Straps Support System with Support Pole Eliminates virtually all possible areas that could collect water and allow it to pool, causing damage to the cover. This system is designed for simplicity with two pre-installed, adjustable 20-foot straps that snap quickly to the rear tow hooks and one 40-foot adjustable strap to cradle the bow.  System fits up to 28-foot boats.  For pontoon boats, two systems are required and can easily be joined to create a perfect “frame” for the pontoon cover.  Each system comes with one adjustable (40″ to 70″) support pole, system center, strap set and simple installation instructions.

RayStar 150 GPS Sensor w/Pole Mount RS150 GPS Sensor The RS150 GPS is a high performance, 72-channel, remotely mounted GPS sensor for Raymarine navigation systems. The RS150 offers fast 10Hz position updates and enhanced accuracy. The RS150 is also a GNSS receiver and supports the GLONASS global navigation satellite system. Features: 72-channel GPS receiver Fast 10Hz position updates Satellite differential GPS-compatible. Space-Based Augmentation System (SBAS) enabled with WASS, EGNOS, MSAS and GAGAN support A GNSS receiver with GLONASS compatibility Low power consumption: 30mA (1 LEN) SeaTalkng and NMEA2000 compatible (using a device net adapter cable) Designed for low profile surface mounting or optional pole mounting Specifications: Nominal supply voltage: 12V D.C. Powered by N2K bus Operating voltage range: 8 - 32V DC Power consumption: 30 mA max (NMEA LEN = 1) Operating temperature: -13ºF to 131ºF (-25ºC to +55ºC) Relative humidity: max 93% Waterproof: IPx6/7 Supported connection protocols: SeaTalkng: NMEA 2000 (certified) (via DeviceNet adaptor) Sensitivity: High sensitivity - acquisition down to -163dBm No. of channels: 72 Positioning System: GPS & GLONASS Satellite Differential Type: WAAS (United States); EGNOS (Europe); MSAS (Japan); GAGAN (India) Differential acquisition: Automatic Position accuracy (95%): <15M Position accuracy with SDGPS (95%): <5M Speed accuracy (95%): <0.3kt Time to first fix from cold start: <2 minutes (< 45 seconds typical) Time to first fix from hot start: < 8 seconds -72 hour hold up battery allows for hot start Geodetic Datum: WGS84 Pole Mount for RS150 GPS Antenna Raymarine's Pole Mount specifically for the RS150 GPS Antenna. The RS150 has 72 channels and offers faster 10Hz performance and enhanced accuracy. The RS150 is also a GNSS receiver and supports the GLONASS global navigation satellite system.

Pontoon Boat Cover Support System Extend the life of your pontoon boat cover by preventing water from pocketing. This easily installed system includes two adjustable support poles (bright dip anodized-snap ends). Poles adjust from 27" to 50" maximum height. 60ft of 1" polypropylene webbing, quick release adjuster buckles and four injection molded hooks to secure to decking. 

C Frame Magnetic Circuit Breaker - 50 Amp - Double Pole - White Features: 50 Amp Double Pole Standard Circuit Breakers for Paneltronics electrical distribution panels Meets all American Boat and Yacht Council (ABYC) Standards for non-ignition protected circuit breakers UL Recognized (UL 1077) for use in the U.S.A., and CSA Certified for use in Canada CE compliant Circuit Breakers are VDE Approved for use in Europe Trip free (ABYC E-11.12.1.7.2.2.) Manual reset (ABYC E-11.12.1.7.2.4.)

C - Series Flat Circuit Breaker, Single and Double Pole PN:   7476 Amperage:   200 Amp Features: Color actuator indicates "OFF" position "Trip Free" design cannot be held "ON" during fault current condition Flat actuator protects against accidental switching Specifications    Circuit Breaker Type Magnetic Hydraulic - Trip Free Maximum Voltage 80 Volts DC Rated Switch Cycles 10,000@rated amperage and voltage WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

