LANLink NMEA 2000 To Ethernet Gateway More and more boats now have a wireless router fitted or utilize services like Digital Yacht 4G Connect for internet connectivity. LANLink is an NMEA to ethernet gateway that enables the boat’s NMEA data to integrate into the router network -allowing connected devices and apps to take advantage of the data. LANLinkis available in two versions suitable for NMEA 0183 and NMEA 2000 respectively. It features an easy-to-use web interface allowing any device with a browser to configure NMEA baud rates and IP/Port information. It can support multiple TCP/IP connections and is bi-directional. Once connected to the onboard network via a simple CAT 5/6 patch cable, users can set apps like TZ iBoat, iNavX, NavLink, iSailor, Imray, Weather 4D, etc., by simply entering the IP address and port for streaming NMEA data. *This version ships with an iKonvertNMEA Certified gateway Features: NMEA 2000 to ethernet gateway version The NMEA 2000 version ships with an iKonvertNMEA Certified gateway for easy connection to the NMEA 2000 backbone (easily configurable for multiple installation options) 12/24v DC low power operation Connects to router or devices via simple RJ45 Cat 5/6 patch cable connection Web user interface for easy setup from the connected device via browser TCP/IP or UDP connection modes –support for up to 5 connected devices with TCP/IP Bi-Directional The NMEA 2000 variant can offer raw mode with encapsulated PGNs or conversion mode (for apps) supporting AIS, instruments, and GPS RS232 port for PC apps too Status indicators for power, data in-out, network link, and server status Set-Up: Easy menu-driven web UI accessible via web browser on a client device with no complicated software to install for setup Configure NMEA data for 4800 or 38400 baud and set mode (TCP/IP or UDP) and port Set up with fixed or dynamic IP address Status page for system diagnostics Specifications: Power: 10-35V DC (Consumption approx. 50mA at 12V DC) Network Port: Ethernet RJ45 10/100MB IP Mode: Static or DHCP Operating Mode *TCP/IP or UDP; Support for up to 5 connected devices in TCP/IP mode; *Recommended mode of operation NMEA Input: Configurable 4800 or 38400 baud (NMEA 0183) NMEA 2000 option via iKonvertgateway Operating temp: -25 to +70 degrees C LED Indicators: Power -Status -Link -Data In -Data Out Options: RS232 connectivity (non-concurrent with NMEA) Dimensions (W x H): 95mm x 86mm

LANLink NMEA 0183 To Ethernet Gateway More and more boats now have a wireless router fitted or utilize services like Digital Yacht 4G Connect for internet connectivity. LANLink is an NMEA to ethernet gateway that enables the boat’s NMEA data to integrate into the router network -allowing connected devices and apps to take advantage of the data. LANLinkis available in two versions suitable for NMEA 0183 and NMEA 2000 respectively. It features an easy-to-use web interface allowing any device with a browser to configure NMEA baud rates and IP/Port information. It can support multiple TCP/IP connections and is bi-directional. Once connected to the onboard network via a simple CAT 5/6 patch cable, users can set apps like TZ iBoat, iNavX, NavLink, iSailor, Imray, Weather 4D, etc., by simply entering the IP address and port for streaming NMEA data. Features: NMEA 0183 to ethernet gateway version 12/24v DC low power operation Connects to router or devices via simple RJ45 Cat 5/6 patch cable connection The web user interface for easy setup from the connected device via the browser TCP/IP or UDP connection modes –support for up to 5 connected devices with TCP/IP Bi-Directional The NMEA 2000 variant can offer raw mode with encapsulated PGNs or conversion mode (for apps) supporting AIS, instruments, and GPS RS232 port for PC apps too Status indicators for power, data in-out, network link, and server status Set-Up: Easy menu-driven web UI accessible via web browser on a client device with no complicated software to install for setup Configure NMEA data for 4800 or 38400 baud and set mode (TCP/IP or UDP) and port Set up with fixed or dynamic IP address Status page for system diagnostics Specifications: Power: 10-35V DC (Consumption approx. 50mA at 12V DC) Network Port: Ethernet RJ45 10/100MB IP Mode: Static or DHCP Operating Mode *TCP/IP or UDP; Support for up to 5 connected devices in TCP/IP mode; *Recommended mode of operation NMEA Input: Configurable 4800 or 38400 baud (NMEA 0183) NMEA 2000 option via iKonvertgateway Operating temp: -25 to +70 degrees C LED Indicators: Power -Status -Link -Data In -Data Out Options: RS232 connectivity (non-concurrent with NMEA) Dimensions (W x H): 95mm x 86mm

