|
AMT 4230-97, Coolant Recirculating Pump 1 Phase, 115V, 3/8" NPT Female
3/8" BRONZE COOLANT RECIRCULATING PUMPS
Cast Bronze Construction
No Bottom Bearing!!!
Brass Column and Impeller Shaft
Bronze Self-cleaning Open Impeller
3/8" NPT Discharge Port
Maximum Flow 8 GPM
Maximum Head 10 ft.
Available with 115V AC Single Phase or 230V AC Three Phase Motors,1590 RPM
1/25 HP Totally Enclosed Fan Cooled (TEFC) Motor
Delivers up to 8 GPM and 4 PSI
The AMT Bronze Coolant/Recirculating pump has been manufactured for a wide variety of Industrial/Commercial Coolant and Recirculating applications. The absence of a bottom bearing makes the unit ideal for handling erosive liquids. A 36" 3-conductor power cord is included.
AMT Bronze Coolant/Recirculating pumps are reliable, cost effective and low maintenance. Many are readily available “Off-the-Shelf” for fast, 24 hour shipment. For use with non-flammable liquids compatible with pump component materials.
|
386.98 |
|
|
Amt 5351-95, Cast Iron Coolant Pump 230/460volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT OIL PUMPS
1/4 HP Totally Enclosed Motor (TEFC)
Three Phase Motor
230/460 volts 0.8/0.4 amps
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
Delivers up to 56 GPM and 26 PSI
3/4" FNPTOutlet
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
AMT Interchangeable Coolant/Oil pumps are reliable, cost effective and low maintenance. For use with non-flammable liquids compatible with pump component materials.
|
507.94 |
|
|
AMT 5391-95, Immersion Coolant Oil Pump 23gpm 230/460volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT/OIL PUMPS
Cast Iron Construction
1/4 HP 230/460V 3 Phase Immersion Type
Shaft Seal Material: Sealless Design
Speed (RPM): 3450
Type: IMM
Voltage: 230/460
Fluid Port: 0.5"
HP:1/4
Impeller Material: Stainless Steel
GPM: 23
Replacement for Standard Machine Tool Industry Pumps
Fuji: VKP-063A
Old Fuji: VKN-061A
Mitsubishi: NQ100J
Toshiba: OPF-100M
Hitachi: CPD-100M
Yasukawa: VFPC-100
Graymills: IMV-25
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
AMT Interchangeable Coolant/Oil pumps are reliable, cost effective and low maintenance. For use with non-flammable liquids compatible with pump component materials.
|
487.69 |
|
|
AMT 5390-95, Immersion Coolant Oil Pump 23gpm 115volt
INTERCHANGEABLE IMMERSION & SUCTION COOLANT OIL PUMPS
1/4 HP Totally Enclosed Motors (TEFC)
115/230 volts, 3.0/1.5amps
Single or Three Phase Motors
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
1/2 inch FNPT Ports
Delivers up to 23 GPM and 26 PSI
Replacement For The Following Standard Machine Tool Industry Pumps
Fuji: VKP-063A
Old Fuji: VKN-061A
Mitsubishi: NQ100J
Toshiba: OPF-100M
Hitachi: CPD-100M
Yasukawa: VFPC-100
Graymills: IMV-25
Gusher: VBV-14
AMT Interchangeable Coolant/Oil pumps are dependable, economical replacement pumps equivalent to units supplied with both domestic and foreign made machine tools such as Fuji, Mitsubishi, Toshiba, Hitachi and many others. These pumps are designed for the circulation and spraying of coolants and cutting oils. Pumps feature semi-open impellers that are ideal for handling some solids and fine contaminants.
