|
2116 HP Electric Downrigger (36"-60")
The number one choice in trolling performance for the charter captain. Equipped with heavy duty, adjustable dual rod holders and all the other great features of our heavy duty, High Performance Downriggers.
PRODUCT OVERVIEW:
Unbeatable pulling power lifts 15 lb. weights at 295 ft./min. and 20 lb. weights with ease at 260 ft./min.
Includes Illuminated, resettable, sealed and silent digital line counter
300 ft. of 180 lb. Test, HP Stainless Steel Downrigger Cable
Dual adjustable and stainless steel jacketed Rocket Launcher Rod Holder (No. 447)
Includes Scotty/Marinco™ Plug and Receptacle
Includes 1148 Weight Storage Hook and marine grade stainless steel boom
Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position
Multi-position auto-stop included (Use 1008 Stopper Beads to stop at any pre-set position)
Includes Power Grip Plus Line Release
1/2″ Kevlar drive belt by Optibelt™ – The same belts used by superior European auto manufacturers
Clutch brake with the largest braking surface in the industry
Includes 1026 Swivel Pedestal Mount with 16 available positions
Fully assembled and factory tested with complete saltwater protection
Downrigger Boom Length: 36″ – 60″ telescoping stainless steel boom
Downrigger Boom Diameter: 1 1/4″
Rod Holder Interior Diameter: 1.70″
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
912.02 |
|
|
High Performance Electric Downrigger
The High Performance Downrigger features a new illuminated digital line counter as well as the sleek new Rocket Launcher rod holder. Pre-spooled with the HP stainless steel downrigger wire, the HP models have unbeatle pulling power lifting 20 lb. weights with ease at 260 ft. / min, and 10 lb. weights at 312 ft. / min.
Includes:
36" - 60" telescoping stainless steel boom. 1 1/4" dia.
Illuminated, resettable, sealed and silent digital line counter
300 ft. of 180 lb. Test, 316 stainless steel downrigger wire
1/2" Kevlar drive belt by Optibelt TM - The same belts used
by superior European auto manufacturers
Clutch brake with the largest braking surface in the industry
Boom mounted adjustable Rocket Launcher Rod Holder
Swivel Pedestal Mount
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
834.01 |
|
|
No. 1116 Propack Depthpower Downrigger (36"-60")
The top choice of charter captains. This unit gives the versatility of a telescoping boom with the Dual Rod Holder option and Swivel Pedestal Mount.
PRODUCT OVERVIEW:
Fully adjustable decent speed, lifts 7 lb. weights at 235 ft./min. and 15 lb. weights at 203 ft./min.
Spray protected positive-drive depth counter and Kevlar drive belt by Optibelt™
250 ft. of 150 lb. Test, Stainless Steel Downrigger Cable
Includes 247 Dual Rod Holder – Two 10″ tube style rod holders
Includes Scotty/Marinco™ Plug and Receptacle
The lowest amperage draw of any downrigger made with less than 1/3 the battery draw than some of the competition
Includes 1148 Weight Storage Hook and marine grade stainless steel boom
Multi-position auto-stop included (Use 1008 Stopper Beads to stop at any pre-set position)
Includes 2 Power Grip Plus Line Releases
Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position
Includes 1026 Swivel Pedestal Mount with 16 available positions
Fully assembled and factory tested with complete saltwater protection
Downrigger Boom Length: 36″-60″ telescoping stainless steel boom
Downrigger Boom Diameter: 1 1/4″
Rod Holder Interior Diameter: 2 1/8″
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
719.72 |
|
|
No. 1091 - Longarm Downrigger Combo Pack (36"-60")
Ideal for big boats. All the same features as the 1090 plus with the addition of the Pedestal Swivel Mount.
PRODUCT OVERVIEW:
High speed, 2 ft. per turn of the spool coupled with an extended handle for extra leverage
Spray protected positive-drive depth counter
200 ft. of 150 lb. Test, Stainless Steel Downrigger Cable
Boom mounted adjustable 358 Rodmaster II Rod Holder
Marine grade stainless steel boom
Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position
Includes 1026 Swivel Pedestal Mount with 16 available positions
Clutch brake with the largest braking surface in the industry – In the event of a bottom hang-up, it will pay out to avoid loosing gear
Includes Power Grip Plus Line Release
Fully assembled and factory tested with complete saltwater protection
Downrigger Boom Length: 36″-60″ telescoping stainless steel boom
Downrigger Boom Diameter: 1 1/4″
Rod Holder Interior Diameter: 1.85″
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
389.56 |
|
|
Dual Rod Holder/Front Mount
Front-mount rod holder fits all 1 5/16" diameter Cannon booms, including telescopic boom. Also fits several other downrigger makes. Each holder has a separate angle adjustment. Comes with two rugged rod tubes with gimbal and drain hole, two aluminum tube clamps, and Lexan® dual-mounting bracked.
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
56.06 |
|
|
Swivel Base Rod Holders
RH570
Stainless Steel Side Mount w/ Swivel Base
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a inch stainless steel lock nut at the bottom of the rod holder.
|
210.00 |
|
|
Swivel Base Rod Holders
RH570XL
Stainless Steel Side Mount w/ Swivel Base Extra Long
This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface.
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
230.77 |
|
|
Dual Rod Holder
247
10" tube style rod holder. Gives you the ability to fish with 2 rods without mounting another rod holder. Designed for use with the No. 1026 Pedestal/Swivel Mount (Mounting hardware included).
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
77.62 |
|
|
9" Swivel Side Mount Rod Holder - 1-5/8" I.D.
316 Stainless Steel
Designed for applications where clamp-on or flush mount holders are not practical
Can be mounted on any vertical flat surface
White vinyl insert included to protect your rod
|
114.12 |
|
|
3 Hole Swivel Oval Head Rod Holder - 0° - 10-1/2"
Head Size: 3.85" x 4.88"
Angle: 0° Head
Length: 10-1/2"
Inner Diameter: 1-7/8"
|
130.43 |
|
|
3 Hole Swivel Oval Head Rod Holder - 15° - 10-1/2"
Head Size: 3.85" x 4.88"
Angle: 15° Head
Length: 10-1/2"
Inner Diameter: 1-7/8"
|
130.43 |
|
|
4 Hole Extra Long Swivel Rectangular Head Rod Holder - 0° - 12-1/2"
Head Size: 4.25" x 4.75"
Angle: 0° Head
Length: 12-1/2"
Inner Diameter: 1-7/8"
|
148.36 |
|
|
4 Hole Extra Long Swivel Rectangular Head Rod Holder - 15° - 12-1/2"
Head Size: 4.25" x 4.75"
Angle: 15° Head
Length: 12-1/2"
Inner Diameter: 1-7/8"
|
148.36 |
|
|
4 Hole Swivel Rectangular Head Rod Holder - 0° - 10-1/2"
Head Size: 4.25" x 4.75"
Angle: 0° Head
Length: 10-1/2"
Inner Diameter: 1-7/8"
|
143.46 |
|
|
4 Hole Swivel Rectangular Head Rod Holder - 15° - 10-1/2"
Head Size: 4.25" x 4.75"
Angle: 15° Head
Length: 10-1/2"
Inner Diameter: 1-7/8"
|
143.46 |
|