|
March 815-PL Beer Pump
March Pump's 815-PL Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7 gallons per minute at 4.5 feet, and its maximum head is 18.6 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The 815-PL Beer Pump motor has a six foot cord, a plug, and a base. The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius. The 815-PL Beer Pump pumps Hot Water and Hot Wort.
Unit System 60Hz 50Hz Max Flow
7 GPM
22.7 LPM
Max Head
18.6 FT
4.1 M
Power
.04 HP
.029 KW
Electrical
115V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Can handle liquids of 250F
Materials are FDA Food Compliant
With 6 Foot Cord and Plug
Components are UL Recognized
American Made
|
211.87 |
|
|
March 815 PL Beer Pump 115V
March Pump’s 815-PL Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7 gallons per minute at 4.5 feet, and its maximum head is 18.6 Feet (8PSI).
Wet End: Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Materials are FDA Food Compliant: Components are UL Recognized
Max Internal Pressure: 50 PSI / 3.4 bar
Max Liquid Temperature: 250 °F / 121 °C
Note: Product image may be different than actual product received.
The 815-PL Beer Pump has pumped Hot Water and Hot Wort.
March Pump’s 815-PL Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7 gallons per minute at 4.5 feet, and its maximum head is 18.6 Feet (8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 1/2 inch male pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The 815-PL Beer Pump motor has a six foot cord, a plug, and a base. The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
|
344.18 |
|
|
March 815 PL C Beer Pump
March Pump’s industrial 815-PL-C is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 8 gallons per minute at 3 feet, and its maximum head is 18.6 Feet (8PSI).
At 60Hz
SystemUS Metric
Max Flow8 GPM 30.3 LPM
Max Head18.6 FT 5.7 M
Power0.04 HP 0.029 KW
At 50Hz
USMetric
7.9 GPM30 LPM
13.5 FT4.1 M
0.04 HP0.029 KW
Electrical: 115V 50/60Hz or 230V 50/60Hz
Inlet: 3/8"FPT & 3/4"MPT
Outlet: 1/2"MPT
Wet End: Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Max Internal Pressure: 50 PSI / 3.4 bar
Max Liquid Temperature: 250 °F / 121 °C
Applications for the 815-PL-C Magnetic Drive Pump include home brewing, hot water systems, solar heating, and fryers.
The 815-PL-C has pumped Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water.
|
332.48 |
|
|
March Magnetic Drive Centrifugal Beer Pump 230V
Applications for the March 815-PL Magnetic Drive Pump include hot water systems, solar heating, fryers, beer pump.
March Pump's industrial 815-PL is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 7 gallons per minute at 5 feet, and its maximum head is 18.6 Feet (or around 8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
Unit System 60Hz 50Hz Max Flow
7 GPM
22.7 LPM
Max Head
18.6 FT
4.1 M
Power
.04 HP
.029 KW
Electrical
115V 50/60HZ or 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
|
352.95 |
|
|
March Pump's AC-5B-MD Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for homebrewing. It is capable of generating a maximum flow of 17 gallons per minute at 1 foot, and its maximum head is 27 Feet (or around 11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 225 Fahrenheit or 107 Celsius. The AC-5B-MD Beer Pump pumps Hot Water and Hot Wort.
Unit System 60Hz 50Hz Max Flow
17 GPM
60 LPM
Max Head
27 FT
6 M
Power
.125 HP
.093 KW
Electrical
115V 60Hz
Type
Metering Pump
Inlet
1"FPT
Outlet
1/2"MPT
Wet End
Polysulfone (Front and Rear Housing, Impeller), Stainless Steel (Magnet Shell, Shaft), Buna N (O-Ring), Ceramic (Thrust Washers)
Can handle liquids of 225F
Materials are FDA Food Compliant
American Made
Components are UL Recognized
|
580.13 |
|
|
IWAKI MD-55LFZ-115, MAG DRIVE PUMP 115V 1" PORTS HI PRESS
Mag Drive Centrifugal Pump and Motor Assembly, High head impeller, Carbon filled ETFE Fluoroplastic Construction, close coupled to a 1/8 Horsepower, 115 Volts AC, 1 Phase, TEFC Electric Motor. 1 Inch NPT Threaded Port Connections.
|
1281.60 |
|
|
Great gift for Father's day, get dad what he really wants!
Learn how to brew beer at home even faster with a Homebrew Beer Pump, now 10% OFF!
Get Coupon Here
Buy your Homebrew Beer Pump Now!
|
|
|
March 809-PL-HS Magnetic Drive Beer Pump
The March 809-PL-HS Home Brew Beer Pump is great for all your brewing needs.
The March 809 PL HS hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include brewing, home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Home Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
Unit System - 60Hz
Max Flow - 6 GPM - 18.9 LPM
Max Head - 12.1 FT - 2.5 M
Power - .04 HP - .029 KW
Electrical - 115V 60HZ
Type - Centrifugal Mag Drive
Inlet - 1/2"MPT
Outlet - 1/2"MPT
Wet End Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Can handle liquids of 250F Materials and is FDA Food Compliant with 6 Foot Cord and plug Components are UL Recognized.
