|
Replacement Outboard Tilt Trim Motor & Reservoir Only - Mercury/Mariner & Force Motor
Replacement outboard tilt trim motor and reservoir that will fit late model Mercury /Mariner, Force 40-125 HP outboards w/single ram, 2-wire connection, 4-bolt mount, Hollow-hex shaft, (Motor/Reservoir Only) Includes stainless steel mounting screws, shaft adaptor, O-ring and fill plug. Bullet Connector Terminal Ends.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
MERCURY Tilt Trim Motor 19217A1
MERCURY Tilt Trim Motor 19217A5
MERCURY Tilt Trim Motor 809885A1
MERCURY Tilt Trim Motor 809885A2
MERCURY Tilt Trim Motor 809885T2
MERCURY Tilt Trim Motor 811674
MERCURY Tilt Trim Motor 813447
MERCURY Tilt Trim Motor 818903A1
MERCURY Tilt Trim Motor 819479A1
MERCURY Tilt Trim Motor 8197480A1
MERCURY Tilt Trim Motor 819762A4
MERCURY Tilt Trim Motor 19762A5
MERCURY Tilt Trim Motor 19762A6
MERCURY Tilt Trim Motor 19762A7
MERCURY Tilt Trim Motor 1977A8
MERCURY Tilt Trim Motor 1977A9
MERCURY Tilt Trim Motor 22870A1
MERCURY Tilt Trim Motor 30250A3
MERCURY Tilt Trim Motor 30250T3
MERCURY Tilt Trim Motor 2021A1
MERCURY Tilt Trim Motor 32021T1
MERCURY Tilt Trim Motor 32021A2
MERCURY Tilt Trim Motor 32021T2
MERCURY Tilt Trim Motor 55654A1
MERCURY Tilt Trim Motor 55654T2
MERCURY Tilt Trim Motor 893907A02
SIERRA Tilt Trim Motor 18-6777
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
353.87 |
|
|
Airmar DT812BV-235-N2 235 kHz Low Profile Tilted Element™ Smart™ Sensor 12° Tilt Bronze NMEA 2000
Airmar has taken its proven Tilted Element™ and broadband technologies and applied them to its leading line of Smart™ Sensors. The DT800 is a low-profile, retractable, thru-hull sensor that computes accurate depth and temperature data and sends it to any NMEA 0183 or NMEA 2000® display. The DT800 operates at a frequency of 235 kHz and can run simultaneously with other Airmar 50/200 kHz transducers on-board with no interference. The broadband ceramic delivers depth readings to 183M (600'), as well as accurate shallow-water readings in as little as 500 mm (1.6').
Airmar's Smart™ Sensors have embedded microelectronics - the transducer element and signal processor are only millimeters apart. The signal from the depth transducer is processed right inside the sensor itself. All that is needed to receive depth and temperature data is a single cable into a compatible device or display. Because the ceramic is tilted inside the housing, the transducer beam is oriented straight down, resulting in strong bottom echo returns and accurate depth readings. The retractable housing with a self-closing valve reduces water flow into the vessel when the transducer is removed for cleaning.
Smart™ Sensor Features
Enhanced depth performance
Maximum Depth Range: 180M (594')
Minimum range 0.5M (1.6')
Urethane face provides better sensitivity
Excellent high-speed performance
Fixed 20° tilt for 16° to 24° deadrise
Fixed 12° tilt for 8° to 15° deadrise
Fixed 0° tilt for 0° to 8° deadrise
NMEA 2000 output
100 W RMS power
Frequency: 235 kHz
Cone: 12°
All models have depth and temperature
235 kHz eliminates interference with fishfinders
Retractable insert provides ease of serviceability
Usable Shaft Length: 57mm (2.25")
.6M(19.8') NMEA 2000® devicenet cable and connector
51mm (2") housing
Blanking plug included
Accommodates maximum hull thicknesses 54mm (2-1/8")
Accommodates minimum hull thicknesses 6.3mm (0.25")
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
449.96 |
|
|
Airmar DT820BV-235-N2 235 kHz Low Profile Tilted Element™ Smart™ Sensor 20° Tilt Bronze NMEA 2000
Airmar has taken its proven Tilted Element™ and broadband technologies and applied them to its leading line of Smart™ Sensors. The DT800 is a low-profile, retractable, thru-hull sensor that computes accurate depth and temperature data and sends it to any NMEA 0183 or NMEA 2000® display. The DT800 operates at a frequency of 235 kHz and can run simultaneously with other Airmar 50/200 kHz transducers on-board with no interference. The broadband ceramic delivers depth readings to 183M (600'), as well as accurate shallow-water readings in as little as 500 mm (1.6').