|
502.04 |
|
|
AMT 5381-95, Immersion Coolant Pump Cast Iron 10gpm
INTERCHANGEABLE IMMERSION & SUCTION COOLANT/OIL PUMPS
1/8 HP Totally Enclosed Motor (TEFC)
Three Phase Motor
230/460 volts, 0.3/0.19 amps
Stainless Steel or Composite Semi-open Impeller Options
Immersion and Suction Types
Cast Iron Construction
Handles Viscosity up to 500 SSU
Standard Replacement for Machine Tool Industry
Delivers up to 10 GPM
3/8 inch outlet diameter
Able to pump liquid down to 2 inches
Replacement for to following Standard Machine Tool Industry Pumps
Fuji: VKP-053A
Old Fuji: VKN-051A
Mitsubishi: NQ-60J
Toshiba: OPF-60M
Hitachi: CPD-060M
Yasukawa: VFPC-061DIF
Graymills: IMV-08
Gusher: VBV-18
|
250.97 |
|
|
AMT 3682-95 Straight Centrifugal Pedestal Pump
Mechanical Seal: Buna-N
Maximum Temperature: 180° F
3/4 in. NPT Suction Ports
1/2 in. NPT Discharge Ports
Maximum Working Pressure: 75 PSI
Self-cleaning Impeller on General Service Models
Maximum Flow 35 GPM
Maximum Head 148 Ft.
Epoxy Coated Pedestal Drive and Discharge Port Rotates in 90° Increments on High Head Models
All pumps have Cast Iron Casing with Stainless Steel Impeller
AMT Straight Centrifugal Pedestal pumps are designed for continuous-duty OEM, Industrial/Commercial and processing applications including circulation, chemical processing, liquid transfer, heating and cooling. The high head models are ideal for sprinkler systems and pressure boosting.
Pull-from-the-rear design permits easy servicing without disturbing any piping. Pedestals feature CNC machined shafts with sealed ball bearings. AMT Straight Centrifugal Pedestal pumps are reliable, cost effective and low maintenance. For use with nonflammable liquids compatible with pump component materials.
|
380.84 |
|
|
AMT Pump 4861-97 Brz Centrifugal Pump 12V
1/8 HP, Totally Enclosed, Not Ventilated, 12 volt DC electric motor
Salt water resistant Naval Bronze construction
Semi-open, self-cleaning impeller that can handle solids to 3/16 inch diameter
Buna-N mechanical seal and O-ring
The AMT 4861-97 is a lightweight 12 volt pump that is designed for use in live tanks, chemical transfer, salt water and general dewatering applications.
Features durable bronze construction with 3/4 inch NPT input and output ports.
Pump is NOT self-priming and requires flooded suction.
|
363.29 |
|
|
AMT Pump MSV3-5-1P Multistage Mtr/Pmp 1Hp 115v
Multi-Stage Booster Pump – MSV3-5-1P, 5-Stage, 115-208-230 Volts
NEMA 56C, Dual Cycle 50 and 60 Hz, 1.0 HP, single phase, Totally Enclosed, Fan Cooled motor
Recommended to operate at or below the Best Efficient Point which is at 16 GPM and a Max Total Head of 105 feet
Cast Iron base and adapter
1 inch NPT cast iron flanges
304 series stainless steel components with Teflon wear rings
EPDM-Tungsten Carbide Seal that is easy to remove and replace
The AMT MSV3-5-1P is a non-self-priming/gravity feed, industrial pump with high pressure and low output. This unit is more commonly referred to as a jockey pump and is often installed for water transfer uses where no suction lift is required such as boiler feed, condensate return, high pressure washdown, irrigation, booster service, and fire protection/sprinkler systems. These pumps have NOT been investigated for use in drinking water systems.
|
1465.20 |
|
|
Amt 5764-95 Sub Shredder Pump 3" Npt
SUBMERSIBLE SHREDDER SEWAGE PUMP
Cast Iron with Stainless Steel Motor Housing
Carbide-Tipped Shredder Impellers
Spiral Shredder Mechanism Plate Surface Hardened for Enhanced Cutting Ability
Silicon Carbide Lower Seal
3" NPT Port Sizes
Max. Temperature 104° F
3 HP
230 Volt
AMT Submersible Shredder Sewage pumps feature an enhanced spiral shredder mechanism plate and carbide tipped impeller to prevent clogging and reduce maintenance when cutting through stringy, fibrous and sludge type waste. Applications include sewage pumping stations, septic tanks, sewage treatment plants, dirty water drainage, flood and emergency. Also ideal for grinder type solids reduction application. Motors are rated continuous duty and single phase models have thermal overload protection.