Made in American
|
348.08 |
|
|
March Mag-Drive Centrifugal Pump Plastic 230V Hi Speed Beer Pump
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
Unit System 60Hz 50Hz Max Flow
6 GPM
18.9 LPM
Max Head
12.1 FT
2.5 M
Power
.04 HP
.029 KW
Electrical
230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Can handle liquids of 250F
Materials are FDA Food Compliant
With 6 Foot Cord and Plug
Components are UL Recognized
American Made
|
358.80 |
|
|
March 809 815 Series Mag-Drive Centrifugal Pumps Bronze Center Inlet 115V 4.5GPM
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze Center Inlet 115V 4.5GPM 3/4"MPT Inlet, 1/2"MPT Outlet
|
426.08 |
|
|
March 809 SS HS C Beer Pump
March Pump's 809-SS-HS-C Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7.5 gallons per minute at 3 feet, and its maximum head is 12.1 Feet (or around 5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.75 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The 809-SS-HS-C Beer Pump motor has a six foot cord, a plug, and a base. The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
Unit System 60Hz 50Hz Max Flow
7.5 GPM
26.4 LPM
Max Head
12.1 FT
2.5 M
Power
.04 HP
.029 KW
Electrical
115V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
3/4"MPT
Outlet
1/2"MPT
Wet End
Stainless Steel (Front and Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Can handle liquids of 250F
Materials are FDA Food Compliant
With 6 Foot Cord and Plug
Components are UL Recognized
American Made
|
466.37 |
|
|
March AC-5SSB-MD Magnetic Drive Beer Pump
March Pump’s AC-5SSB-MD Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for homebrewing. It is capable of generating a maximum flow of 17 gallons per minute at 1 foot, and its maximum head is 27 Feet (11PSI).
March Pump’s AC-5SSB-MD Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for homebrewing. It is capable of generating a maximum flow of 17 gallons per minute at 1 foot, and its maximum head is 27 Feet (11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Stainless Steel, Polysulfone, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 200PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
Electrical/Air: 115V 50/60Hz
Inlet: 1"FPT
Outlet: 1/2"MPT
Wet End: Polysulfone (Impeller), 316 Stainless Steel (Front and Rear Housing, Magnet Shell, Shaft), Buna N (O-Ring), Ceramic (Thrust Washers)
Can handle liquids of 250F: Materials are FDA Food Compliant
American Made: Components are UL Recognized
P/N: 0150-0208-0100 (115V)
|
860.16 |
|
|
March AC-5SSB-MD Magnetic Drive Beer Pump 230V
March Pump’s AC-5SSB-MD Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for homebrewing. It is capable of generating a maximum flow of 17 gallons per minute at 1 foot, and its maximum head is 27 Feet (11PSI).
March Pump’s AC-5SSB-MD Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for homebrewing. It is capable of generating a maximum flow of 17 gallons per minute at 1 foot, and its maximum head is 27 Feet (11PSI). The standard wet end (the materials that come into contact with the solution) is composed of Stainless Steel, Polysulfone, Buna N, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 200PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
Electrical/Air: 230V 50/60Hz
Inlet: 1"FPT
Outlet: 1/2"MPT
Wet End: Polysulfone (Impeller), 316 Stainless Steel (Front and Rear Housing, Magnet Shell, Shaft), Buna N (O-Ring), Ceramic (Thrust Washers)
Can handle liquids of 250F: Materials are FDA Food Compliant
American Made: Components are UL Recognized
P/N: 0150-0208-0200 (230V)
|
788.63 |
|
|
March 809 PL Magnetic Drive Centrifugal Pump
The March 809-PL is used to pump Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water
March Pump's industrial 809-PL is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 4.5 gallons per minute at 0.5 feet, and its maximum head is 4.3 Feet (or around 1.8PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polysulfone, Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.5 male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.01 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50 PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius
Unit System 60Hz Max Flow
4.5 GPM
Max Head
4.3 FT
Power
.01 HP
Electrical
115V 60HZ
Type
Centrifugal Mag Drive
Inlet
1/2"MPT
Outlet
1/2"MPT
Wet End
Polysulfone (Front Housing), Stainless Steel (Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
|
319.80 |
|
|
March 815 Series Mag-Drive Centrifugal Pumps
The March MAGNE-BOOST Hydronic hot water booster pumps are a non-self priming unit built to handle liquid transfer in heating and cooling operations. Typical applications include home heating systems, solar heating systems, heat recovery systems and recirculating water in domestic and commercial hot water tanks. These pumps are not food rated.
• Brewery pump - the March 809 and 815 series of pumps are commonly used by Home Brewers and Breweries.
• Maximum liquid temperature for the 809 and 815 series is 250 F.
• Port configurations include in-line and center inlet with side discharge.
• Construction materials: Bronze, Stainless Steel, Ryton/Polysulfil Plastic. Impellers are Teflon plastic.
• There are many motor options available Including AC, DC and High Speed versions for added flow.
March Pump Mag-Drive Centrifugal Pump Bronze 230V High Speed 7.2GPM 1/2"MPT Ports
|
428.03 |
|