|
2003 PowerPost High Amperage Cable Connector 3/8" Stud
Insulated single stainless steel stud terminates multiple large conductors.
Features:
Connects high amperage cables securely
Stud dimensions: 3/8" x 7/8"
Base Material is PBT UL94 V0
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
11.96 |
|
|
2002 PowerPost High Amperage Cable Connector 5/16" Stud
Insulated single stainless steel stud terminates multiple large conductors.
Features:
Connects high amperage cables securely
Stud dimensions: 5/16" x 7/8"
Base Material is PBT UL94 V0
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
11.96 |
|
|
PowerPost High Amperage Cable Connector #10 Stud
Features:
Insulated single stainless steel stud terminates multiple large conductors
Connects high amperage cables securely
Stud dimensions: #10-32 x 5/8"
Base Material is PBT UL94 V0
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
7.98 |
|
|
PowerPost High Amperage Cable Connector 1/4" Stud
Features:
Connects high amperage cables securely
Glass-Reinforced Nylon
48 Volts DC Maximum
Not rated - Amperage flows between terminals stacked on post and is determined by wire and terminals used
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
11.96 |
|
|
2011 PowerPost Mini High Amperage Cable Connector - 1/4" Stud
Insulated single stainless steel stud terminates multiple large conductors.
Features:
Connects high amperage cables securely
Stud dimensions: 1/4" x 3/4"
Base Material is PBT UL94 V0
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
7.98 |
|
|
2103 PowerPost Plus Cable Connector 3/8" Stud
Enables connection of multiple smaller wires in spaces where a traditional bus bar may not fit.
Features:
150 Ampere bus allows small wire connections at high amperage cable connections
Connects high amperage cables securely
Stud dimensions: 3/8" x 3/4"
Base Material is Black Nylon 8231 GHS
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
22.70 |
|
|
Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.
The AC-1A-MD-3/8 Part # 0115-0064-0300 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals. The AC-1A-MD-3/8 may have been modified to handle these chemicals.
March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
2.3 GPM
8.7 LPM
Max Head
4.6 FT
1 M
Power
.005 HP
.003 KW
Electrical
115V 60HZ 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
3/8"OD
Outlet
3/8"OD
Wet End
Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet
Part # 0115-0064-0300
|
227.18 |
|
|
Applications for the March AC-1A-MD-3/8 Magnetic Drive Pump include photographic processing equipment, refrigeration systems, and water displays.
The AC-1A-MD-3/8 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals. The AC-1A-MD-3/8 may have been modified to handle these chemicals.
March Pump's industrial AC-1A-MD-3/8 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 2.3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.375 inch smooth, and the outlet is 0.375 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-3/8 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.
Unit System 60Hz 50Hz Max Flow
2.3 GPM
8.7 LPM
Max Head
4.6 FT
1 M
Power
.005 HP
.003 KW
Electrical
115V 60HZ 230V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
3/8"OD
Outlet
3/8"OD
Wet End
Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet
|
205.73 |
|
|
2101 PowerPost Plus Cable Connector - 1/4" Stud
Enables connection of multiple smaller wires in spaces where a traditional bus bar may not fit.
Features:
150AMP bus allows small wire connections at high amperage cable connections
Connects high amperage cables securely
Stud dimensions: 1/4" x 1"
Base Material is Black Nylon 8231 GHS
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
22.70 |
|
|
2102 PowerPost Plus Cable Connector - 5/16" Stud
Enables connection of multiple smaller wires in spaces where a traditional bus bar may not fit.
Features:
150 Ampere bus allows small wire connections at high amperage cable connections
Connects high amperage cables securely
Stud dimensions: 5/16" x 3/4"
Base Material is Black Nylon 8231 GHS
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
22.70 |
|
|
Tinned Lug 4/0 AWG - 3/8" Stud Size - 10 Pack
Lugs are connection points that are created by crimping the connector onto a wire or cable. This connection, commonly referred to as a cold weld, creates a solid, long-lasting connection. Pacer lugs are made from 100% pure copper for high conductivity. This copper is fully annealed to prevent cracking while being crimped and while in service. These terminals are also tin-plated to prevent corrosion and many of these lugs are general-purpose seamless electrical terminals. They are commonly used with battery cables.