Airmar's Smart™ Sensors have embedded microelectronics - the transducer element and signal processor are only millimeters apart. The signal from the depth transducer is processed right inside the sensor itself. All that is needed to receive depth and temperature data is a single cable into a compatible device or display. Because the ceramic is tilted inside the housing, the transducer beam is oriented straight down, resulting in strong bottom echo returns and accurate depth readings. The retractable housing with a self-closing valve reduces water flow into the vessel when the transducer is removed for cleaning.
Smart™ Sensor Features
Enhanced depth performance
Maximum Depth Range: 180M (594')
Minimum range 0.5M (1.6')
Urethane face provides better sensitivity
Excellent high-speed performance
Fixed 20° tilt for 16° to 24° deadrise
Fixed 12° tilt for 8° to 15° deadrise
Fixed 0° tilt for 0° to 8° deadrise
NMEA 2000 output
100 W RMS power
Frequency: 235 kHz
Cone: 12°
All models have depth and temperature
235 kHz eliminates interference with fishfinders
Retractable insert provides ease of serviceability
Usable Shaft Length: 57mm (2.25")
.6M(19.8') NMEA 2000® devicenet cable and connector
51mm (2") housing
Blanking plug included
Accommodates maximum hull thicknesses 54mm (2-1/8")
Accommodates minimum hull thicknesses 6.3mm (0.25")
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
449.96 |
|
|
Premium Replacement Tilt Trim Sender for Mercury
This tilt trim sender fits MC-I, R, MR, Alpha, Alpha Gen II, and Bravo drives.
Replaces:
MERCURY Tilt Trim Sender 805320A03
MERCURY Tilt Trim Sender 805320A1
MERCURY Tilt Trim Sender 17693A2
MERCURY Tilt Trim Sender 96863A15
MERCURY Tilt Trim Sender 63115A12
MERCURY Tilt Trim Sender 88678A4
MERCURY Tilt Trim Sender 88678A5
SIERRA Tilt Trim Sender 18-7633
*ARCO Assurance 12-month part and labor warranty protection
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
59.99 |
|
|
DT812PV-235-N2 - 235kHz - Plastic Thru Hull Smart Sensor - 12° Tilt - NMEA 2000 - 6M Cable
Airmar has taken its proven Tilted Element™ and broadband technologies and applied them to its leading line of Smart™ Sensors. The DT800 is a low-profile, retractable, thru-hull sensor that computes accurate depth and temperature data and sends it to any NMEA 0183 or NMEA 2000® display. The DT800 operates at a frequency of 235 kHz and can run simultaneously with other Airmar 50/200 kHz transducers on-board with no interference. The broadband ceramic delivers depth readings to 183 m (600'), as well as accurate shallow-water readings in as little as 500 mm (1.6'). Available in fixed 0°, 12°, or 20° tilt, the DT800 is perfect for power and sailboat applications. It is sold with a choice of rugged housings— plastic, bronze, or stainless steel—to accommodate any vessel type or hull material. These low-profile housings do not affect hull performance and will provide accurate readings at high speeds.
Airmar's Smart™ Sensors have embedded microelectronics—the transducer element and signal processor are only millimeters apart. The signal from the depth transducer is processed right inside the sensor itself. All that is needed to receive depth and temperature data is a single cable into a compatible device or display. Because the ceramic is tilted inside the housing, the transducer beam is oriented straight down, resulting in strong bottom echo returns and accurate depth readings. The retractable housing with a self-closing valve reduces water flow into the vessel when the transducer is removed for cleaning.
