Hydraulic Ram T2 - 12V B&G's 12V Hydraulic T2 Autopilot Ram

Hydraulic Ram to 12V High power, efficient drive units for maximum power with minimum consumption. Ram drives allow the Power Steer mode on the Pilot to be used in cases of manual steering failure Fully Integrated (T0, T1 and T2 units) hydraulic system, no external hoses, reservoirs etc. Always remember to use the fully laden displacement of your boat when selecting a pilot. Typically a yacht fully provisioned with the water and fuel tanks full can be as much as 20% above the designed displacement. If your boat falls between two pilot types, choose the larger pilot type - an under rated pilot may not be able to perform adequately when you need it most. If in doubt, please check with an authorized B & G Dealer. If you are using a Ram, Rotary drive or existing drive unit from another manufacturer, these will, in most cases, be compatible with B & G units. Features: Max Boat Size: 19,000 lbs (9000 kg) Stroke: 7.87 in (200 mm) Hard Over Time: 12 sec Tiller Arm: 6.89 in (175 mm) Thrust: 771.6 lbs (350 mm) Rudder Torque: 136.6 lbs (62 kg) Required Computer: AC12, NAC-2 *Typical average cruising consumption

Hydraulic Ram Type 1 - 12V High power, efficient drive units for maximum power with minimum consumption Ram allows the Power Steer Mode on the Pilot to be used in case of manual steering failure Integrated hydraulic system: no external hoses, reservoirs, etc...

Hydraulic Gear Pump - 12V - 20-30CI Cylinder - 2000cc/min Gear Pump Offers Industry Leading Reliability and Performance in a Smaller, Lighter, Quieter Package. Features: High Efficiency – Industry leading efficiency minimizes power consumption Low Noise – New industry design offers significantly quieter operation Light Weight & Compact – Small footprint offers greater installation flexibility Wide Range Of Products – From 600 to 1600cc/min, 12v and 24v options Professional Solutions for Hydraulically Steered Boats: Industry Leading Efficiency – lower power consumption, particularly under demanding conditions requiring higher flow rates equates to a major advantage over competing units. Cost Savings – the increased efficiency and performance means the pumps can be used with smaller autopilot course computers than equivalent drive units. The smaller footprint of the compact gear pump increases installation flexibility. Lower noise and vibration make the gear pump particularly suitable for sailboat installations. Suitable for balanced or unbalanced cylinders. All models available for both 12v and 24v systems.

Hydraulic Gear Pump - 12V - 30-40CI Cylinder Gear Pump Offers Industry-Leading Reliability and Performance in a Smaller, Lighter, Quieter Package. Features: High Efficiency – Industry-leading efficiency minimizes power consumption Low Noise – New industry design offers significantly quieter operation Light Weight & Compact – Small footprint offers greater installation flexibility Wide Range Of Products – From 600 to 1600cc/min, 12v and 24v options Professional Solutions for Hydraulically Steered Boats: Industry-Leading Efficiency – lower power consumption, particularly under demanding conditions requiring higher flow rates equates to a major advantage over competing units. Cost Savings – the increased efficiency and performance means the pumps can be used with smaller autopilot course computers than equivalent drive units. The smaller footprint of the compact gear pump increases installation flexibility. Lower noise and vibration make the gear pump particularly suitable for sailboat installations. Suitable for balanced or unbalanced cylinders. All models are available for both 12v and 24v systems.