NavLink 2  “NavLink 2 is an easy to fit NMEA 2000 to Wifi server designed to make NMEA 2000 navigation data available for apps on smartphones, tablets, iPads and PCs.” Features: NavLink 2 is an easy to fit NMEA 2000 to Wifi server designed so that NMEA 2000 navigation data can be made available for apps on smartphones, tablets, iPads and PCs. Installation takes seconds as a result of direction connection to the NMEA 2000 back bone and self-powered from the data network. Once installed, it creates a local WiFi network for devices to connect or can be programmed to join an existing wireless network if one is already installed.  This is ideal for devices like the Furuno wireless radar which require operation through their own dedicated network but require NMEA 2000 data integration for charting apps. NavLink 2 now works with the popular Navionics Boating App for Apple iOS and Android. Therefore allowing display of GPS and AIS data on your Navionics charts.  Specifications: NMEA 2000 to WiFi server Self powered from NMEA 2000 bus – fits in seconds Supports TCP/IP and UDP connection modes Provides AIS, navigation and instrument data to apps Compatible with all popular apps like iNavX, TimeZero, Weather 4D, Navionics, SailGrib, NavLink, iSailor, SeaPilot, AquaMap etc Up to 7 connected devices Compatible with Windows, Linux, MAC OS, iOS and Android Easy web interface for programming Password protected Can act as dedicated wireless server or rather can connect to an existing wireless network Diagnostic data display mode and LED status lights Internal hi gain WiFi antenna Super-fast 230KBs operation Optional raw data mode for developers and likewise advanced users Supplied with NMEA 2000 cable

iKonvert NMEA 2000 Gateway with ISO Interface The iKonvert NMEA2000-0183 Gateway/Converter is an intelligent and flexible gateway for allowing new NMEA2000 equipment to talk to legacy NMEA0183 equipment. Conversions are bi-directional, so whether you want to get the data from older NMEA0183 sensors on to your NMEA2000 network or you have added a new NMEA2000 only MFD and want it to send GPS and Navigation data to your older NMEA0183 VHF and Autopilot, iKonvert will  accurately and intelligently carry out the required data conversions. There are many, many real life applications for NMEA2000 to NMEA0183, with a plethora of different makes and models of equipment that may need to be connected together. We have designed iKonvert to satisfy as many of these situations as possible by incorporating a simple but effective mode selection method, via a set of DIP switches inside iKonvert. Just remove two screws, open the iKonvert box and using a small screw driver, select the mode you need. The next time iKonvert powers up, it will automatically carry out the conversions you selected. A number of modes have already been defined including; Heading, Sounder, AIS, GPS, Wind, Instruments and an all data gateway mode, which automatically sets the conversions to be done and the baud rate iKonvert will use. What is more, if you need a mode that we have not defined yet, just let us know and we will consider including it. Digital Yacht’s iKonvert Gateway is housed in a compact and easy to mount housing, with an integral NMEA0183 cable and standard NMEA2000 Micro drop cable (male).  Taking its power from the NMEA2000 network, and providing full galvanic isolation between the NMEA0183 and NMEA2000 networks, iKonvert is the perfect solution for all NMEA conversions. For customers that want to take this converted data in to a computer, please consider the iKonvert USB gateway, that features an integral USB cable that is compatible with all of the popular operating systems (Windows/Mac/LINUX/Android). Features: Small but powerful bi-directional NMEA2000 to NMEA0183 Converter Powered from the NMEA2000 network Opto Isolated NMEA0183 Interface Converts AIS, GPS, Navigation, Instrument and XDR data Features “Real Life” data modes for most common installations Simple configuration of data modes using DIP switches Integral NMEA0183 cable and NMEA2000 Micro (Male) cables Full galvanic isolation

