|
Continuous Duty Solenoid - 12V
Minimizes arcing and contact oxidation, maintains highp erformance. Universal use with part numbers available to handle loads up to 200A.
PVC Coated option available for a more environmentally sealed product. Coated solenoids withstand moisture and dust to IP66.
Mechanical Specifications:
SPST Normally open contacts
Plated steel housing. Hexnuts and washers included
Large (power circuit) battery studs; copper
5/16” -24 thread
Small (control circuit) coil studs; steel 10-32 thread
Bracket mounting holes 5/16 X 19/32” (7.9 X 15.1mm) on
2 13/64” centers (56.0mm)
Available with PVC coated exterior or Potted Coil interiors
for harsh environments or vibration resistance
Caution: Never unscrew the inner hexnuts on the studs
These keep the stud and inner wiring in place
|
32.28 |
|
|
Continuous Duty Solenoid 65 Amp 12V UL Listed
Relays are commonly referred to as a remote-acting switches and Littelfuse manufacturers a broad range of styles to meet your application. To ensure you are utilizing the proper remote-acting switches, review the attributes in the specifications tab below against your application requirements.
Features:
65 Amp
12V
Copper Contact Stud Material
Steel Coil Stud Material
Normally Open Contacts
|
37.37 |
|
|
Continuous Duty Solenoid - 200A - 12V
Relays are commonly referred to as remote-acting switches and Littelfuse manufacturers a broad range of styles to meet your application. To ensure you are utilizing the proper remote-acting switches, review the attributes in the specifications tab below against your application requirements.
Specifications:
Current Rating (Continuous) in Amps: 200
Circuitry: SPST
Normal Position: Normally Open
Contact Material: Silver
Housing: Plated Steel
|
79.61 |
|
|
Continuous Duty Solenoid - 12V - PVC Coated
Features:
Hex nuts and lock washers are included
Steel housing mounting holes: 5/16 x 19/32,” 2 13/64” on centers (7.9 x 15.1, 56.0mm)
Plated steel housing available with optional PVC coating available to protect critical components from environmental hazards
12 Volt
PVC Coated
65 Amps
Insulated
Contact: Copper
UL Listed
|
43.52 |
|
|
65A PVC Coated Continuous Duty Solenoid
Remotely switch high amperage loads with a low amperage on-off switch.
Features:
Continuous duty, 65A at 12V DC
Intermittent rating 100A: 10 seconds
Copper #10-32 thread signal terminals
Copper 5/16”-24 thread contact terminals
PVC coated steel case
Bracket mounting holes 5/16” x 19/32”, 2-13/64” on centers
UL and CE approved
Same as Cole Hersee part number 24117-01
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
36.22 |
|
|
85A Remote Switching Continuous Duty Solenoid
Can be used with Electro-Scan MSDs and other high-amp circuits with remote operation.
Features:
Continuous duty, 85A at 12V DC
Intermittent rating 750A make/100A break, 10 seconds On, 30 minutes Off
Insulated ground
Steel housing, brass hardware
UL listed and CE certified
Same as Cole Hersee part number 24059
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
26.86 |
|
|
65A Remote Switching Continuous Duty Solenoid
Remotely switch high amperage loads with a low amperage on-off switch.
Features:
Continuous duty 65A, Intermittent duty 100A (10 Sec.)
Copper #10-32 thread ignition and ground terminals
Copper 5/16"-24 thread contact terminals
Plated steel case, copper contacts
Hexnuts and washers included
Bracket mounting holes 5/16" x 19/32", 2-13/64" on centers
UL and CE approved
Same as Cole Hersee part number 24059-08
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
30.89 |
|
|
Continuous Duty Solenoid (CDS)
Raritan's Continuous Duty Solenoid is a toilet replacement part.
Raritan manufactures equipment for pleasure boats throughout the world. Products include marine toilets, waste treatment systems, icemakers and water heaters. Committed to the environment and preserving sea life, Raritan designs products to help maintain an environmental balance and ensure the quality of marine waters.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
55.38 |
|
|
Intermittent Duty Reversing Solenoid - 12V DPDT
A combination of two solenoids in one package to reduce cost and maximize space savings while also providing simpler wiring. Two integral solenoids provide dynamic braking for permanent magnet motors when neither coil is energized. This intermittent duty solenoid can be used at a variety of amperages.
