|
Panel-Mounted Battery Mini Selector Switch
Panel-mounted switches are designed specifically for panel mount applications. This range gives a very compact, versatile solution.
Compact, lightweight
Countersunk recesses for surface mount application
Standard 2-1/16" (52 mm) hole cut out (same as standard gauge hole)
Inside: captive inserts for 3/16" (4.8 mm) nuts providing full access for cables with no restrictions
Standard interchange label system
Molded in high temperature, fiber reinforced plastics
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
36.89 |
|
|
Panel-Mounted Battery Master Switch
Panel-mounted switches are designed specifically for panel mount applications. This range gives a very compact, versatile solution.
Compact, lightweight
Removable key
Countersunk recesses for surface mount application
Standard 2-1/16" (52 mm) hole cut out (same as standard gauge hole)
Inside: captive inserts for 3/16" (4.8 mm) nuts providing full access for cables with no restrictions
Standard interchange label system
Molded in high temperature, fiber reinforced plastics
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
24.07 |
|
|
Panel Mounted DC Systems Monitor
The Contour Digital Monitor offers a comprehensive range of functions to allow full monitoring of your batteries and charging systems. Monitors voltage on up to 3 battery banks, Amps for charge and discharge and capacity remaining in amp hours /percentage utilising peukerts exponent (house bank only) with the added function of a bilge monitor allowing 24 hour monitoring of your bilge pump. This meter is an important addition to modern battery management systems. Selectable legends allow full information to be shown on the screen to avoid confusion, unlike other digital meters available, which only show confusing digits. LCD screen draws 70 percent less than equivalent LED screens. Comes supplied with shunt, part No. LB-450-50. Installation kits are available in 5m and 10m lengths.
|
459.88 |
|
|
Ultra Safety Systems Ultimate Mini Bilge Switch 12V
ULTRA PUMP SWITCH MINI
4 inch high, 1 3/4 inch diameter, 3/4 inch ON/OFF differential
12 Volts/40 Amp relay
20 Amp continues pump load
With Magnetic Test Switch
5 year warranty
|
204.75 |
|
|
Ultra Safety Systems Ultimate Mini Bilge Switch 24/32V
ULTRA PUMPSWITCH MINI
4 inch high, 1 3/4 inch diameter, 3/4 inch ON/OFF differential.
24/32 Volts. 40 Amp relay
20 Amp continuous pump load
With Magnetic Test Switch.
5 year warranty
|
195.00 |
|
|
7042 187-Series Circuit Breaker - Panel Mount 80A
Features:
Combines switching and circuit protection into a single device*
Precise, single-lever operation
"Trip Free" design cannot be held "ON" during fault current condition
Waterproof
Recessed mounting holes for clean appearance
Ample Clearance around terminal studs accepts heavy gauge wire lugs
Robust 5/16 M8 terminals provide high torque connections
Large lever with vertical/horizontal orientation provides indication of trip status
Ignition-protected - Safe for installation aboard gasoline powered boats
Specifications:
Amperage: 80A
Maximum Voltage: 48V DC
Mounting: Panel Mount
Circuit Breaker Type: Thermally responsive Bi-metal blade
Terminal Stud Torque: 75 in-lb (8.47 Nm)
Interrupt Capacity: 5000A @ 14VDC, 3000A @ 28VDC, 1500A @ 48VDC
Minimum Operating Temperature: -40° C
Maximum Operating Temperature: 85° C
Case Material: Thermoset Polyester
Circuit Breaker Class: Type III - switchable/manual reset - trip-free
Mounting Hole: Accept #10 (M5) Screw
Terminal Stud Size: 5/16" - 18
Weight: 0.5lb (0.23 kg)
Weight: 0.50lb (0.23 kg)
* Do not use as a switch where high inrush currents are expected.
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
70.93 |
|
|
Micropump DG-F61.G1R2P5.J.B I Drive Motor J Mount
Replacement for Micropump I-Drive IEG
J-mount, Speed Control(0-5VDC)
Micropump I-Drive IEG, 0-5 VDC SPEED CONTROL INPUT; J-Mount
|
1649.51 |
|
|
Micropump DG-F61.G1S2P5.J.B I Drive Motor J Mount
Micropump Brushless DC I-Drive
|
1869.44 |
|
|
Mini Battery Selector Switch
The 701S is the most compact selector switch available on the market. While BEP recommends isolated battery systems as outlined with our distribution clusters, the 701S provides a simple economical way of separating two batteries. BEP Marine Battery Switch Test Procedures (UL 1107) Continuous (1 hour), intermittent (5 minutes) and Cranking (engine starting - 10 seconds). The test is to determine the maximum current the switch can handle for the stated time, without the rear terminals exceeding 100 deg C (212 deg F) above the ambient temperature. The continuous and intermittent ratings are tested at 110% of specified ratings. All BEP switches are tested Independently to this specification by a 3rd party laboratory.