Smart™ Sensor Features
Broadband ceramic available with 0°, 12° and 20° tilt options
Enhanced depth performance
Maximum Depth Range: 180M (594’)
Minimum range 0.5M (1.6’)
Urethane face provides better sensitivity
Excellent high-speed performance
Fixed 12° tilt for 8° to 15° deadrise
NMEA 2000 output
100 W RMS power
Frequency: 235 kHz
Cone: 12°
All models have depth and temperature
235 kHz eliminates interference with fishfinders
Retractable insert provides ease of serviceability
Usable Shaft Length: 57mm (2.25”)
6M(19.8”) NMEA 2000® devicenet cable and connector
51mm (2”) housing
Blanking plug included
Accommodates maximum hull thicknesses 54 mm (2 1/8”)
Accommodates minimum hull thicknesses 6.3 mm (0.25”)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
341.88 |
|
|
DT800 NMEA 2000 Thru-Hull Tilted Element Smart Sensor - 20°
Function: Depth / Temperature, Material: Plastic, Fixed Tilt Angle: 20°
Frequency: 235 kHz, Cone: 12°, Power: 100 Watts RMS
Connector: 5-Pin NMEA 2000
Features:
Low-profile, retractable, thru-hull transducer offers depth and temperature functions in a single, compact housing
Tilted Element Transducer – unique design tilts ceramic element inside transducer housing, giving all the advantages of a fairing block without a hull protrusion
Available in fixed 0°, 12° or 20° tilt – perfect for power and sail boat applications
Low-profile housing compensates for hull deadrise, does not affect hull performance and provides accurate readings at high speeds
Designed with Airmar's exclusive Broadband Ceramic Technology, 235 kHz element improves resolution without sacrificing sensitivity
Smart™ Sensor with embedded microelectronics – transducer element and signal processor are only millimeters apart
235 kHz frequency prevents mutual interference with other echo sounders on vessel
Retractable housing with self-closing valve minimizes water flow into the vessel when transducer is removed for servicing
Specifications:
Mount: Thru-hull
Fixed Element Tilt Angle: 20° (for 16° - 24° hull deadrise)
Housing Material: Plastic
Connector: 5-pin NMEA 2000®
Cable Length: 20 ft.
Frequency: 235 kHz
Cone: 12°
Power: 100 Watts RMS
Depth Sensor Range: 1.6 - 594 ft.
Acoustic Window Material: Urethane
Compatible Hull Materials: Fiberglass or metal
Hole Diameter for Installation: 2"
Dimensions: 4.92" H x 2.94" OD
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
341.88 |
|
|
B-60-12 Tilted Element Transducer
Low profile tilted element for 8° to 15° deadrise hulls.
Features:
600 Watts
Dual 50/200kHz
|
378.00 |
|
|
Replacement Outboard Tilt Trim Motor - Honda/Suzuki - 4 Bolt Mount
Quality Assurance:
Epoxy Powder coated for maximum corrosion protection
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Precision Testing:
All armatures tested to withstand 50 times operation voltage (12V)
All motors performance tested at 5 different load levels
All motors must meet or exceed OEM performance before being boxed
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Fits:
HONDA 2002-Up BF175, BF200, BF225, 4-bolt mount, Round Plug-In Connector. Includes O-ring.
SUZUKI 2002 and up 175, 200 & 225hp 4 Stroke
Replaces Part Numbers:
HONDA Tilt Trim Motor 36120-ZY3-013
SUZUKI Tilt Trim Motor DF140TLK2
SUZUKI Tilt Trim Motor DF140TXK2
SUZUKI Tilt Trim Motor DF140TXZK2
SUZUKI Tilt Trim Motor DT150TCXK2
SUZUKI Tilt Trim Motor DT225TCXGK2
SUZUKI Tilt Trim Motor DT225TCXK2
SIERRA Tilt Trim Motor 18-6742
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
329.96 |
|
|
Original Equipment Quality Replacement Tilt Trim Motor for Mercruiser I/O & Mercury O/B with Oildyne Pump
Replacement tilt trim motor that will fit Mercruiser I/O and Mercury Outboards with Oildyne pump. 12 Volt, Ring Terminal Ends
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
MERCURY Tilt Trim Motor 17649
MERCURY Tilt Trim Motor 17649A1
MERCURY Tilt Trim Motor 17649A02
MERCURY Tilt Trim Motor 17649T
MERCURY Tilt Trim Motor 87828
MERCURY Tilt Trim Motor 891736T
SIERRA Tilt Trim Motor 18-6772
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
164.72 |
|
|
Replacement Outboard Tilt Trim Motor - Late Model Mercury, 2-Wire
Replacement outboard tilt trim motor that will fit late model Mercury 135, 150 XR6, Magnum lll, 175, 200, 225, 250 HP, 105-140 HP Jet, 2-wire connection, 2-bolt mount, Includes O-ring, Flat-blade shaft, Bullet Connector Terminal Ends.
ARCO advises cleaning all connections: A corroded connection creates resistance, lowering the amperage required to operate the motor.
