|
G1 Satellite Compass - NMEA 0183 with 15M Cable
Accurate Heading, Position & Rate of Turn
Features:
Supports both GPS and GLONASS satellites for complete redundancy
Heading accuracy < 0.25° rms
Position accuracy < 0.3m 95% confidence (DGPS)
An integrated 9 Axis Inertial Measurement Core (IMC technology) provides
enhanced roll, tilt and heading stability even during momentary loss of
satellite signals
G3 color display system (optional)
Engineered enhancements to exceed sealed IP67 rating
Extended 2 year warranty
NMEA 2000® interface
Heave, Pitch, Roll and Rate of Turn as standard output
Heading updates 1 to 20 Hz
BAUD Rate selectable: 4800, 9600, 19200, 38400,115200
Fully compatible with on board NMEA 0183 RADAR, ECDIS, AIS, Cameras,
SONAR, PC and Autopilots
Compact integrated surface mounting (Pole mount optional) IMO Compliant, Wheelmark and USCG approved
Pre-programmed default settings for Heading, Rate of Turn, Course over
Ground, Lat/Long position, Time & Date
15 meter serial cable standard (30 meter optional)
6 meter NMEA 2000® Cable (optional)
CE certified for EMI and RFI immunity
Worldwide service
|
2198.23 |
|
|
G2 Satellite Compass - NMEA 0183 with 15M Cable
Accurate Heading & Precise Position for Professionals
Features:
Supports both GPS and GLONASS satellites for complete redundancy
Heading accuracy < 0.25° rms
Position accuracy < 0.3m 95% confidence (DGPS)
An integrated 9 Axis Inertial Measurement Core (IMC technology) provides enhanced roll, tilt and heading stability even during momentary loss of satellite signals
IMO Compliant G3 color display system (optional)
Engineered enhancements to exceed sealed IP67 rating
Extended 2 year warranty
NMEA 2000r interface
Type approved as primary heading AND positioning device
Heave, Pitch, Roll and Rate of Turn as standard output
Heading updates 1 to 20 Hz
BAUD Rate selectable: 4800, 9600, 19200, 38400,115200
Fully compatible with on board NMEA 0183 RADAR, ECDIS, AIS, Cameras, SONAR, PC and Autopilots
Compact integrated surface mounting (Pole mount optional)
IMO Compliant, Wheelmark and USCG approved
Pre-programmed default settings for Heading, Rate of Turn, Course over Ground, Lat/Long position, Time & Date
1PPS output standard
15 meter serial cable standard (30 meter optional)
6 meter NMEA 2000® Cable (Optional)
CE certified for EMI and RFI immunity
Worldwide service
|
2792.42 |
|
|
G1 Satellite Compass - NMEA 2000 with 6M Cable
Accurate Heading, Position & Rate of Turn
Features:
Supports both GPS and GLONASS satellites for complete redundancy
Heading accuracy < 0.25° rms
Position accuracy < 0.3m 95% confidence (DGPS)
An integrated 9 Axis Inertial Measurement Core (IMC technology) provides enhanced roll, tilt and heading stability even during momentary loss of satellite signals
G3 color display system (optional)
Engineered enhancements to exceed sealed IP67 rating
Extended 2 year warranty
NMEA 2000® interface
Heave, Pitch, Roll and Rate of Turn as standard output
Heading updates 1 to 20 Hz
BAUD Rate selectable: 4800, 9600, 19200, 38400,115200
Fully compatible with on board NMEA 2000® RADAR, ECDIS, AIS, Cameras, SONAR, PC and Autopilots
Compact integrated surface mounting (Pole mount optional)
IMO Compliant, Wheelmark and USCG approved
Pre-programmed default settings for Heading, Rate of Turn, Course over Ground, Lat/Long position, Time & Date
15 meter serial cable standard (30 meter optional)
6 meter NMEA 2000® Cable (optional)
CE certified for EMI and RFI immunity
Worldwide service
|
2198.23 |
|
|
G2 Satellite Compass - NMEA 2000 with 6M Cable
Accurate Heading & Precise Position for Professionals
Features:
Supports both GPS and GLONASS satellites for complete redundancy
Heading accuracy < 0.25° rms
Position accuracy < 0.3m 95% confidence (DGPS)
An integrated 9 Axis Inertial Measurement Core (IMC technology) provides enhanced roll, tilt and heading stability even during momentary loss of satellite signals
