Cable Cutter to 1/4" - Felco C. Sherman Johnson Hand Crimp Fittings have proven themselves over the years, however the overall integrity of the system depends on the proper tools for the job. The tools are designed with special width and relief patterns which apply to Johnson hand crimp fittings and instructions only .The use of other tools or crimping fittings other than Johnson hand crimp fittings with Johnson tools can result in failure of the terminal, personal injury or loss of life.  This specific tool will give you a clean, crisp cut through 1/4" sized cables. Swiss made.

C-12 Cutter to 3/8" - Felco C. Sherman Johnson Hand Crimp Fittings have proven themselves over the years, however the overall integrity of the system depends on the proper tools for the job. The tools are designed with special width and relief patterns which apply to Johnson hand crimp fittings and instructions only .The use of other tools or crimping fittings other than Johnson hand crimp fittings with Johnson tools can result in failure of the terminal, personal injury or loss of life.  This specific tool will give you a clean, crisp cut through 3/8" sized cables.

Hinged Pad Eye- 1/4" C. Sherman Johnson Pad Eyes fold flat when not in use. The eye gives with the load unlike rigid pad eyes; material reducing the load on the fastenings. A friction drag insures that the eye stays in position and is rattle free.  Specifications: T-316 Stainless Steel construction Supplied with backing plate

Quick Release Pin - 1/4" x 1" Specifications: Diameter: 1/4" Grip Length: 1" Use with: 14-205 and 14-206

March 893-10-1/4" 24V Pump W/ 1286-0002-0100

BURKS GNA6-1 1/4-5.00, CENTRIFGUAL PUMP ONLY BRONZE-FIT Bronze Fitted Cast Iron Construction. Base mounted Pump Only less Motor. Ports are Inches NPT Inlet, Inches NPT Outlet.   UNSPSC Code: 40150000

BURKS T310GA5-1 1/4, CENTRIFUGAL PUMP 3PH 1HP TEFC Close Coupled, 60 Hz, Three Phase, 3500 RPM, 1 Horsepower, TEFC Motor Enclosure, Frame Size 56J.   UNSPSC Code: 40150000

Ampco KC2 1 1/4 X 1, Fluid End Aluminum Bronze 56J Frame

Bosworth 75-1 1/4 Foot/Check Vlv 1 1/4 Female   Bosworth- Foot Valve / Check Valve Sea-Lect Gray Delrin, Buna Flapper Valve, 1 1/4” Female Threaded Ports

Burks T37G5-1 1/4-SS-3.25, Centrifugal Pump 80gpm, 1-1/4" Outlet 3/4HP 3PH

BURKS 310G5-1 1/4, BURKS CIRCULATION G5 PUMP 230-440V 1HP 3PH Centrifugal Pump and Motor unit. Bronze Fitted Cast Iron Construction. Close Coupled to a 1 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.25 Inches.

BURKS 315G5-1 1/4, Centrifugal Pump 3PH 1 1/2HP 230/460v Bronze Fitted Cast Iron Construction. Close Coupled to a 1-1/2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.75 Inches.

BURKS 315GA5-1 1/4, Centrifugal Pump 230/460v 3PH 1 1/2HP BF All BRONZE Construction. Close Coupled to a 1-1/2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.56 Inches.

BURKS 320G6-1 1/4, CENTRIFUGAL PUMP 230/460v 3PH 2HP Bronze Fitted Cast Iron Construction.   Close Coupled to a 2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 5.13 Inches

BURKS 320GA5-1 1/4, Bronze Fitted Cast Iron Centrifugal Pump 230/460v Bronze Fitted Cast Iron Construction. Close Coupled to a 2 Horsepower, 3450 RPM, 230/460 Volts, 3 Phase Motor. Ports are 1-1/2 Inches NPT Inlet, 1-1/4 Inches NPT Outlet. Impeller Diameter is 4.88 Inches.   Burks end suction, three phase, close-coupled, bronze fitted, centrifugal pump with mechanical seal. They are ideal for booster service, recirculation, general water supply, and washer lines.   Construction: Casing and bracket are close grain cast iron. Enclosed 4-7/8" bronze impeller, 302 stainless steel motor shaft, single mechanical seal, carbon faces, buna elastomers, 304 stainless steel metal parts.  Connections: 1-1/2" X 1-1/4" female NPT suction and discharge Motor: 2 HP, 3450 RPM, Open drip proof, three phase, 208/230/460 volts, 60 Hz, ball bearings front and back, built-in overload protection.    Clockwise rotation, when facing back of motor. Maximum working pressure: 200 PSI Maximum inlet pressure: 70 PSI Maximum working temperature: 180 degrees Fahrenheit Carton dimension: 14" high, 12" wide, 24" long.   Please Contact us for shipping quote at http://www.clrmarine.com/Contact_Us