C - Series Flat Circuit Breaker, Single and Double Pole PN:   7477 Amperage:   250 Amp Features: Color actuator indicates "OFF" position "Trip Free" design cannot be held "ON" during fault current condition Flat actuator protects against accidental switching Specifications    Circuit Breaker Type Magnetic Hydraulic - Trip Free Maximum Voltage 80 Volts DC Rated Switch Cycles 10,000@rated amperage and voltage WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

"C" Frame Magnetic Circuit Breaker 60 Amp Double Pole Standard Circuit Breakers for Paneltronics electrical distribution panels Meets all American Boat and Yacht Council (ABYC) Standards for non ignition protected circuit breakers UL Recognized (UL 1077) for use in the U.S.A., and CSA Certified for use in Canada CE compliant Circuit Breakers are VDE Approved for use in Europe Trip free (ABYC E-11.12.1.7.2.2.) Manual reset (ABYC E-11.12.1.7.2.4.)

i4P Linear System w/17.7" Reflector & Universal Quad LNB With its rugged, reliable and durable design, the Intellian i4 provides the most outstanding performance to stay locked in. It connects boaters to the premium satellite TV entertainment they want while vessels are cruising at high speed or in rough sea conditions. The i4's stylish and polished dome design makes it perfect for boats over 50 feet. With its patent pending innovations in Wide Range Search (WRS) and Dynamic Beam Tilting (DBT) technologies, the i4 can achieve the most precise tracking performance and highest signal reception without the need of a fragile or superfluous motion sensor. An embedded GPS system can speed up satellite search and acquisition time. The revolutionary design feature of the i4 is that it has the intelligent built-in HD and TriSat modules in its control unit. This offers boaters High Definition satellite TV broadcasts from leading satellite TV service providers without any extra conversion tools and cable wiring. Using Dish Network or Bell TV in Canada, the standard i4 enables HD channel viewing, with DirecTV SD programing is available. For DirecTV HD consider the Intellian s6HD. Combined with the new built in WiFi enables simple one-touch upgrades using the Aptus App. With the Intellian MIM Switch (M2-TD02) sold separately, boaters can enjoy flipping channels through automatic satellite switching just like a home system. See the installation guide of DISH Network MIM for further details. For easy and flexible installation and operation, the i4 supports standard dual and quad IRD connections with its single cable design between the antenna and the antenna control unit (ACU). This simple and powerful system is manufactured in compliance with the most rigorous quality verification of ISO 9001:2001. Features: Fully Automated System Automatic satellite search and identification function 2-axis step motor for controlling the antenna pedestal High Quality Antenna 45 cm diameter of parabola-type antenna for receiving Ku-Band (10.7 12.75GHz) satellite signal LHCP/RHCP or Horizontal/Vertical polarization Enabling powerful signal gain Superior Dynamic Tracking Dynamic Beam Tilting (DBT) by rotating sub-reflector with high speed BLDC motor Fastest Search Algorithm Wide Range Search (WRS) algorithm Statistical search algorithm DVB (Digital Video Broadcasting) Signal Identification High speed identification employing DVB decoder QPSK demodulator lock for DSS signal Built-in GPS System Embedded GPS, which allows for the system to upload the GPS data automatically into the system New Antenna Control Unit Easy satellite information change and update via WiFi using the Aptus App Easy antenna status check and automatic diagnosis Easy antenna control using Aptus graphical control App Reliable power supply to the antenna and to the MIM module Embedded HD module and TriSat function Industry leading 3-year parts and workmanship guarantee with a 2-year labor warranty for all antenna systems, ensuring peace of mind with your hardware investment All Satellite Systems include the following parts as standard: Antenna & Radome 17.7" (45 cm) Reflector & North Americas LNB ACU (Antenna Control Unit) with WiFi connection for upgrades Built-in HD Module for Ku-Band HD (when available) Built-in GPS and NMEA 0183 GPS interface Built-in Pre-programmed Global satellite library Aptus App, downloadable Installation & Operation Manual Installation Template Quick Installation Guide Cable Kit: 49ft (15 m) x 1EA Antenna-ACU RG6 Coaxial Cables 10ft (3 m) x 1EA ACU-IRD RG6 Coaxial Cables 33ft (10 m) x 1EA DC ACU Power Cable 6ft (1.8 m) x 1EA PC Serial Cable This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

"C" Frame Magnetic Circuit Breaker 100 Amp Triple Pole Standard Circuit Breakers for Paneltronics electrical distribution panels Meets all American Boat and Yacht Council (ABYC) Standards for non ignition protected circuit breakers UL Recognized (UL 1077) for use in the U.S.A., and CSA Certified for use in Canada CE compliant Circuit Breakers are VDE Approved for use in Europe Trip free (ABYC E-11.12.1.7.2.2.) Manual reset (ABYC E-11.12.1.7.2.4.)