IMO Compliant G3 color display system (optional)
Engineered enhancements to exceed sealed IP67 rating
Extended 2 year warranty
NMEA 2000® interface
Type approved as primary heading AND positioning device
Heave, Pitch, Roll and Rate of Turn as standard output
Heading updates 1 to 20 Hz
BAUD Rate selectable: 4800, 9600, 19200, 38400,115200
Fully compatible with on board NMEA 0183 and NMEA 2000® RADAR, ECDIS, AIS, Cameras, SONAR, PC and Autopilots
Compact integrated surface mounting (Pole mount optional)
IMO Compliant, Wheelmark and USCG approved
Pre-programmed default settings for Heading, Rate of Turn, Course over Ground, Lat/Long position, Time & Date
1PPS output standard
15 meter serial cable standard (30 meter optional)
6 meter NMEA 2000® Cable (Optional)
CE certified for EMI and RFI immunity
Worldwide service
|
2792.42 |
|
|
SC33 Compact Dome Satellite Compass, NMEA2000 (0.4° Heading Accuracy) with 6M Cable
Sleek, Fast & Accurate
The SC33 Satellite Compass provides highly accurate attitude information for navigation equipment such as Radar, Plotter, Autopilot, Fish Finder and Sonar. With its compact GNSS antenna and built-in processor, it can be used for a wide variety of applications on any type of vessel. This all-in-one system delivers incredibly accurate heading and roll & pitch information as well as heaving information, GPS position, SOG (Speed Over Ground), COG (Course Over Ground) and ROT (Rate Of Turn) data.
Employing a two-antenna system with a 3-axis gyro and acceleration sensors, the SC33 enables high-speed response capability. Advanced digital signal processing techniques compute accurate heading based on sensor data. NMEA2000 interface is standard for simple installation, while the optional interface unit IF-NMEASC is available for conventional NMEA0183, AD10 and contact closure.
The GNSS antenna and advanced parallel signal processing allows the SC33 to achieve more precise Pitch, Roll and Heading measurement than conventional models, providing enhanced performance for all of your connected equipment. Its Micro-C pigtail NMEA2000 cable provides flexibility to run cables in challenging areas.
Revolutionary 2-Antenna & Rate Sensor System
In order to calculate roll & pitch data, a satellite compass requires two vectors. The SC33 employs a dual GNSS antenna system that calculates a single vector while a 3-axis rate gyro and acceleration sensors add the 2nd vector. This configuration enables the SC33 to calculate highly accurate roll and pitch data without using a third sensor.
Features:
Highly Accurate Two Antenna Satellite Compass & Rate Sensor System
More resistant to multi-path, shock & vibration, compared to previous models
Improved time to first fix (TTFF) = 60 seconds (typical)
NMEA2000 Certified Interface/NMEA0183 Interface with IF-NMEASC (Optional)
Accuracy: ±0.4° RMS (Heading/Roll/Pitch)
Position Accuracy: 5.0M (GPS); 3.0M (GPS + SBAS)
Integrated Rate Sensors provide Pitch, Roll and Heave Compensation
6 Meter Micro-C Male/Female NMEA2000 Drop Cable (Standard Supply)
Pigtail cable w/NMEA2000 connector for convenient connection to drop cable
Tri-axis speed & direction via PGN 130578 & "Heartbeat" PGN output
SC33 menu access with NavPilot 300 & TZtouch2 (with impending software update)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2869.25 |
|
|
SCX21 Satellite Compass
Utilizing four separate GNSS Antennas for the ultimate in responsiveness, the SCX21 sets a new standard for reliable and accurate heading for all of your marine electronics. The four antennas ensure reliable heading performance, even under the most challenging of conditions. The unprecedented quad antenna design of the SCX21 makes it capable of calculating extremely accurate heading, pitch, roll, and heave information, even when line of sight is limited to only a single satellite. They greatly enhance the performance of onboard equipment such as Radar, Fish Finders, Sonar, and Autopilots.
