selection and Prediction (BSAP-24) algorithm
Less than 1mA sleep mode
Transfer rate up to 7.5A
Self-powered
Any type of battery chemistry
Used in any application where batteries are in series:
Marine
Golf
Industrial
Aerial Equipment
Solar Power
Electrical Vehicles
Communications
Defense/Military
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
343.18 |
|
|
B.O.S. Battery Optimization System - 12V - 3-Bank
B.O.S. actively shuttles energy between batteries to keep “the pack” balanced, increasing battery strength and longevity.
Batteries in a pack will become “out of balance” and the pack is only as good as its “weakest link”. In watercraft applications, this is further compounded when the trolling motor battery is used for peripherals and/or to assist the cranking battery.
B.O.S. actively shuttles energy as needed between batteries wired in series to ensure equal voltage before, during and after charging.
B.O.S. keeps packs balanced, enabling maximum performance, and quadruples run time on the water.
Premature battery failure due to an unbalanced pack has been, unfortunately, accepted as the ‘norm’ for decades. The B.O.S. answers this call with a BSAP-24 algorithm that can accurately predict and select the battery that needs additional energy to match the other batteries within the pack. This simultaneously and successfully extends the life of each battery in the pack, as well as increasing run times.
Features:
Available in 6V, 8V, and 12V configuration
Up to six batteries in series
Battery Selection and Prediction (BSAP-24) algorithm
Less than 1mA sleep mode
Transfer rate up to 7.5A
Self-powered
Any type of battery chemistry
Used in any application where batteries are in series:
Marine
Golf
Industrial
Aerial Equipment
Solar Power
Electrical Vehicles
Communications
Defense/Military
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
343.18 |
|
|
On-Board Battery Charger 8A / 12V - 2 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
107.62 |
|
|
On-Board Battery Charger 10A / 12V - 2 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
136.60 |
|
|
On-Board Battery Charger 20A / 12V - 2 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
176.12 |
|
|
Battery Optimization System (B.O.S.) - 12V - 4-Bank
The Pro Charging Systems Battery Optimization System keeps batteries balanced enabling maximum performance. The system can quadruple run time on the water for boaters and other users.
Premature battery failure due to an unbalanced pack has unfortunately been accepted as the ‘norm’ for decades. The B.O.S. breaks through those accepted “norms” and solves the problem with a BSAP-24 algorithm that can accurately predict and select the battery that needs additional energy to match the other batteries within the pack. This simultaneously and successfully extends the life of each battery in the pack. The net result is substantially increased run times and extended battery life.
The Battery Optimization System is the perfect companion device to utilize with Pro Charging Systems advanced battery chargers.
B.O.S. is compatible with PROView™ Link battery monitoring software that enables you to monitor your battery status via your smart phone or tablet. The PROView™ Link App is available to download for free at the Apple and Google Play stores. Learn more about the capabilities of PROView™ Link at the Energy Management page.
Applications: Inland Watercraft, Saltwater Watercraft, Motorhomes, Industrial, Golf Carts, Utility Carts and more.
Features:
Approved for use with Wet Cell, AGM and Lithium Ion batteries
Designed for 12V batteries
Designed for use in fresh and saltwater
Up to four batteries in series
BSAP-24 Battery Selection and Prediction Algorithm on board
Less than 1mA sleep mode
Self-powered
The Battery Optimization System is compatible with most Lithium* batteries.
*Always verify with PCS before using with Lithium batteries.
*Use PROVIew™ Link to configure B.O.S. for use with approved lithium batteries.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
366.44 |
|
|
On-Board Battery Charger 5A / 12V - 1 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
87.00 |
|
|
On-Board Battery Charger 10A / 12V - 1 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
127.20 |
|
|
On-Board Battery Charger 15A / 12V - 3 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
166.33 |
|
|
On-Board Battery Charger 30A / 12V - 3 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
321.28 |
|
|
On-Board Battery Charger 40A / 12V - 4 Bank - 120V Input
Guest On-Board battery chargers have been redesigned from the inside out with the customer in mind. Our newest generation On-Board Marine battery chargers include leading advancements in digital charging technology and waterproof design/construction. Every Guest charger has a dedicated charging, sensing and control per bank. The easy to read graphics indicates the status of each battery bank through the charging process.
Features:
All high frequency, digital charging technology
Fully automatic 5-stage performance charging
Dedicated battery charging, sensing and control per bank
Expanded LED charge status monitor
Wiring and battery fault detection
Auto-maintain energy saver mode
Up to 40 percent lighter
100 percent Waterproof (IP67) and shock resistant for all fresh and saltwater applications
All models are pre-wired for easy installation
For all 12 volt flooded and AGM lead acid batteries
Built-in safety: reverse polarity, over-current, over-voltage, over-temperature and ignition protection. In-line fuses for maximum DC wire protection.
2 year warranty
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
399.56 |
|
|
50A Battery Charger - 12V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor
This advanced fully automatic three-stage 50 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks.
Features:
Switch mode technology for high efficiency, lightweight and quiet operation
Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell
Can charge 2 banks of batteries simultaneously, no isolator necessary
Can be used as a power supply or DC UPS when used in conjunction with a battery
User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz
User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of stand-alone and loaded Lead Acid Batteries
“Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries
Voltmeter and Ammeter for monitoring
Fan cooled based on output current
Protections: Short circuit, overload, reverse battery connection and over temperature
Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively
Specifications:
Input: 120 VAC 60 Hz or 230 VAC 50 Hz
Output: 12 VDC
Amps: 50
Remote Control: 900-RC
Weight: 9.0 (lbs)
Weight: 4.1 (kg)
Dimensions: 13.03 x 9.60 x 3.82 (in)
Dimensions: 331 x 244 x 97 (mm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
445.22 |
|
|
80A Battery Charger - 12V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor
This advanced fully automatic three-stage 80 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks.
Features:
Switch mode technology for high efficiency, lightweight and quiet operation
Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell
Can charge 2 banks of batteries simultaneously, no isolator necessary
Can be used as a power supply or DC UPS when used in conjunction with a battery
User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz
User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries
“Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries
Voltmeter and Ammeter for monitoring
Fan cooled based on output current
Protections: Short circuit, overload, reverse battery connection and over temperature
Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively
Specifications:
Input: 120 VAC 60 Hz or 230 VAC 50 Hz
Output: 12 VDC
Amps: 80
Remote Control: 900-RC
Weight: 9 (lbs)
Weight: 4.1 (kg)
Dimensions: 15 x 9.61 x 3.82 (in)
Dimensions: 381 x 244 x 97 (mm)
Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B
Warranty: 2 Year Limited
Applications:
Automotive
Recreational vehicles
Marine
Communications sites
Battery back-up systems
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
632.32 |
|
|
Gianneschi ECOINOX-1-CE-12V Water System 12V
Main Water Pressure System features:
A valid substitute mechanical control
Compact size
Constant flow with variable water demand
Dry run protection
Jet type self priming el/pumps in bronze or s/steel
No accumulator tank needed
Pre-set pressure system (no adjustments need)
Reduced maintenance
Port Size: From 1'' to 1'' 1/2 BPS
|
1681.78 |
|
|
Ampco Pumps AC114MD56C-S/VITON Peo 1 1/2 X 1 1/2 Kit
|
1731.24 |
|