PED4400-C PedestalPod Uncut (Usable Face = 8.75"W x 6"H) (22.2cm W x 15.2cm H) - Carbon Black PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your fishfinder/chartplotter from the harshest of wet boating conditions. PedestalPods provide the convenience of easily reaching and controlling the fishfinder/chartplotter while providing added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20" off the deck and located near the bow and at the 45° angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal keeping spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the NavPod. The heavy duty, powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look and provides protection for wires and electrical connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. There are pre-cut models available for 7", 9" and 12" LCD displays from all major marine electronic manufacturers. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Auto Glide Boat Leveling System for Single Actuator Tab Systems w/Existing NMEA 2000 A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box, the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Single Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30255-001 Auto Glide Control Box f/ Single Actuator 1 30248-001 Auto Glide Control Box Harness f/ Single Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki E Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Lenco Auto Glide Boat Leveling System f/Dual Actuator Tab Systems w/Existing NMEA 2000 A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30256-001 Auto Glide Control Box f/ Dual Actuator 1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RAM EZ-Strap Rail Mount w/Universal X-Grip Cell Phone Holder The RAP-SB-187-UN7U consists of the RAM EZ-Strap base, double ball SHORT arm and universal X-Grip holder. The strap can be cut to fit tubing, square rails and irregular shapes from 0.5" to 2.58" in diameter. Multiple adjustment points allow you to move the universal X-Grip holder to your optimum viewing position. This mount rotates 180 degrees. Compatible Devices (WITH OR WITHOUT CASE): Apple iPhone 6 Apple iPhone 5s Apple iPhone 5c Apple iPhone 5 Apple iPhone 4S Apple iPhone 4 Apple iPhone 3GS Apple iPhone 3G Apple iPhone Apple iPod touch (All Models) Apple iPod (G1-G5) Samsung GALAXY S4 Samsung GALAXY S5 The X-Grip holder is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. Holder Dimensions: Minimum Width = 1.875" Maximum Width = 3.25" Depth = 0.875" Features: 1. Rustproof 2. High strength composite and stainless steel construction 3. Spring loaded holder expands and contracts for perfect fit of your device 4. Rubber coated tips will hold device firm and stable 5. Versatility of holder allows for attachment to many RAM-to-RAM ball mounts 6. Single socket technology allows for multiple adjustment angles and articulation of device 7. Lifetime warranty Material: High Strength Composite & Stainless Steel Note: The "U" in the part number reflects product packaged in poly bag.

LiveScope™ XR System w/GLS 10™ & LVS62 Transducer  THE BEST OF THE BEST JUST HIT THE OPEN WATER You didn’t think it could get better, but it did with the extended range of the LiveScope XR System. It’s the latest in LiveScope technology, now for coastal and open-water fishing. Features: Explore the deep with an extended range up to 500’ in freshwater and 350’ in saltwater.  Find fish circling your boat with clear views close around your hull. Upgrade your current LiveScope System black box (GLS™ 10 sonar module) with just a new transducer.  Get maximum contrast and clarity in your images with vivid color palettes.  Don’t miss a thing with supported Forward, Down and Perspective modes plus necessary mount.  The Long View The Reverse Range Offset feature uses more of the screen to display fish and structure up to 500’ in freshwater and 350’ in saltwater. A Close View The Compress Range feature gives you a clear view close to your boat while keeping an eye on targets farther away. Real-Time Images  Real-time sonar ensures that your live images are as accurate as possible. Image Stabilization  A built-in stabilization system keeps the sonar image on your compatible chartplotter steady, even in rough conditions. Vivid Color Palettes  Choose from seven vivid color options — including aqua, Caribbean, lava and more — to see fish and structure in maximum contrast and clarity. Forward Mode  Now scout even farther ahead of your boat to see what’s happening in real time. Down Mode  Explore live views of the activity deeper beneath your boat. Perspective Mode  See under the water with a view from your perspective above the water. In The Box: LiveScope GLS 10 sonar black box LiveScope XR LVS62 transducer Perspective mount (LiveScope XR LVS62 transducer only) Trolling motor barrel mount Shaft mount Power cable 2 meter Garmin Marine Network cable (small connector) Network adapter cable Documentation 