veKonvert NMEA 2000 Gateway veKonvert brings NMEA 2000 connectivity to Victron’s popular SmartShunt battery monitoring system. Now a navigation multi-function display becomes a sophisticated battery and energy management system. Features veKonvert is a stand-alone NMEA 2000 interface designed in conjunction with Victron Energy to integrate VE.Direct compatible devices such as their SmartShunt, BMV Battery Monitors, and MPPT Solar Charge Controller range into NMEA 2000 systems. This functionality already existed but required the use of a sophisticated Cerbo module. veKonvert is a lower-cost, simpler solution for smaller installations that just need the electrical data displayed on a multi-function display. Boaters and boat builders like a clear and uncluttered dash or nav area, so integrating electrical data into the main navigation display is a popular and cost-saving option. The product is a collaboration between Victron Energy and Digital Yacht. The system utilizes Victron’s proprietary VE.Direct data connectivity as a source for the NMEA 2000 data. Victron solar panel controllers (MPPTs) and battery monitors can now also interconnect to NMEA 2000 via the veKonvert interface. Installation Installation is simple – just "T" into the NMEA 2000 backbone and plug into the VE.Direct custom connector on the SmartShunt, and you've got battery and electrical data on your NMEA 2000 network! Specifications: Universal NMEA 2000 gateway for Victron products with a VE.Direct interface (see compatibility list in the FAQ tab) Enables battery management or solar charge monitoring on compatible multi-function displays (Raymarine, Garmin, Navico, Furuno, etc) Provides battery voltage, charge/discharge current, state of charge, and time to depletion based on a sophisticated algorithm Easy installation, plug ‘n’ play connectivity, and self-powering from the NMEA 2000 bus Generates NMEA 2000 alerts from any BMV or SmartShunt Alarms Supports multiple SmartShunts for a larger multi-battery system Vekonvert Is Compatible with the Following Victron Products: BMV -700, BMV -702, BMV -700H, BMV-712 Smart, BMV-710H Smart, BMV-712 Smart Rev2, SmartShunt 500A/50mV, SmartShunt 1000A/50mV, SmartShunt 2000A/50mV, and All MPPT Charge Controllers NOTE: veKonvert is not compatible with Victron Chargers and Inverters. It should also not be plugged into the VE.Direct interfaces of any Victron "Consumers" such as Multiplus, Quattro, Cerbo, etc.

OceanLink® 7" NMEA 2000® Certified TFT Gateway - Black The new OceanLink® 7" multifunction TFT Display features a 24-bit/16 m colors optically bonded display with transmissive layer technology for perfect readability even in direct sunlight. The TFT Display shows and distributes a wide array of data received from NMEA 2000® and J1939 CAN Bus systems and analog sensors directly connected to the display. Users can customize up to 40 data pages with single, double, treble, or quad grid layouts.  TFT Displays can be daisy-chained with other OceanLink® gauges, displays, or NavControls using the unique VDO Marine Bus or directly connected to the NMEA 2000® backbone (optional adapter cable required) for simple installation on any yacht.  Features: Touch screen function  Optically bonded mineral glass lens  Front & rear side protection rating IPX7  1x NMEA 2000® connector  2x J1939  6x Analog input  2x Frequency input  2x 4–20 mA  3x Digital input or 0–5 V  2x Alarm output  2x Video input  2x EasyLink data output  2x Programmable alarm output 500 mA  Operating temperature range -20°C/+70°C 12/24V WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