Features:
Outputs accurate Time, Position, Heading, COG/SOG, ROT (10 degrees/second), Roll/Pitch/Heave 3-Axis Speed, Air Temperature and Air Pressure data
Unprecedented heading accuracy for Radars, Sonars, and Navigation
1.0 degree heading accuracy, 0.02 knot speed accuracy
Extremely compact with easy & flexible installation for reduced susceptibility to multi-path interference
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1674.00 |
|
|
NMEA 0183 Antenna Cable, 7 Pin, 15 Meters
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
136.37 |
|
|
NMEA 0183 Interface Cable
The NMEA 0183 interface provides a bi-directional gateway between an NMEA 2000® network and NMEA 0183 devices.
Ideal for retrofitting NMEA 2000 devices while retaining existing NMEA0183 components, this interface allows boaters a simple way to upgrade to newer technology, sensors, and devices without replacing a whole system. For existing NMEA 2000® networks and systems, this also allows a user to add NMEA 0183 devices to your network, allowing you to choose the products best suited to your boat and sailing.
Simple mounting, connectivity, and a low-profile design allow for easy installation.
Features
Easy to install
Allows older products to connect to new, more modern products
Supports NMEA 0183 Version 4.1
Filter NMEA 0183 rx/tx sentences and configure transmit frequency via Navico®
Compatible with Lowrance®, Simrad®, and B & G® MFDs and instrument displays
NMEA 2000 Compliant
Standard Micro-C connector
|
179.99 |
|
|
NMEA 0183 Threaded Cable Right Angle - 6'
Connect your GPSMAP® device with this 6' (1.8M) threaded NMEA 0183 cable for data communication. The right-angle connector helps with the tight fit often associated with flush mounting.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
29.39 |
|
|
NMEA 0183 Antenna Cable, 7 Pin, 25 Meters
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
174.54 |
|
|
NMEA 0183 10 Meter Connection Cable
A 10 Meter NMEA 0183 connection cable specifically for Maretron's SSC200 & SSC300 Solid State Compasses.
|
62.40 |
|
|
SCX20 Satellite Compass
Utilizing four separate GNSS Antennas for the ultimate in responsiveness, the SCX20 sets a new standard for reliable and accurate heading for all of your marine electronics. The four antennas ensure reliable heading performance, even under the most challenging of conditions. The unprecedented quad antenna design of the SCX20 makes it capable of calculating extremely accurate heading, pitch, roll, and heave information, even when line of sight is limited to only a single satellite. They greatly enhance the performance of onboard equipment such as Radar, Fish Finders, Sonar, and Autopilots.
Features:
Outputs accurate Time, Position, Heading, COG/SOG, ROT (10 degrees/second), Roll/Pitch/Heave 3-Axis Speed, Air Temperature and Air Pressure data
Unprecedented heading accuracy for Radars, Sonars, and Navigation
1.0 degree heading accuracy, 0.02 knot speed accuracy
Extremely compact with easy and flexible installation for reduced susceptibility to multi-path interference
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1674.00 |
|
|
Furuno Leads The Way
To Enhanced Heading Accuracy
With New Satellite Compass Offerings!
In 2001, Furuno introduced ground-breaking new Satellite Compass technology, using GPS satellites to provide a heading fix that rivaled traditional gyrocompass accuracy and repeatability. Since introducing this technology, Furuno satellite compasses have enabled many fleets to eliminate a gyro from their fitting list, saving many thousands of dollars in both equipment cost and wet-sphere gyro maintenance. Continuing our legacy of providing both quality and value, Furuno is very pleased to introduce a new series of Satellite Compasses to replace our revered SC50 and SC110 models.
Furuno's new SC70 (2-antenna) and SC130 (3-antenna) Satellite Compasses offer the stability and reliability of our previous offerings with a few new enhancements. The new SC-series compasses use a color LCD display that fits right in with our overall product family look and feel. In fact, the new SC displays are a cosmetic match with our BR500 BNWAS and FA170 AIS displays, so the vessel dash will look nicely uniform. Even more exciting is our new signal processing, which ensures these compass antennas have greatly reduced susceptibility to multi-path, or "signal bounce", making placement on a vessel mast and installation a breeze. The performance and feature set of the new SC compasses surpass the previous models, with enhanced motion compensation capability and more precise heading, even from the 2-sensor SC70!