i6P Linear System w/23.6" Reflector & Universal Quad LNB Must Ship Truck Freight The Intellian i6 provides superior tracking performance and efficiency compared to antenna systems in similar size. With its stylish dome, the i6 is ideal for boats over 65 feet. The i6 brings boaters the excitement and variety of satellite TV programs while the vessels are traveling around coastal or blue water regions, the larger reflector size of the Intellian i6 increases the range that the unit will operate. You will never have to compromise on reception or quality. The i6 offers the highest signal strength available along with Intellian patented innovations, Wide Range Search (WRS) and Dynamic Beam Tilting (DBT) technologies. Therefore, the i6 can always offer the most precision tracking capabilities and superior satellite signal reception while the vessel is cruising at high speed or in rough sea conditions. The most innovative design of i6 is the integrated smart HD and TriSat modules in the antenna control unit (ACU) which allows boaters to access their favorite HDTV channels from leading satellite TV service providers freely just like they are used to do at home. Combined with the new built in WiFi enables simple one-touch upgrades using the Aptus App. The i6 brings you trouble-free installation and operation with its single cable design between the antenna and the control unit. With the Intellian MIM Switch(M2-TD02) sold separately, boaters can enjoy changing Dish Network HD channels with automatic satellite switching just like a home system. See the installation guide of DISH Network MIM for further details. Plus, the Intellian i6 has a built-in GPS system to enhance satellite acquisition time and accuracy. For DirecTV users the Intellian i6 offers the full range of SD channels, upgrade to the Intellian s6HD for HD programing from DirecTV. Features: Fully Automated System Automatic satellite search and identification function 2-axis step motor for controlling the antenna pedestal High Quality Antenna 23.6 inch (60 cm) Reflector antenna for receiving Ku-Band (10.7 12.75GHz) satellite signal LHCP/RHCP or Horizontal/Vertical polarization Enabling powerful signal gain Superior Dynamic Tracking Dynamic Beam Tilting (DBT) by rotating sub-reflector with high speed BLDC motor Fastest Search Algorithm Wide Range Search (WRS) algorithm Statistical search algorithm DVB (Digital Video Broadcasting) Signal Identification High speed identification employing DVB decoder QPSK demodulator lock for DSS signal Built-in GPS System Embedded GPS, which allows for the system to upload the GPS data automatically into the system New Antenna Control Unit Easy satellite information change and update via WiFi using the Aptus App Easy antenna status check and automatic diagnosis Easy antenna control using Aptus graphical control App Reliable power supply to the antenna and to the MIM module Embedded HD module and TriSat function Industry leading 3-year parts and workmanship guarantee with a 2-year labor warranty for all antenna systems, ensuring peace of mind with your hardware investment All Satellite Systems include the following parts as standard: Antenna & Radome 23.6" (60 cm) Reflector & Linear LNB ACU (Antenna Control Unit) with WiFi connection for upgrades Built-in HD Module for Ku-Band HD (when available) Built-in GPS and NMEA 0183 GPS interface Built-in Pre-programmed Global satellite library Aptus App, downloadable Installation & Operation Manual Installation Template Quick Installation Guide Cable Kit: 49ft (15 m) x 1EA Antenna-ACU RG6 Coaxial Cables 10ft (3 m) x 1EA ACU-IRD RG6 Coaxial Cables 33ft (10 m) x 1EA DC ACU Power Cable 6ft (1.8 m) x 1EA PC Serial Cable This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.