OceanLink® 4.3" NMEA 2000® Certified TFT Gateway - Black The new OceanLink® 4.3" multifunction TFT Display features a complete 24-bit/16 m colors optically bonded display with transmissive layer technology for perfect readability even in direct sunlight. The TFT Display shows and distributes a wide array of data received from NMEA 2000® and J1939 CAN Bus systems and analog sensors directly connected to the display. Users can customize up to 40 data pages with single, double, treble, or quad grid layouts.  TFT Displays can be daisy-chained with other OceanLink® gauges, displays, or NavControls using the unique VDO Marine Bus or directly connected to the NMEA 2000® backbone (optional adapter cable required) for simple installation on any yacht.  Features: Optically bonded mineral glass lens • Front & rear side protection rating IPX7  1x NMEA 2000® connector  1x J1939  2x Analog input  1x Frequency input  2x 4–20 mA output  1x EasyLink data output  1x Programmable alarm output 500 mA  Operating temperature range -20°C/+70°C 12/24V WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 T-Connector - 1-Way Extension Block As the NMEA 2000 network expands beyond the 3-device limit of Digital Yacht’s NMEA 2000 Starter Kit, users can use one of these single T-pieces to add devices. With male > female > female connectors, multiple T-pieces can be plugged together or added to the 4-way T-piece included in the starter kit. The lower “drop cable” connector is female so that there are no exposed pins when the drop cable is removed. *Digital Yacht can supply NMEA 2000 cables and connectors to expand the NMEA 2000 to whatever size is needed (up to the maximum 50 NMEA 2000 device limit). Features: NMEA 2000 Single T-Piece Standard “Micro C” connectors make it very easy for future network expansion Metal connectors improve reliability Waterproof rating of IP68

NMEA 2000 T-Connector - 6 Ports As the NMEA 2000 network expands beyond the 3-device limit of Digital Yacht’s NMEA 2000 Starter Kit, users can use this 4-way T-piece to add another four additional devices. With male > female > female connectors, multiple T-pieces can be plugged together or added to the 4-way T-piece included in the starter kit. Also, The 4x lower “drop cable” connector is female so that there are no exposed pins when the drop cable is removed. *Digital Yacht can supply NMEA 2000 cables and connectors to expand the NMEA 2000 to whatever size is needed (up to the maximum 50 NMEA 2000 device limit). Features: NMEA 2000 4 x T-pieces Standard “Micro C” connectors make it very easy for future network expansion Metal connectors improve reliability Waterproof rating of IP68

AISnode NMEA 2000 Boat AIS Class B Receiver AISnode is the first AIS Receiver to be designed exclusively for NMEA 2000. With a single, integral 0.75m NMEA 2000 cable that takes power from the network and outputs the AIS data on to the network, the AISnode is incredibly easy to install. Just find or fit a spare NMEA 2000 "T Piece", screw the AISnode cable to the connection, connect a VHF antenna and the installation is complete.  Utilizing the same high performance, true dual channel receiver that our latest Class B Transponders have, AISnode will receive every AIS equipped vessel within VHF range and never miss or drop a single target. All of the latest NMEA 2000 AIS message types are supported, including AIS SARTs, AtoNs and Class B static data, ensuring full compatibility with all of the latest AIS enabled chart plotters.  NMEA 2000 is becoming more and more popular on new boats and nearly all new chart plotters have an NMEA 2000 interface, with one or two models only providing an NMEA 2000 interface. With its reliability, easy plug and play connectivity and industry standard compatibility, it is not surprising why NMEA 2000 is gradually replacing the older NMEA0183 standard. The AIT2000 and AIT3000 Class B Transponders already provide NMEA 2000 connectivity but not all customers want the extra expense of purchasing and installing a transponder and for small chart plotters an AIS receiver is still a popular choice. Features: Application Domain: For Boats Type: Class B Receiver

