|
9.6″ Dexter Vented Rotor Disc Brake Kit
Load Rite's 5-lug, 9.6-inch vented rotor disc brake kit is manufactured by Dexter and fits a standard 3,750 lbs capacity spindle.
Kit Includes:
Vented rotor with Galvx finish
Aluminum caliper with e-coat finish
Ceramic pads with backing plates
Galvanized heavy-duty mounting bracket
Dust cap, slider pins, and hardware
Pre-greased rotors include bearings, races, and seals
*Quantity (2) Kits Required Per Axle Assembly
|
296.51 |
|
|
12″ Dexter Vented Rotor Disc Brake Kit
Load Rite's 6-lug, 12-inch vented rotor disc brake kit is manufactured by Dexter and fits a standard 3,000-capacity spindle.
Kit Includes:
Vented rotor with Galvx finish
Aluminum caliper with e-coat finish
Ceramic pads with backing plates
Galvanized heavy-duty mounting bracket
Dust cap, slider pins, and hardware
Pre-greased rotors include bearings, races, and seals
*Quantity (2) Kits Required Per Axle Assembly
|
337.60 |
|
|
12″ AutoFlex Knott Disc Brake Kit
Load Rite's 6-lug, 12-inch vented rotor disc brake kit is manufactured by AutoFlex KNOTT and fits UFP 6,000 lbs. capacity 6-bolt axles. Does not fit Tie Down.
Kit Includes:
Vented cupped and studded, zinc rotor, and hub assembly
Loaded caliper assembly with pads
Full inner and outer bearings, races, and corresponding seal
Dust cap, lug nuts, and mounting hardware
*LH/RH Compatible
*Quantity (2) Kits Required Per Axle Assembly
|
393.60 |
|
|
10″ Knott Disc Brake Kit
Load Rite's 5-lug, 10-inch vented integral rotor disc brake kit is manufactured by AutoFlex KNOTT and fits KNOTT 3,700 lbs. capacity 5-bolt axles.
Kit Includes:
Vented cupped and studded, zinc rotor, and hub assembly
Loaded caliper assembly with pads
Full inner and outer bearings, races, and corresponding seal
Dust cap, lug nuts, and mounting hardware
*LH/RH Compatible
*Quantity (2) Kits Required Per Axle Assembly
|
316.85 |
|
|
16,500lb Capacity Disc Brake Actuator with 2-5/16″ Coupler
The Model 16.5 works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the brakes on the tow vehicle. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in, sealed, independent dampening shock absorber controls the telescoping shock against the hitch.
Be sure to comply with the regulations for brakes in the state. Brake laws are sometimes minimum standards, and users may wish to add brakes to a trailer to meet minimum Gross Vehicle Weight Ratings (G.V.W.R.). Note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator.
The Model 16.5 Actuator is completely assembled and ready to bolt into place (tongue sizes: 3”x 4” & 3”x 5”, 9 ga. min.)
Features:
16,500 lbs. capacity
Fits 2-5/16″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 16,500 lbs.
Maximum Tongue Load: 1,650 lbs.
Minimum Tongue Weight: 5% of G.V.W.R.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as total gross weight.
|
883.36 |
|
|
6,600lb Disc Brake Actuator – Tie Down Engineering Model
The Model 660E works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the tow vehicle axle brakes. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in dampening shock absorber retards the telescoping shock against the hitch ball. Be sure to comply with the regulations for brakes in your state. Brake laws are sometimes minimum standards, and you may wish to add additional brakes to a trailer.
Read the tow vehicle's owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator. The Model 660E Actuator is completely assembled and ready to bolt into place, if not already installed. Manufactured for tongue sizes: 3”x 3”, 3”x 4” & 3”x 5”.
Features:
6,600 lbs. capacity
Fits 2″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 6,600 lbs.
Maximum Tongue Load: 650 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight).
|
329.21 |
|
|
20,000lb Capacity Disc Brake Actuator with 2-5/16″ Coupler
The Model works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the brakes on the tow vehicle. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in, sealed, independent dampening shock absorber controls the telescoping shock against the hitch.