Specifications:
75A Make/Break: 5 min On, 5 min Off
125A Make/Break: 30 sec On, 5 min Off
150A Make Break: 0.5 sec On, 5 min Off
Circuitry: DPDT
Contact Material: Copper
Housing: Plastic
|
104.16 |
|
|
Heavy Duty Toggle Switch DPST On-Off 4-Screw
Cole Hersee's Heavy Duty DPST Toggle Switch, 4 Screw Terminals, 25 A Standard or long handle. Universal application. Silver contacts. Mounting stem is nickel-plated brass 15/32" -32 thread, 15/32" (11.9mm) long, and fits panels up to 9/32" (7.1mm) except where stated otherwise. phenolic housing, with plated steel cap. Nickel-plated brass mounting hardware. Blade terminals: .250 quick connect. Screw terminals: 6-32 screws. 25A at 12V, 15A at 24V, and 10A at 36V DC.
|
10.81 |
|
|
COLE HERSEE
Littelfuse acquired Cole Hersee to offer customers a more extensive portfolio of products in the commercial vehicle market. Cole Hersee is a pioneer and leader in the development of heavy-duty electrical products for the vehicle industry, and have earned a reputation for quality and value.
|
|
|
100A Engine Starting Intermittent Duty Solenoid
Intermittent switching of high amperage loads with a low amperage on-off switch.
Features:
Rated at 750A make/100A break, this solenoid is for intermittent use only: 10 seconds ON, 20 minutes OFF (ideal for engine cranking)
Signal voltage of 12V DC and contact voltage of 6-12V DC
#10/32 thread signal terminals
Copper 5/16”-24 thread contact terminals
Bracket mounting holes 5/16” x 19/32”, 2-13/64” on center
Same as Cole Hersee part number M-200
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
23.58 |
|
|
Heavy-Duty Toggle Switch SPST On-Off 2-Wire
Toggle Switches are designed for universal applications within harsh environments. Their mounting, body, and actuator features are designed for ease-of-use and extended product lifecycle. The Standard Heavy Duty Toggle Switch Series is our most robust series of toggle switches, available in several configurations of actuators and circuitries.
Specifications:
Mounting: Nickel Plated Brass Face Nut through 15/32 (11.90mm) Panel Hole *Part Number 5520: Black Finished Face Nut
Voltage Ratings: 10A at 36V DC/15A at 24V DC/25A at 12V DC
Current Rating (Continuous) in Amps: 10
Voltage Rating (Max): 36
Circuitry: SPST
Input Terminals: 2 Leads (203mm 16AWG Stripped) 1 Plug - 2 Leads (203mm 6AWG Stripped) 1 Plug
Housing: Weather-Resistant PVC-Coated Plasticized Housing
Actuator: Standard Toggle
Actuator Details: Nickel-Plated Brass - 17.4625
Panel Thickness: Up to 1/4 (6.35mm) thick
Contact Material: Silver
Recommended Torque: On - None - Off
|
17.29 |
|
|
Heavy Duty Toggle Switch SPST On-Off 2 Screw
Standard or long handle. Universal application. Silver contacts. Mounting stem is nickel-plated brass 15/32" -32 thread, 15/32" (11.9mm) long, and fits panels up to 9/32" (7.1mm) except where stated otherwise. phenolic housing, with plated steel cap. Nickel-plated brass mounting hardware. Blade terminals: .250 quick connect. Screw terminals: 6-32 screws. 25A at 12V, 15A at 24V, and 10A at 36V DC.
|
6.96 |
|
|
Heavy Duty Toggle Switch SPST On-Off 2 Blade
Standard or long handle. Universal application. Silver contacts. Mounting stem is nickel-plated brass 15/32" -32 thread, 15/32" (11.9mm) long, and fits panels up to 9/32" (7.1mm) except where stated otherwise. phenolic housing, with plated steel cap. Nickel-plated brass mounting hardware. Blade terminals: .250 quick connect. Screw terminals: 6-32 screws. 25A at 12V, 15A at 24V, and 10A at 36VDC.
|
6.97 |
|