0183 to N2K Gateway with PC Interface, ISO  The NGX-1 is an intelligent gateway that converts NMEA 0183 data to NMEA 2000 (and vice versa), allowing you to share information between devices from the two standards. This creates the possibility of upgrading some of the vessel’s electronics to NMEA 2000 and keeping the remaining NMEA 0183 devices. This can help spread the cost of transitioning to NMEA 2000, reducing the initial upgrade cost to accommodate a new NMEA 2000 device.  The ISO variant connects easily to NMEA 0183 devices with a dedicated pair of data wires for transmit and receive, allowing the NGX-1 to share data bi-directionally if required. OPTOIsolation is included on the input and groundbreaking ISO-DriveTM technology is on the output to keep your devices safe from hazardous ground loops.  The USB Variant allows for quick and easy connectivity to a PC running software that requires NMEA 0183 data. Thanks to the device being low power, it is powered directly from the NMEA 2000 network, removing the requirement for an independent power supply.  The Actisense NGX-1 also makes it possible to send and receive NMEA 2000 data safely between a PC and an NMEA 2000 network. This creates the possibility of feature-rich software applications replacing or complementing dedicated hardware such as a Multifunction Display (MFD) or Chart Plotter.  Acting as an NMEA 2000 to PC Gateway allows the device to act as a rule-enforcing firewall between the PC and the network, giving the user full control over what data is passed and blocked. The NGX is capable of transferring every currently available NMEA 2000 PGN from the network to a PC application. Features: ISO version has OPTO-isolated input and ISO-Drive output for safely interfacing with NMEA 0183 or RS232 / RS422. Advanced configuration using the Actisense Toolkit allows Tx / Rx lists and Tx rates to be set. Supports fast-heading at 10Hz. Up to 230,400 baud rate data transfer rate. Integrated 0.75m ISO cable. Diagnostic LEDs on both input and output. Integrate Seamlessly with Raymarine® Products The STNG-A06045 adaptor cable enables users to integrate Raymarine SeaTalkNG products into the standard configured NMEA 2000® bus and vice-versa. Currently only available when purchased with an Actisense NMEA 2000® Gateway product.

0183 to N2K Gateway with PC Interface, USB The NGX-1 is an intelligent gateway that converts NMEA 0183 data to NMEA 2000 (and vice versa), allowing you to share information between devices from the two standards. This creates the possibility of upgrading some of the vessel’s electronics to NMEA 2000 and keeping the remaining NMEA 0183 devices. This can help spread the cost of transitioning to NMEA 2000, reducing the initial upgrade cost to accommodate a new NMEA 2000 device.  The ISO variant connects easily to NMEA 0183 devices with a dedicated pair of data wires for transmit and receive, allowing the NGX-1 to share data bi-directionally if required. OPTOIsolation is included on the input and groundbreaking ISO-DriveTM technology is on the output to keep your devices safe from hazardous ground loops.  The USB Variant allows for quick and easy connectivity to a PC running software that requires NMEA 0183 data. Thanks to the device being low power, it is powered directly from the NMEA 2000 network, removing the requirement for an independent power supply.  The Actisense NGX-1 also makes it possible to send and receive NMEA 2000 data safely between a PC and an NMEA 2000 network. This creates the possibility of feature-rich software applications replacing or complementing dedicated hardware such as a Multifunction Display (MFD) or Chart Plotter.  Acting as an NMEA 2000 to PC Gateway allows the device to act as a rule-enforcing firewall between the PC and the network, giving the user full control over what data is passed and blocked. The NGX is capable of transferring every currently available NMEA 2000 PGN from the network to a PC application. Features: Vital NMEA 2000 diagnostic tool. USB version is fully isolated to prevent dangerous ground loops. Up to 230,400 baud rate data transfer rate. Integrated 1.8m USB cable. Diagnostic LEDs on both input and output. Integrate Seamlessly with Raymarine® Products The STNG-A06045 adaptor cable enables users to integrate Raymarine SeaTalkNG products into the standard configured NMEA 2000® bus and vice-versa. Currently only available when purchased with an Actisense NMEA 2000® Gateway product.