Be sure to comply with the regulations for brakes in the state. Brake laws are sometimes minimum standards, and users may wish to add brakes to a trailer to meet minimum Gross Vehicle Weight Ratings (G.V.W.R.). Note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator.
Features:
20,000 lbs. capacity
Fits 2-5/16″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 16,500 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as total gross weight.
|
1121.09 |
|
|
7,500lb Disc Brake Actuator – Tie Down Engineering Model
The Model 750E works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the tow vehicle axle brakes. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in dampening shock absorber retards the telescoping shock against the hitch ball. Be sure to comply with the regulations for brakes in the state. Brake laws are sometimes minimum standards, and users may wish to add additional brakes to a trailer.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator. The Model 750E Actuator is completely assembled and ready to bolt into place if not all ready-installed. Manufactured for tongue sizes: 3”x 3”, 3”x 4", and 3”x 5”.
Features:
7,500 lbs. capacity
Fits 2″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 7,500 lbs.
Maximum Tongue Load: 750 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight).
|
418.24 |
|
|
8,500lb Disc Brake Actuator – Tie Down Engineering Model
The Model 850E works by the “surge” or “push” of the trailer toward the tow vehicle. This automatically synchronizes the trailer brakes with the tow vehicle axle brakes. When the trailer pushes against the tow vehicle, the actuator telescopes together and applies the force to the master cylinder, supplying hydraulic pressure to the brakes. The built-in dampening shock absorber retards the telescoping shock against the hitch ball. Be sure to comply with the regulations for brakes in your state. Brake laws are sometimes minimum standards, and users may wish to add additional brakes to a trailer.
Read the tow vehicle owner’s manual on towing capacity and other towing recommendations before installing brakes or this actuator. The Model 850E Actuator is completely assembled and ready to bolt into place if not all ready-installed. Manufactured for tongue sizes: 3”x 3”, 3”x 4” & 3”x 5”.
Features:
8,500 lbs. capacity
Fits 2″ in. hitch ball
For use with disc brakes
Maximum Actuator Capacity:
Gross Load: 8,500 lbs.
Maximum Tongue Load: 850 lbs.
The actual in-service rating is limited to that of the ball and hitch or the least-rated component on the tow vehicle or trailer being used, or the trailer manufacturer’s G.V.W.R. shown on the certification label, whichever is lower (note: G.V.W.R. is the Gross Vehicle Weight Rating, which includes the trailer and the load weight as a total gross weight).
|
550.45 |
|
|
Load Rite
Easy to load and unload - whether you're hauling an 11' jon boat, a pontoon boat, personal watercraft, motorcycle, snowmobile, a 34' sport boat, or even some garden mulch - nothing makes the ride smoother, the launch and load easier than a Load Rite.
|
|
|
9" x 12" Standard Performance Trim Tab Kit w/o Switch Kit- 12V
Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades
Kit Contents:
2 each of 12-gauge stainless steel Electro-Polished trim tab blades
2 each of #15054-001 actuators with 6' lead and Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (#116) upper mounting bracket with gland seal
2 each of #50014-001 (#119) lower mounting bracket
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 16' to 26'
Length of Tab: 9"
Width of Tab: 12"
Minimum Transom Height: 13.5"
Blades: 12 Gauge Stainless Steel
Finish: Electro-Polished
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
690.76 |
|
|
9" x 12" Edge Mount Trim Tab Kit without Switch Kit -12V
Lenco Electric Edge Mount Trim Tab Kits make your boat ride smoother, dryer, faster and with increased safety whether on a small skiff or a large yacht. The Lenco ball screw design is more reliable, three times more powerful and features an instant response, which makes them very user friendly compared to typical hydraulics. Lenco fast response electric actuators are fully submersible with all plug & play waterproof Deutsch connections. Edge Mount actuators mount at the trailing edge of the plane, requiring 4" (10.16 cm) less transom height than Lenco standard mount trim tabs.