Features:
Tin-plated copper with no exposed seams offering 100% long-term conductivity
Tinned copper
Highly durable
Multitude of sizes
Easily terminated
Infield applications
Long-lasting
Compliances:
E.T.P. (Electrolytic Tough Pitch) CDA-110
ASTM-B-152 Copper
RoHS Compliant
CSA Approved
UL Approved
Specifications:
Wire AWG: 4/0 AWG
Stud Size: 3/8"
Length (inch): 2.344"
Width (inch): 0.984"
Clearance (inch): 0.547"
Package Size: Ten included
|
33.17 |
|
|
Tinned Lug 6 AWG - 3/8" Stud Size - 2 Pack
Lugs are connection points that are created by crimping the connector onto a wire or cable. This connection, commonly referred to as a cold weld, creates a solid, long-lasting connection. Pacer lugs are made from 100% pure copper for high conductivity. This copper is fully annealed to prevent cracking while being crimped and while in service. These terminals are also tin-plated to prevent corrosion and many of these lugs are general-purpose seamless electrical terminals. They are commonly used with battery cables.
Features:
Tin-plated copper with no exposed seams offering 100% long-term conductivity
Tinned copper
Highly durable
Multitude of sizes
Easily terminated
Infield applications
Long-lasting
Compliances:
E.T.P. (Electrolytic Tough Pitch) CDA-110
ASTM-B-152 Copper
RoHS Compliant
CSA Approved
UL Approved
Specifications:
Wire AWG: 6 AWG
Stud Size (inch): 3/8"
Length (inch): 1.406"
Width (inch): 0.609"
Clearance (inch): 0.406"
Package Size: Two included
|
4.80 |
|
|
Tinned Lug 2/0 AWG - 3/8" Stud Size - 2 Pack
Lugs are connection points that are created by crimping the connector onto a wire or cable. This connection, commonly referred to as a cold weld, creates a solid, long-lasting connection. Pacer lugs are made from 100% pure copper for high conductivity. This copper is fully annealed to prevent cracking while being crimped and while in service. These terminals are also tin-plated to prevent corrosion and many of these lugs are general-purpose seamless electrical terminals. They are commonly used with battery cables.
Features:
Tin-plated copper with no exposed seams offering 100% long-term conductivity
Tinned copper
Highly durable
Multitude of sizes
Easily terminated
Infield applications
Long-lasting
Compliances:
E.T.P. (Electrolytic Tough Pitch) CDA-110
ASTM-B-152 Copper
RoHS Compliant
CSA Approved
UL Approved
Specifications:
Wire AWG: 2/0 AWG
Stud Size: 3/8"
Length (inch): 2.063"
Width (inch): 0.813"
Clearance (inch): 0.500"
Package Size: Two included
|
8.35 |
|
|
Tinned Lug 3/0 AWG - 3/8" Stud Size - 10 Pack
Lugs are connection points that are created by crimping the connector onto a wire or cable. This connection, commonly referred to as a cold weld, creates a solid, long-lasting connection. Pacer lugs are made from 100% pure copper for high conductivity. This copper is fully annealed to prevent cracking while being crimped and while in service. These terminals are also tin-plated to prevent corrosion and many of these lugs are general-purpose seamless electrical terminals. They are commonly used with battery cables.
Features:
Tin-plated copper with no exposed seams offering 100% long-term conductivity
Tinned copper
Highly durable
Multitude of sizes
Easily terminated
Infield applications
Long-lasting
Compliances:
E.T.P. (Electrolytic Tough Pitch) CDA-110
ASTM-B-152 Copper
RoHS Compliant
CSA Approved
UL Approved
Specifications:
Wire AWG: 3/0 AWG
Stud Size: 3/8"
Length (inch): 2.172"
Width (inch): 0.906"
Clearance (inch): 0.500"
Package Size: Ten included
|
24.54 |
|
|
16-14 AWG Heat Shrink Ring Terminal - 3/8" Stud Size - 3 Pack
Ring terminals are used to connect wires to a connection point. They can easily be used with two or more wires. They offer a solid connection as the ring is fitted over a stud. This removes the possibility of the terminal disconnecting. Using the proper parts is essential to a high-quality electrical connection. Ring terminals are the most secure type of tongue-style terminal. They are known for their durability and ease of use.
Features:
Tinned copper
600 Volts
Operating temperature is -55°C to 125°C
Highly compliant
Benefits & Protections:
Solid connections
Extremely durable
Long-lasting
Tin-plated
Easy to install
Specifications:
Color: Blue
Wire AWG: 16-14 AWG
Stud Size (inch): 3/8"
Terminal Pad Width (inch): 0.55”
Package Size: Three included
|
2.40 |
|