Engine Link NMEA 2000 Engine Monitor ENGINELink interface is an NMEA 2000 wireless device that allows mobile phones, iPads, and tablets to display engine data as well as provide a link to boat AIS, depth, and GPS information for popular apps such as Navionics, NavLink, iNavX, SavyNavy, AquaMaps and 100's more. Now boaters can have boat engine data plus their favorite charting app displayed on their mobiles and tablets in real-time. Engine information such as RPM, temperature, pressure, and battery voltage is displayed as an attractive dashboard display through the web browser so there’s no need for a custom app. Setup and installation are easy. Just “T” into the boat's NMEA 2000 backbone and ENGINELink is self-powered from the network. It creates a secure, password-protected local wifi network with up to 7 devices able to connect simultaneously. UDP and TCP-IP protocols are supported for compatibility with 3rd party apps. Either single or dual-engine installations are supported. If the vessel is fitted with NMEA 2000 compatible trim tabs or jack plates, then the status of these performance-critical systems is also displayed on the dashboard. You can configure ENGINELink through its own simple web interface - just open your web browser, enter its IP address and you'll access the attractive dash to display and configure your gauges. No complicated programming software or app is required. iOS and Android devices can display a navigation app and a web browser side by side - so you can have your favorite charting app open alongside engine instrument displays. You can change the network name & password and even merge the wifi to an existing wifi network on board. NMEA 2000 data can be viewed and logged in the web browser allowing for easy fault finding of issues. If the engine generates diagnostic alerts then these can be displayed and interrogated too. Features: Connect to any NMEA 2000-ready engine or network Built-in web gauge display – no app needed Display single or dual-engine gauges Configurable gauges – choose the parameters you want to monitor Set alarm/alert thresholds and view diagnostics TCP/UDP streaming of navigation data (GPS/AIS/Depth) for popular navigation apps Tank levels, fuel flow, and trip computer-type displays Tilt, trim tabs, and jack plate support Manufacturer-specific engine modes Specifications: Powered from NMEA 2000 Network – fits in seconds Password-protected wireless interface 802.11b/g/n AP or STA mode (can join another boat wifi network) TCP/UDP streaming of navigation data (AIS, GPS, and depth) to popular apps like Navionics, TZ, AquaMaps, iNavX etc Supported PGNs (1st Release) 127488, 127489, 127493, 130312, 130316, 127505, 130576, 128780 Preset gauge displays for leading manufacturers or customize your display Flexible, upgradeable interface Target Markets & Applications: Brings boat engine data to mobile devices Primarily aimed at the US center console and sports fishing market where outboard-powered craft have NMEA 2000 networks with engine data available but will work with any NMEA 2000 ready engine installation – inboard or outboard Provides additional data displays and extra functionality than MFDs Low-cost dashboard repeater accessible anywhere onboard Ideal test tool for service technicians Will be at the leading edge of electric propulsion PGN implementation Logging and replay of data for onshore analysis Support for the latest jack plate and trim tab PGNs, for optimizing boat performance Connects to Navionics app (and 100s more) for AIS, GPS, and depth data

NMEA 2000 1M Drop Cable This Digital Yacht cable is a 1m (3ft) NMEA 2000 drop cable made of metal connectors for maximum reliability. The drop cable allows users to expand the NMEA 2000 to whatever size is needed. *Digital Yacht “Drop Cables” can also be used as backbone cables and are easily connected to make any length of backbone cable required. Also, the total length of all drop cables must be less than 76m. Features: 1m (3ft) NMEA 2000 Drop Cable Standard “Micro C” connectors make it very easy for future network expansion Metal connectors improve reliability Waterproof rating IP68

NMEA 2000 3M Drop Cable This Digital Yacht cable is a 3m (9ft) NMEA 2000 drop cable made of metal connectors for maximum reliability. The drop cable allows users to expand the NMEA 2000 to whatever size is needed. *Digital Yacht “Drop Cables” can also be used as backbone cables and are easily connected to make any length of backbone cable required. Also, the total length of all drop cables must be less than 76m. Features: 3m (9ft) NMEA 2000 Drop Cable Standard “Micro C” connectors make it very easy for future network expansion Metal connectors improve reliability Waterproof rating IP68