Hydraulic Power Unit 12V with Deutch Connector A compact powerhouse that creates hydraulic pressure to lower and raise the trim tabs. It employs two solenoid valves to direct the flow of fluid to the actuators. The solenoid valves lock tightly to secure the tabs in place. Strength to lower and hold even the largest tabs in place. The Lexan cover provides water resistance to the electrohydraulic unit, and the translucent reservoir allows fluid check at a glance. The mounting bracket is sold separately (# H1179). HPU measures 4″ x 7 1/2″ x 5 1/2″. Uses automatic transmission fluid. Includes pump, solenoid valves, reservoir, and cover.  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Hydraulic Gear Pump 12V 6-9CI Cylinder From the design team that brought you the legendary Octopus hydraulic drives, our new gear pump offers industry leading reliability and performance in a smaller, lighter, quieter package. Features: Industry leading efficiency - lower power consumption, particularly under demanding conditions requiring higher flow rates equates to a major advantage over competing units. Cost saving - the increased efficiency and performance means the pumps can be used with smaller autopilot course computers than equivalent drive units. The smaller footprint of the compact gear pump increases installation flexibility. Lower noise and vibration make the gear pump particularly suitable for sailboat installations. Suitable for balanced or unbalanced cylinders. All models available for both 12v and 24v systems. Specifications: Flow Rate: 600CC/min Voltage: 12 Volt Cylinder Range: 6-9ci CYLINDER Average Current Draw: 3.8A Operating Temperature: -15 to +75'C (5 - 167'F) Waterproofing: IP55 Ignition Protection: ISO 8846 & SAEJ1171 EMC Compliance: EN60945-9-2002

Hydraulic Gear Pump 12V 10-15CI Cylinder From the design team that brought you the legendary Octopus hydraulic drives, our new gear pump offers industry leading reliability and performance in a smaller, lighter, quieter package. Features: Industry leading efficiency - lower power consumption, particularly under demanding conditions requiring higher flow rates equates to a major advantage over competing units. Cost saving - the increased efficiency and performance means the pumps can be used with smaller autopilot course computers than equivalent drive units. The smaller footprint of the compact gear pump increases installation flexibility. Lower noise and vibration make the gear pump particularly suitable for sailboat installations. Suitable for balanced or unbalanced cylinders. All models available for both 12v and 24v systems. Specifications: Flow Rate: 1000CC/min Voltage: 12 Volt Cylinder Range: 10-15ci CYLINDER Average Current Draw: 5A Operating Temperature: -15 to +75'C (5 - 167'F) Waterproofing: IP55 Ignition Protection: ISO 8846 & SAEJ1171 EMC Compliance: EN60945-9-2002

Hydraulic Gear Pump 12V 16-24CI Cylinder From the design team that brought you the legendary Octopus hydraulic drives, our new gear pump offers industry leading reliability and performance in a smaller, lighter, quieter package. Features: Industry leading efficiency - lower power consumption, particularly under demanding conditions requiring higher flow rates equates to a major advantage over competing units. Cost saving - the increased efficiency and performance means the pumps can be used with smaller autopilot course computers than equivalent drive units. The smaller footprint of the compact gear pump increases installation flexibility. Lower noise and vibration make the gear pump particularly suitable for sailboat installations. Suitable for balanced or unbalanced cylinders. All models available for both 12v and 24v systems. Specifications: Flow Rate: 1600CC/min Voltage: 12 Volt Cylinder Range: 16-24ci CYLINDER Average Current Draw: 6.6A Operating Temperature: -15 to +75'C (5 - 167'F) Waterproofing: IP55 Ignition Protection: ISO 8846 & SAEJ1171 EMC Compliance: EN60945-9-2002

Type 3 Hydraulic Linear - 12V  Type 3 Hydraulic Linear system for mechanically steered vessels up to 77,000lb (35,000kg) displacement. The hydraulic linear drive system is designed for boats with existing mechanical steering systems, not hydraulic steering systems. It provides a totally isolated autopilot steering system consisting of: Features: Hydraulic ram: a self-contained autopilot steering cylinder with a load limiting system and a built in clutch (to allow friction-free steering when the autopilot is not in use) Reversing hydraulic pump: powers the hydraulic ram Hydraulic fluid reservoir: supplies hydraulic fluid to the system

Hydraulic Linear Drive Type 3 - 24V The hydraulic linear drive system is designed for boats with existing mechanical steering systems, not hydraulic steering systems. It provides a totally isolated autopilot steering system consisting of: Hydraulic ram: a self-contained autopilot steeringcylinder with a load limiting system and a built in clutch (to allow friction-free steering when the autopilot is not in use). Reversing hydraulic pump: powers the hydraulic ram. Hydraulic fluid reservoir: supplies hydraulic fluid to the system.

