|
Gasket Tailpiece - 2mm
Features:
Gasket Tailpiece
2mm
Specifically for Bow 35, 55, 60, 75, 80 & 95
|
4.72 |
|
|
As the Fall months creep into our calendars, boat owners in cooler climates acknowledge, with sadness, that it’s time to put the boat away.
Outside Storage?
It’s a thought and an option but consider that you may be threatened by snow build up, tornadoes or hurricanes. The success of storing your boat outside depends on how well your boat is protected from the conditions outdoors.
Rinse/Flush
Rinsing the outside of your boat and trailer thoroughly with fresh water will remove excess salt. Pay particular attention to your trailer’s leaf springs, wheel hubs and brakes that are constantly submerged during launching and retrieval of your boat.
Flush your engine's cooling system with fresh water in line with your engine manufacturer’s salt removal recommendations. This will minimize corrosion and overheating issues come spring.
Drain your boat of all water – bilge, head, sink lines, water tanks, sea-cocks, and pipes. If you are in an area with extended periods of freezing, put antifreeze in the low parts if there is still some water present.
Salt
Watch out for salt. Buy a good salt remover to minimize corrosion.
Add fuel stabilizer to top off your fuel tanks. Here is one recommended by CLR Marine.
Diesel Formula Fuel Stabilizer & Performance Improver - 32oz *Case of 4*
STA-BIL Diesel Formula Fuel Stabilizer is a diesel additive that keeps fuel fresh for quick, easy starts and maximized for engine performance. Designed for use with all diesel engines, and all diesel fuels, Sta-Bil Fuel Stabilizer Diesel formula prevents sludge and sediment formation, cleans and lubricates fuel injectors to improve performance and helps remove water. It is safe to use and recommended for use at every fill up, with the 32 ounce bottle treating up to 320 gallons of fuel.
Batteries
Remove the batteries from your boat and store in your garage or basement.
Batteries should be connected to a battery charger that will give them a good charge and one that w automatically switches to a float/trickle charge to keep your batteries topped up. Match your charger to the type of battery you are charging. Using a charger manufactured for lead acid batteries to charge an AGM (absorbent glass mat) battery will cause damage to the battery.
If you choose to keep your batteries in the boat, connect a solar trickle charger. These chargers will keep your batteries topped off without the hassle of removing heavy batteries from your boat.
Cleaning
Clean the exterior with the proper fiber glass or wood cleaner needed for your boat. Bright work can be cleaned by removing the wood or cleaning it as it is - installed. Be careful to not get the wood cleaner onto the deck surfaces. The exterior should be dried with a chamois cloth. Vinyl seat cushions and backs should be cleaned with vinyl cleaner. Hard surfaces inside the vessel can be wiped with all purpose cleaners. End your cleaning with a coat of wax to the exterior and polish. Don’t forget the bottom paint.
Before you store, spend the time to give your boat a thorough cleaning. CLR Marine has many products by trusted brands such as Powerhouse, Davis Instruments, Jabsco, Shurhold, and Swobbit, to help winterize and clean. You will be grateful in the spring during launch time that your boat is already clean as the new boating season begins.
Cover Up
If you store outside in your yard, driveway, or a boat yard, a boat cover is a must to prevent damage from winter conditions. Leaving your boat in the water is not recommended. The boat is exposed to rough weather, and has a greater possibility of sinking if you aren’t monitoring it often.
https://www.clrmarine.com/462m4/boat-outfitting/winter-covers.html
and
https://www.clrmarine.com/462m4/winterizing.html
Circle May 21, 2022, on your calendar. The date is almost ten days before Memorial Day, next year when most harbors open for the season. Start your prep work, tune-ups, sanding, and painting to get out on the water and a great boating season. In the meantime, during the cold winter months, cozy up to the fire and read your boating manuals, new safety regulations and weather information.
Fair winds and smooth sailing.
To obtain more information about the products and services mentioned in this article, please get in touch with CLR Marine https://www.clrmarine.com/.
_________________________________________________________________________
Award-winning author Cheryl Kuba has been at the helm for more than 30 years sailing the Great Lakes, with side trips to the British Virgin Islands and St. Maarten.
She has served as past- Commodore of Great Lakes Fleet 21 -Chicago region. 3happycampers.com
©Copyright Cheryl Kuba, 3happycampers.com, 2021.
|
|
|
Boat Outfitting Equipment and Supplies
When it comes time for outfitting your boat, you can get all your boating supplies and boating accessories from us. You will never need to go anywhere else for your boat outfitting, because we have all the boat supplies you need. If you're looking for anchors/chain/rope, anodes, antifouling systems or boarding ladders, we have you covered. We can also offer you a selection of bottom paint and bow thrusters to choose from. You may also want cleaning supplies that offer deck/galley options so you can get your boat sparkling and ready to enjoy. We also have display mounts and docking accessories to complete your outfitting needs.
|
|
|
Gasket & Seal Set for Helm Pumps MT30-MT140
Full service kit for VETUS Helm Pumps MT40 to MT140 (including the more recent MTP42, MTP53)
Consists of shaft seal (HS801 25 x 42 x 7mm) and back plate gasket (HS804).
|
25.55 |
|
|
OBERDORFER 10631 PLUS GASKET KIT FOR N992 & N992R
|
250.93 |
|
|
Bow Thruster - 220 KGF & 24V
VETUS bow thruster with 220 KGF thrust force, suitable for boats from 19.5 to 26 meters in length. 24 Volt version.