Housed in the same dimensions as the 701, and includes the same removable side plates and back cover
Please note selector switches will not separate electronics from harmful engine starting spikes
Tin-plated copper studs and nuts
Ignition-protected
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
35.83 |
|
|
Heavy-Duty Battery Selector Switch
The 721 Battery Selector Switch is our heavy duty selector switch. Housed in the same module as the 720, it includes the same removable plates and back cover. While BEP Marine recommends isolated battery systems as outlined with our distribution clusters, the 721 offers a simple economical way of separating two batteries. Please note selector switches will not separate electronics from harmful engine starting spikes.
Specifications:
DC Voltage: 48
Stud Size (Imperial): 3 x 3/8"
Stud Size (Metric): 2 x 10mm
Continuous Rating: 350
Intermittent Rating: 500
Cranking Rating: 1500
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
59.10 |
|
|
Medium Duty Battery Selector Switch w/Key Lock
Perko's 8501 Series battery selector switches are among the most popular battery switches ever produced. Their use of the traditional Perko bolt circle makes for easy installation, whether new or as a replacement. These switches can be mounted in numerous locations. And as ignition protected switches, they can be installed in the engine rooms of gasoline powered boats.
In addition to doing everything a battery disconnect switch does, battery selector switches permit battery selection (of two or more batteries) for specific purposes including starting engines, running accessories or even recharging. They allow for the use of one or more batteries in systems with one or more engines and facilitate putting batteries in parallel for emergency starting when one or both batteries are substantially discharged.
Perko battery switches are designed for surface mounting. Standard duty switches have a bright red polycarbonate housing for safety with a large easy-to-turn black knob. The housing of the heavy duty switches are red fiber-reinforced polycarbonate. Selector switches are designed with a "make before break" feature. This allows switching between the "1", the "ALL" and the "2" positions while the engine is running. Models with an "Alternator Field Disconnect" feature offer protection for Non-Unitized Alternators should the switch accidentally be turned to the "OFF" position with the engine running.
Versions of the 8501 Series switches offer additional features such as alternator disconnect and key lock security.
The 90° rotation feature allows users to feel the switches' position in no light situations and the classic shape of the knob makes it easy to turn.
High conductivity studs are long enough to handle more than 1 cable and strong enough for torque needed for secure connections. Optional spacer ring (PN 0462DP0RED) allows for the use of larger cables.
Specifications:
Diameter: 5-1/4"
Depth: 2-5/8"
For use with 6 to 50 Volt Marine Electrical Systems
Capacity - 250 AMPS Continuous, 360 AMPS Intermittent
When used with Non-Unitized Alternators, these models will interrupt the field current (reducing the possibility of damage) if turned "OFF" with the engine running
|
73.54 |
|
|
Pro Installer 400A EZ-Mount Battery Selector Switch (1-2-Both-Off)
As easy as 1, 2, 3, these revolutionary battery switches allow you to wire from the front. Never has installation been so easy and cabling so accessible. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze. Pro Installer switches set the new benchmark with outstanding ergonomics, intuitive look/feel, and are engineered from the finest materials to withstand the harsh marine environment. The outstanding performance and features of this powerful new generation battery switch appeal to both the installer and end user. All ratings, footprints and features of the EZ-Mount switch match the high quality of our standard switches.
Tested to UL1107 ignition protection, CE
Tinned copper 10mm (3/8") studs
Stainless steel washers/nuts
Fiber reinforced plastics
400A Continuous / 600A 5 mins Intermittent / 1500A 10 secs Cranking
Waterproof to IP66
Same interconnection height as Pro Installer
Removable knob allows isolation during servicing
3 removable sideplates for protection
Industry standard 3.85" x 3.85" footprint
Specifications
Mounting: Surface Only
Voltage: 48v DC (for 12-48v systems)
Rating: 400 Cont / 600 Inter / 1500 Crank
Dims: 3.85" x 3.85" x 3.62"
Operation: 1-2-Both-Off
Stud: 3x 10 mm (3.8")
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
58.00 |
|
|
Contour Connect 3 Hole Module Body
The CC-5 module will house the following components.
701-PM Panel mount battery switch
701S-PM Panel mount battery selector switch
184 and 185 series Bussman circuit breakers (CC-HDBM must be ordered also)
710-125A Voltage Sensitive Relay
710-125A-DS Voltage Sensitive Relay dual sense
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
40.55 |
|
|
Compact Battery Selector & Main Disconnect Switches
Ignition Protected
For use with 12, 24 and 32 volt marine electrical systems
Higher Rating Than Popular 8500 Series Switches
Same bolt patterns as popular 8500 series
Smooth, positive position selector
Compact, Medium Duty Battery Selector Switch
|
62.24 |
|
|
Compact Battery Selector & Main Disconnect Switches
Ignition Protected
For use with 12, 24 and 32 volt marine electrical systems
Higher Rating Than Popular 8500 Series Switches
Same bolt patterns as popular 8500 series
Smooth, positive position selector
Compact, Medium Duty Battery Selector Switch w/ Key Lock
|
73.54 |
|