RAM 11mm Flat Base with Double Socket Arm and Diamond Adaptor (U) The RAM-B-179U, offset motorcycle base, makes attaching to a variety of mounting locations, including handlebars, a breeze. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your mobile electronic device is safe, secure, and within easy reach. RAM's patented design also dampens shock and vibration helping to extend the life of your mobile device. With a turn of a single comfortable to grasp knob, adjustments can be made and the sleek hourglass shape of the arm assembly compliments the lines of any motorcycle. The RAM-B-252U, base for the RAM-B-179U, consists of a 1" diameter ball and 2.25" x 0.875 base with 11mm hole. This part is often used on motorcycles, attaching to the mirror frame, the main brand of bike for the RAM-B-252U is BMW. This part fits well on many handlebar pinchbolts with a washer (base is 5mm thick). Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM 9mm Angled Base with Double Socket Arm and Diamond Adaptor (U) The RAM-B-180U, offset motorcycle base, makes attaching to a variety of mounting locations, including handlebars, a breeze. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your mobile electronic device is safe, secure, and within easy reach. RAM's patented design also dampens shock and vibration helping to extend the life of your mobile device. With a turn of a single comfortable to grasp knob, adjustments can be made and the sleek hourglass shape of the arm assembly compliments the lines of any motorcycle. The RAM-B-272U, base for the RAM-B-180U, consists of a 1" diameter ball and base with 9mm hole. This part is often used on motorcycles, attaching to the mirror frame, the main brand of bike for the RAM-B-272U is BMW. Material: Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

Pump-4 MK2 Reversible Hydraulic Pump for SteadySteer Features: 12V DC: Reversible hydraulic gear pump. 3.0L (183 cui) / min For cylinder displacement of 290 - 960 cc (17.7 - 58.5 cu. in.) O-Ring Boss (ORB) connections. Includes 3 x ORB-5 to 9/16 UNF fittings SteadySteer compatible. (NAC-3 / AC42 required).

RAM® Track Ball™ Mount for Garmin Striker + More This RAM® Track Ball™ bundle includes the RAM® Track Ball™, the RAM® Double Socket B Size Arm, and the RAM® Round Plate with Ball & Mounting Hardware for Garmin Striker and other fishfinder models. The RAM® Track Ball™ consists of a B-size 1" rubber ball molded to a high-strength composite base, a rubber friction washer, and a stainless steel T-bolt for sliding into virtually any track system. Simply insert or slide the RAM® Track Ball™ into the track and twist the ball clockwise to tighten it in place. Twist counterclockwise to loosen or adjust the ball. The included RAM-B-201U consists of a medium-length double socket arm that accommodates 1" B-size ball bases, device holders, and adapters. The easy-to-adjust knob allows for near-infinite adjustability for the connected device. The RAM-B-202-G4U consists of a 1"-diameter rubber ball connected to a flat 2.5"-diameter base. This mount has pre-drilled holes, including the universal AMPS hole pattern. Included are 3x (#8-32 x 5/8” PH PD Mach Screws) and 3x (#8-32 SS Nylock Nuts) that will connect the RAM-202-G4U to the bottom of the Garmin echo™ and Striker™ 4 Series. Features: Designed for track mounting systems including the RAM® Tough-Track™; includes 1" B-size rubber ball Features a rubber friction washer and a stainless steel T-bolt; simply insert it into the track and twist the ball clockwise to tighten Standard RAM® double socket arm provides an ideal overall length of 3.73" and a socket-to-socket length of 3" Made of high-strength composite and steel components for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: (3) #8-32 x 5/8" Machine Screws and (3) #8-32 Nylock Nuts T-Bolt Dimensions (inch): 0.48" x 0.95" Socket to Socket Length: 3" Hole Pattern (inch): 4-Hole AMPS: 1.181" x 1.496"; 3-Hole 120-Degree: 1.812" Diameter Ball Size: B Size (1") Weight Capacity: Standard Use: 2 lbs, Heavy-Duty Use: 1 lb Materials: Marine-grade aluminum and high-strength composite Packaging Type: Polybag Weight: 0.4 lbs. Compatibility: Garmin: Striker 4, Striker 4dv, Striker Plus 4cv, Striker Vivid 4cv, echo 100, echo 150, echo 300c, ECHOMAP Plus 42cv, ECHOMAP Plus 43cv, ECHOMAP Plus 44cv, ECHOMAP Plus 45cv, and ECHOMAP UHD2 6"