Here are some key features and pricing for the SC70 & SC130:
- GPS/WAAS, Galileo and GLONASS position fixing and heading calculation
- Course accuracy 0.25° RMS (SC130), 0.4° RMS (SC70)
- Course and attitude resolution selectable to as fine as 0.001 degrees Rate-of-Turn (ROT) accuracy to .001 degree per second
- Pitch and roll accuracy 0.4° RMS 3
- Axis speed calculation (Bow/Stern/Longitudinal)
- Input/Output:
- NMEA/IEC61162-1/2: 10 Configurable Output & 5 Input Ports
- CAN Bus: 1 port (for connection to NMEA2000 devices)
- AD10: 4 output ports (for connection to legacy equipment)
- IEC61162-450 (Ethernet) network output on RJ45 port for INS and -450 compatible devices
- Type approved as primary or secondary THD (Transmitting Heading Device)* as well as GPS and Rate of Turn Indicator (ROTI)**
*depending on vessel size and Class **ROTI requires use of optional RD50
- 4.3" Color "Wide" WQVGA LCD display
- Single cable connection between antenna and processor (supplied separately)
The SC70 and SC130 models include display, processor, antenna and common installation materials. Antenna cables are a required option and are supplied separately. Please visit the SC70 and SC130 product pages for additional antenna cable options. In addition to the antenna cable, options include LAN cables for connection to Ethernet devices or ship's network. An IF-NMEASC is necessary for analog output or optional IF-2503 for contact closure. Log pulse output is no longer supported.
Specials Closeouts Remanufactured Rebates
|
|
|
Furuno Leads The Way
To Enhanced Heading Accuracy
With New Satellite Compass Offerings!
In 2001, Furuno introduced ground-breaking new Satellite Compass technology, using GPS satellites to provide a heading fix that rivaled traditional gyrocompass accuracy and repeatability. Since introducing this technology, Furuno satellite compasses have enabled many fleets to eliminate a gyro from their fitting list, saving many thousands of dollars in both equipment cost and wet-sphere gyro maintenance. Continuing our legacy of providing both quality and value, Furuno is very pleased to introduce a new series of Satellite Compasses to replace our revered SC50 and SC110 models.
Furuno's new SC70 (2-antenna) and SC130 (3-antenna) Satellite Compasses offer the stability and reliability of our previous offerings with a few new enhancements. The new SC-series compasses use a color LCD display that fits right in with our overall product family look and feel. In fact, the new SC displays are a cosmetic match with our BR500 BNWAS and FA170 AIS displays, so the vessel dash will look nicely uniform. Even more exciting is our new signal processing, which ensures these compass antennas have greatly reduced susceptibility to multi-path, or "signal bounce", making placement on a vessel mast and installation a breeze. The performance and feature set of the new SC compasses surpass the previous models, with enhanced motion compensation capability and more precise heading, even from the 2-sensor SC70!
Here are some key features and pricing for the SC70 & SC130:
- GPS/WAAS, Galileo and GLONASS position fixing and heading calculation
- Course accuracy 0.25° RMS (SC130), 0.4° RMS (SC70)
- Course and attitude resolution selectable to as fine as 0.001 degrees Rate-of-Turn (ROT) accuracy to .001 degree per second
- Pitch and roll accuracy 0.4° RMS 3
- Axis speed calculation (Bow/Stern/Longitudinal)
- Input/Output:
- NMEA/IEC61162-1/2: 10 Configurable Output & 5 Input Ports
- CAN Bus: 1 port (for connection to NMEA2000 devices)
- AD10: 4 output ports (for connection to legacy equipment)
- IEC61162-450 (Ethernet) network output on RJ45 port for INS and -450 compatible devices
- Type approved as primary or secondary THD (Transmitting Heading Device)* as well as GPS and Rate of Turn Indicator (ROTI)**
*depending on vessel size and Class **ROTI requires use of optional RD50
- 4.3" Color "Wide" WQVGA LCD display
- Single cable connection between antenna and processor (supplied separately)
The SC70 and SC130 models include display, processor, antenna and common installation materials. Antenna cables are a required option and are supplied separately. Please visit the SC70 and SC130 product pages for additional antenna cable options. In addition to the antenna cable, options include LAN cables for connection to Ethernet devices or ship's network. An IF-NMEASC is necessary for analog output or optional IF-2503 for contact closure. Log pulse output is no longer supported.
Specials Closeouts Remanufactured Rebates
|
|
|
NMEA 0183 Weather Station Cable - 15M
With NMEA 0183 output only. End in an Airmar 8-Pin connector which can be removed for connection to bare-wire devices.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
141.95 |
|