Oberdorfer 700C-M19 Cent Pump 3/4Hp 115/230V  

BURKS 7WT5, PUMP SELF PRIME 115/230v 1PH 3/4HP Bronze Fitted Cast Iron Construction. Close Coupled to a 3/4 Horsepower, 3450 RPM, 115/230 Volts, 1 Phase Motor. Ports are 2 Inches NPT Inlet, 2 Inches NPT Outlet.   UNSPSC Code: 40150000

Iwaki MD-30RLT, 3/4 inch MPT in/outlet 480gph 120v Iwaki MD 30RLT Water Pump   Japanese pressure rated flow water pump. 3/4 inch MPT inlet and outlet. 1/16 HP Motor output. 3150 RPM motor speed. 0.8 amps. Max flow 10.0 GPM. 480 GPH at 6 feet of head. Max head 17.7 ft. Max system pressure 11.60 psi.   Iwaki water pumps are magnetic driven, seamless pumps for use on either freshwater or saltwater aquariums. These pumps have a low heat exchange rate combined with quiet operation. Also the Iwaki pumps have a highly durable and aquarium tested design.   WMD pumps have American Made Motors MD pumps have Japanese Made Motors RLT pumps are for pressure applications RZT pumps are for very high pressure applications RLXT pumps are for circulation and wet or dry return

Iwaki WMD-40RLT 3/4 inch MPT in/outlet 720gph 120v Iwaki WMD 40RLT Water Pump   American motor pressure rated water pump. 3/4 inch MPT inlet and outlet 1/12 HP Motor output. 3200 RPM motor speed. 120 volt 1.90 amps. Max flow 13.7 GPM. 720 GPH at 6 feet of head Max head 21.3 ft Max system pressure 14.22 psi.   WMD pumps have American Made Motors MD pumps have Japanese Made Motors RLT pumps are for pressure applications RZT pumps are for very high pressure applications RLXT pumps are for circulation and wet or dry return

Flotec FP4122 Well Pump 3/4Hp 115/230V Flotec Shallow Well Jet Pump, Cast Iron Construction, 3/4HP 115/230V, 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 14.4GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec FP4432 Vertical Deep Well Jet Pump 1 HP Vertical deep well jet pump can be used in 4" diameter or larger wells up to 260', or in 2" diameter wells up to 180'. KEY FEATURES Superior performance at depths to water of 50' or more Rugged, heavy-duty cast iron pump housing Ready-to-install 230 volt motor - see manual for 115 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  1 MAXIMUM CAPACITY:  12 GPM FLOW AT 50' LIFT and 40 PSI:  11 GPM MAX LIFT:  260' for 4" or larger well / 180' for 2" well PRESSURE SWITCH SETTING:  40/60 SUCTION PIPE SIZE:  1-1/4" NPT DRIVE PIPE SIZE:  1" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.6 amps on 230v / 19.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4222 Cast Iron Convertible Jet Pump 3/4 HP Cast iron convertible jet pumps can be used in shallow or deep well applications in " diameter wells or larger and are pre-set for 30-50 PSI operation. KEY FEATURES Superior performance at depths to water of 100' or less Rugged, heavy-duty pump housing Ready-to-install 230 volt motor - see manual for 115 volt conversion Pressure switch pre-wired with 30-50 PSI pressure setting WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Cast Iron HORSEPOWER:  3/4 MAXIMUM CAPACITY:  11.9 GPM (shallow setup) FLOW at 10' LIFT and 40 PSI:  10.8 GPM (shallow setup) MAX LIFT:  25' w/ shallow setup / 100' w/ deep well setup MAXIMUM PRESSURE:  60 psi w/ shallow setup / 54 psi w/ deep setup PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp for 230v / 20 amp for 115v MAXIMUM WATER TEMPERATURE:  140 F (60 C)

Flotec FP4822 Stainless Steel Shallow Well Jet Pump 3/4 HP Stainless steel shallow well jet pumps are heavy-duty, durable, corrosion resistant, high pressure and offer efficient non-stop operation for years. KEY FEATURES Superior performance at depths to water of 25' or less Heavy-duty, stainless steel pump housing for highest corrosion resistance Ready-to-install 230 volt motor - see manual for 115 volt conversion 1-1/4" NPT suction and 1" NPT discharge pipe sizes WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Stainless Steel HORSEPOWER:  3/4 MAXIMUM CAPACITY:  11 GPM FLOW at 10' LIFT and 40 PSI:  11 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  52 psi MAXIMUM INLET PRESSURE:   PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v MAXIMUM WATER TEMPERATURE:  122°F (50 °C)

Flotec FP2122 Submersible Well Pump 4" Flotec Submersible Well Pump, for 5" or Larger Wells, Stainless Steel Pump and Motor Housing, 7GPM Series, 2 Wire, 3/4HP 230V, 1-1/4”NPT Port, Water Filled Submersible Motor, Built-in Check Valve, No Control Box Required

Flotec FP4832 Shallow Well Jet Pump 1HP Flotec Shallow Well Jet Pump Stainless Steel Construction 1HP 115/230V 1-1/4”NPT Suction x 1” NPT Discharge Ports, up to 18.4GPM at 40psi Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Seal and Gasket Kit for FP4112, FP4212, FP4122, and FP4222 Works with Flotec jet pump models FP4112, FP4212, FP4122, and FP4222 Provides all seals and gaskets used in one of the above models

Flotec FP2211 2-Wire 4 Inch Submersible Well Pump, 115 Volts 1/2 HP 4" Submersible Pumps are the most economical, energy-efficient pumps for 4" wells or larger. They provide the optimum amount of water and pressure for general home and farm use.   KEY FEATURES For 4" inside diameter or larger wells Pumps from depths of 150ft Floating Stack Design for sand resistance and reduced sand locking Corrosion-resistant stainless steel pump and motor housing   WARRANTY   3 year limited warranty     HORSEPOWER:  1/2   PERFORMANCE SERIES:  10 GPM   VOLTAGE:  115v, 60 Hz   NUMBER OF WIRES:  2 plus ground   BODY CONSTRUCTION:  Stainless Steel and Thermoplastic   MAXIMUM CAPACITY:  13.6 GPM   OPERATION RANGE:  20' to 150'   MAXIMUM DEPTH-TO-WATER:  150'   MAX PSI:  105 psi   PUMP DIAMETER:  3.78"   DISCHARGE PIPE SIZE:  1-1/4" NPT     RECOMMENDED BREAKER:  25 amp

Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8 GPM FLOW at 10' LIFT and 40 PSI:  6.4 GPM MAX LIFT:  25' MAX PRESSURE:  77 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.4 amps VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  3/4 MAXIMUM CAPACITY:  12 GPM FLOW at 10' LIFT and 40 PSI:  9.7 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  78 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service. KEY FEATURES Superior performance at depths to water of 100' or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  9 GPM (shallow well setup) FLOW AT 10' LIFT and 40 PSI:  7.8 GPM (shallow well setup) MAX LIFT:  25' w/ shallow well jet kit / 70' w/ deep well jet kit MAX PSI:  62 psi (shallow well setup) PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" MINIMUM SUCTION PIPE SIZE:  1-1/4" DRIVE PIPE SIZE:  1" DISCHARGE PIPE SIZE:  1" MINIMUM DISCHARGE PIPE SIZE:  3/4" AMP DRAW:  9.9 Amps on 115V / 4.95 Amps on 230V VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 F (60 C)