AMT Submersible Shredder Sewage Pumps are reliable, cost effective and low maintenance.
|
1824.94 |
|
|
Amt 4294-98 Centrif Pump, 1" Ss, Viton
1" SELF-PRIMING STAINLESS STEEL CENTRIFUGAL PUMPS
Investment Cast 300 Series Stainless Steel Construction
Mechanical Seal Options: Buna-N, Viton®, and Silicon Carbide
1" NPT Port Sizes
Self-priming to 6 ft.
ODP and TEFC, Single or 3 phase 56 frame motors
Available in 1/3 to 2 Horsepower
Delivers up to 66 GPM and 29 PSI
AMT 316 Stainless Steel Transfer pumps are designed to handle liquids and chemicals with specific gravities to 1.6. The pumps are particularly well suited to applications involving perchloroethylene (PCE). Built in handle for portability.
AMT Stainless Steel Transfer pumps are reliable, cost effective and low maintenance. Many are readily available “Off-the-Shelf” for fast 24 hour shipment. For use with non-flammable liquids compatible with pump component materials.
|
887.76 |
|
|
1" SELF-PRIMING STAINLESS STEEL CENTRIFUGAL PUMPS
Investment Cast 300 Series Stainless Steel Construction
Mechanical Seal Options: Buna-N, Viton®, and Silicon Carbide
1" NPT Port Sizes
Self-priming to 6 ft.
ODP and TEFC, Single or 3 phase 56 frame motors
Available in 1/3 to 2 Horsepower
Delivers up to 66 GPM and 29 PSI
AMT 316 Stainless Steel Transfer pumps are designed to handle liquids and chemicals with specific gravities to 1.6. The pumps are particularly well suited to applications involving perchloroethylene (PCE). Built in handle for portability.
AMT Stainless Steel Transfer pumps are reliable, cost effective and low maintenance. Many are readily available “Off-the-Shelf” for fast 24 hour shipment. For use with non-flammable liquids compatible with pump component materials.
|
979.30 |
|
|
AMT 3201-96, Laundry Tray Pump 1/4 HP 115V
GENERAL PURPOSE LAUNDRY TRAY PUMP
Cast Aluminum Construction
Buna-N Mechanical Seal and O-Ring
1-1/4" NPT Suction and Discharge Port
Self-cleaning, Semi-open Impeller
Continuous Duty Motor 1725 RPM, 1/4 HP 115VAC Single Phase Open Drip Proof (ODP) 48Z Frame
The AMT Laundry Tray pump is a single stage, multi-vane open impeller unit. It is designed as a laundry tray pump but can be used for most gravity fed general service pumping applications. The open impeller design makes it particularly adaptable to dirty as well as clean liquids and is inherently resistant to clogging.
The AMT Laundry Tray pump is readily available “Off-the-Shelf” for fast 24 hour shipment. For use with non-flammable liquids compatible with pump component materials.
|
282.56 |
|
|
Applications for the MDX-MT3-AM Magnetic Drive Pump include etching equipment, photographic processing equipment, ice flakers, plate processors, and marine air conditioning.
March Pump's industrial MDX-MT3-AM is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 9 gallons per minute at 1 foot, and its maximum head is 28 Feet (or around 12PSI). The standard wet end (the materials that come into contact with the solution) is composed of Ryton, Viton, and Ceramic. The inlet connection is 0.5 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 0.125 Horsepower Compressed Air Motor which requires 21PSI. The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March MDX-MT3-AM centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Max Flow
9 GPM
34 LPM
Max Head
28 FT
8.8 M
Power
.125 HP
.093 KW
Electrical
21PSI or 3CFM
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Ryton (Front and Rear Housing, Impeller), Ceramic (Shaft, Thrust Washer), Viton (O-Ring)
|
828.00 |
|
|
AMT 285P-95, Self-Priming Centrifugal Pump 3/4 HP, 3 PH, 230/460 V
Cast Iron Construction
Buna-N Mechanical Seal and O-Ring with optional Viton? or Silicon Carbide Mechanical Seal and O-ring
1" & 1-1/4" NPT Suction and Discharge Ports
Dual Volute Design Reduces Radial Load on Motor
Maximum Working Pressure 75 PSI
Maximum Temperature 180 F
Self-cleaning, Semi-open Impeller
|
595.69 |
|
|
AMT 5471-K8, Peo Fab SS Pump Less Motor
|
417.69 |
|