Features:
Tilt trim motors are dynamically tested to ensure out-of-the-box performance
Motor shafts induction case hardened at bearing surfaces for superior wear resistance
Epoxy Powder coated for maximum insulation protection
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for a period of 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
MERCURY Tilt Trim Motor 8M0031551
MERCURY Tilt Trim Motor 8M0060140
MERCURY Tilt Trim Motor 828708
MERCURY Tilt Trim Motor 828708T
MERCURY Tilt Trim Motor 878265A1
MERCURY Tilt Trim Motor 878265A4
SIERRA Tilt Trim Motor 18-6773
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
238.67 |
|
|
B164 Tilted Element™ 10 Pin
12°
Features:
Depth/Temp
50/200 kHz
1 kW RMS
High-performance
Bronze
Step up to a 1kWWithout a Fairing! Airmar has taken our innovative Tilted Element™ technology to a higher power. The new 1kW, flush-mount, tilted element transducers are perfect for fast, trailered tournament sport fishing vessels who cannot have a high-performance fairing. The flush mounted, bronze housing protrudes less than 6.35 mm (0.25) outside your hull and can sit on trailer rollers and bunks with no damage at all. The ceramic arrays are tilted inside the housing giving you the perfect vertical beam with maximum energy on what is directly below your boat. Take your fishfinder to the next power with Airmars 1kW tilted element transducers.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
1061.33 |
|
|
B-60-20 Tilted Element Transducer
Low profile tilted element for 16° to 20° deadrise hulls.
Features:
600 Watts
Dual 50/200kHz
|
378.00 |
|
|
DST810 Smart™ Multisensor 23kHz Bronze NMEA 2000® Transducer - N2K
Depth, Speed-Through-Water, Water Temperature, Boat Attitude! The DST810 Smart Multisensor, featuring the new Gen2 paddlewheel and AIRMAR's CAST™ app, delivers a powerful combination of best-in-class speed performance and a simple, reliable way to calibrate accurate speed using your wireless device. The Gen2 paddlewheel delivers industry-leading start-up speed-through-water data below 0.3 knots and is linear at 0.6 knots, maintaining accurate performance up to 45 knots.
The DST810 and CAST app provides a simple, consistent way to calibrate speed through the water. The free CAST app delivers calibration options that, until now, were only available through expensive PC-based software. In addition to water temperature, depth, and upgraded 5.7 Hz (5X per second) speed-through-water output with improved speed resolution, the DST810 features an integrated attitude sensor for heel and trim data. This information, combined with Airmar’s powerful and simple CAST app, makes heel-compensated speed calibration across multiple heel angles and speed ranges fast and intuitive, and is independent of the onboard instruments.
Features:
Smoother Speed – 5.7 Hz speed output (5X per second) for visibly smoother speed-through-water reporting and faster data for better decision-making when every second counts.
Integrated Attitude Sensor – for heel and trim and used in advanced speed calibration.
Wireless connectivity to AIRMAR's CAST app has new user-friendly benefits:
Calibrate the DST810 in a simple, intuitive way from your mobile device.
Conduct basic and advanced heel-compensated speed calibrations for improved speed-through-water outputs across the speed range.
Advanced speed calibration allows for manual speed entries for multiple heel angles and up to 10 speeds, formerly only possible through expensive PC software.
Ultra-responsive speed begins as low as 0.3 knots and becomes linear at 0.6 knots.
Speed-through-water readings stay accurate and smooth through 45 knots.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
485.80 |
|
|
B60-12 12° Tilted Element Transducer with 6-Pin
The bronze B60-12° provide a vertical beam without a fairing. Inside the housing, the ceramic element is tilted to provide built-in deadrise compensation. The resulting vertical beam provides excellent echo returns for more accurate depth readings. The nearly flush housing minimizes drag with only 5 mm (3/16") extending outside of the hull.
Features:
Depth/Temp
50/200 kHz
600w RMS
Mid-performance
Bronze
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
336.82 |
|
|
B175H-W 1KW Bronze Thru Hull 12° Tilted Element
Features:
Installation: Thru Hull
Material: Urethane
Power (RMS): 1kW
Max Depth(ft): 800
Frequency (KHz): 150-250
Records: Depth and Temperature
Approved Hull Material: Fiberglass/Wood
Cable Length (ft/M): 6ft/2M
Supported deadrise: 8-15° Deadrise
Additional Notes: All wide beam products come with a 2M pigtail off the transducer. Requires a Transducer Extension cable for a Complete Transducer Installation. 10M Extension Cable part number A80327 and A80328 Single B75/B175 operation cable.
|
1565.21 |
|