Kit Contents:
2 each of 12-gauge stainless steel trim tab blades
2 each of #15054-001 actuator with 6' leads & Deutsch plugs
2 each of #30133-103 20' actuator extension wiring harnesses
2 each of #15085-001 (116) upper mounting brackets with gland seal
2 each of #50014-001 (119) lower mounting brackets
1 each of the Lenco owner’s / installation manual
All necessary stainless steel mounting hardware
Specifications:
Suggested Boat Length: 16' to 25'
Length of Tab: 9"
Width of Tab: 12"
Hinge Height: 2"
Minimum Transom Height: 13.5"
Blades: 12 Gauge Stainless Steel
Finish: Smooth
Switch Kit: Sold Separately
Class: Fuel Efficient
Compliance: CE Certified
Compatibility: Any Boat
Actuators: 12-volt
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
621.73 |
|
|
12" x 9" Electro-Polished Edge Mount Trim Tab Kit
12 Volt
Fast response electric actuators for precise control. Fully submersible. All Plug & Play Deutsch connections. Electro-Polished blades are constructed of 12-gauge 304 stainless steel with 1" turned up edges and an 85x inside taper and 1/8" diameter stainless steel hinge pin. The actuators mount at the trailing edge of the blades, requiring 1/2" less transom height than the standard mount tabs.
Kits include:
(2) 12-gauge stainless steel Electro-Polished blades
(2) 15054-001 actuator with 6' leads and Deutsch connectors
(2) 30133-103 20' actuator extension wiring harnesses
(2) 15085-001 upper mounting brackets with gland seal
(2) 50014-001 lower mounting brackets
Lenco owner's/installation manual
Stainless steel mounting hardware
Specifications:
Boat Length:14' - 18'
L" x W":12" x 9"
Hinge Height:2"
Minimun Transom Height:11"
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
658.37 |
|
|
Pontoon Pump Discharge Hose Kit
Draining water from aircraft pontoons and floats into a container is so much easier with Beckson’s Pontoon Pump Discharge Kit! Factory fitted with an extra long, 6" (15.2 cm) rigid dispensing spout, the hose fits securely into a five gallon or other large container for proper disposal of water.
Specifications:
Hose Length: 3' (.9M)
|
21.73 |
|
|
Golf Cart Package with 6.5" Black Speakers, Amplifier, Amp Kit & Bluetooth Remote
Upgrade your golf cart to capture the sound of music while on the front 9 of any course or just cruising around.
If streaming music is on your mind, then this DS18 Bluetooth package will add connectivity to your golf cart with the user-friendly BTRC-SQ Bluetooth Audio Receiver. This unit will send out signals to your amplifiers and give you control over the music being played via Bluetooth.
The MP6 2-Way Marine Speaker is the newest arrival to the MP series of marine speakers. These speakers come in 2-way configurations and have an IPX5 Waterproof Rating so this product is built to endure all the elements out on the course. You can get the complete sound you crave on-demand with these speakers.
Also included is the SELECT 2 Channel amplifier, a compact and powerful (1800 Watts Max) amplifier that’s perfect for any golf cart audio system. This amplifier is designed for people who want a very small audio footprint, while also having the benefits of a huge amplifier putting out lots of power in a small package.
We’ll make sure you have everything you need to easily hook up your amplifier with an installation kit. DS18 kits are made with true gauge wire, heavy-duty hardware, fusing, and signal cables for long-lasting installations.
Features:
Bluetooth connectivity via Android and iPhone
High-quality sound
Easy to install and use
Small equipment footprint
Waterproof speakers for complete protection and longevity
Technical Specifications:
Speaker Maximum Power - 180W
Speaker RMS Power - 60W
Speaker Dimensions (Diameter x Depth) - 7.16" x 3.8" (18.2 x 9.7 cm)
Amplifier Power - 1800W
Amplifier Channels - Two (2)
Amplifier Dimensions (L x W x D) - 7.4" x 5.83" x 1.87" (18.8 x 14.8 x 4.75 cm)
Bluetooth Wire Length - 4' (1.22 M)
Bluetooth Audio Receiver - AUX input and USB port
Bluetooth Dimensions (L x Depth x H) - 3.81" x 1.47" x 2.19" (9.7 x 3.74 x 5.58 cm)
In the Box:
1 x Pair of MP6 6.5" Speakers - Black
1 x SELECT 2 Channel Amplifier
1 x BTRC-SQ Audio Receiver
1 x AMPKIT8 Installation Kit
*Sold as an Individual
|
399.36 |
|