Features:
Advantages of VETUS bow thrusters
A single propeller creates less flow disturbance in the tunnel
The VETUS unique propeller blade design minimizes cavitation noise
Spiral gears minimize transmission noise
The use of a flexible coupling between the tailpiece and motor eliminates vibration
All VETUS systems use a streamlined tailpiece for optimum flow
A strong synthetic propeller eliminates corrosion and reduces weight
Systems are easy to install and are supplied with clear installation and operation instructions
VETUS systems use a new line of high-quality aluminum control panels that are interchangeable with older panels
All VETUS maneuvering systems meet the EMC requirements
Specifications:
Thrust (KGF): 220
Power (kW): 11
Internal Tunnel Diameter (mm): 300
Weight (kg): 68
Voltage (V): 24
Current Consumption (A): 760
Continuous Operating Time (min): 2,5
Ignition Protected: No
Proportional: No
Retractable: No
Extended Runtime: No
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
6524.10 |
|
|
Don't miss out the entire month of June with super savings up to $250 off Maxwell Windlasses. Maxwell products are renowned for their reliability and performance throughout the international marine leisure boat industry.
Sale valid now until June 30th, 2017.
Don't miss out the entire month of June with super savings up to $250 off VETUS Bow Thrusters. *Please note: Special Order VETUS Bow Thrusters are on sale also. VETUS develops products that are easy to install and need little maintenance.
Sale valid now until June 30th, 2017.
Specials Closeouts Remanufactured Rebates
|
|
|
Don't miss out the entire month of June with super savings up to $250 off Maxwell Windlasses. Maxwell products are renowned for their reliability and performance throughout the international marine leisure boat industry.
Sale valid now until June 30th, 2017.
Don't miss out the entire month of June with super savings up to $250 off VETUS Bow Thrusters. *Please note: Special Order VETUS Bow Thrusters are on sale also. VETUS develops products that are easy to install and need little maintenance.
Sale valid now until June 30th, 2017.
Specials Closeouts Remanufactured Rebates
|
|
|
BOW PRO 651 Bow Thruster 65KGF - 12V
Our BOW PRO thrusters are fitted with proven induction technology. This system makes the use of carbon brushes obsolete. As a result, the bow thruster is very quiet and has indefinite* run-time! The (AC) induction motor is controlled by the VETUS MCV motor controller. This in-house-engineered motor controller can handle both 12V, 24V and AC motors, making the new bow thruster suitable for almost all boats!
The BOW PRO thruster is controlled by a proprietary CANBUS protocol. There are two different panels available for this thruster; one fully-proportional basic panel and one fully-proportional panel with lock-function. This allows the boat to be moored without the use of ropes. Letting passengers board your vessel have never been this easy! Evolution is to continue on a set of good properties, so there are similarities with its predecessors: remained are the very silent propeller blades and the streamlined tailpiece. Retrofitting a BOW PRO thruster, therefore, is a piece of cake as the new motor is interchangeable with the tailpiece and flange of our thruster range.
Features:
Range of Boat Size: 34ft - 36ft
Thrust in pounds force: 143 lbs
Motor horse power: 4
Tunnel- center line below the waterline: 185MM
Voltage: 12V
Precision proportional control
Endurance Rated Run-time - up to 10 minutes (dependant on model) at full power
Maintenance-free brushless motor
Sealed ingression protection construction - motor sealed for improved corrosion resistance in damp bilge environments
Built-in over-temp and low battery voltage protection
Suitable for high demanding applications (e.g. for use in rental & charter vessels)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
3423.54 |
|
|
BOW PRO 301 Bow Thruster 30KGF - 12V
The BOW PRO thrusters are fitted with proven induction technology. This system makes the use of carbon brushes obsolete. As a result, the bow thruster is very quiet and has indefinite* run-time! The (AC) induction motor is controlled by the VETUS MCV motor controller. This in-house-engineered motor controller can handle both 12V, 24V and AC motors, making the new bow thruster suitable for almost all boats!
The BOW PRO thruster is controlled by a proprietary CANBUS protocol. There are two different panels available for this thruster; one fully-proportional basic panel and one fully-proportional panel with lock-function. This allows the boat to be moored without the use of ropes. Letting passengers board your vessel have never been this easy! Evolution is to continue on a set of good properties, so there are similarities with its predecessors: remained are the very silent propeller blades and the streamlined tailpiece. Retrofitting a BOW PRO thruster, therefore, is a piece of cake as the new motor is interchangeable with the tailpiece and flange of our thruster range.
Features:
Range of Boat Size: 20ft - 25ft
Thrust in pounds force: 66 lbs
Motor horse power: 2
Tunnel- center line below the waterline: 110MM
Voltage: 12V
Precision proportional control
Endurance Rated Run-time - up to 10 minutes (dependant on model) at full power
Maintenance-free brushless motor
Sealed ingression protection construction - motor sealed for improved corrosion resistance in damp bilge environments
Built-in over-temp and low battery voltage protection
Suitable for high demanding applications (e.g. for use in rental & charter vessels)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2534.46 |
|
|
BOW PRO 361 Bow Thruster 36KGF - 12V
The BOW PRO thrusters are fitted with proven induction technology. This system makes the use of carbon brushes obsolete. As a result, the bow thruster is very quiet and has indefinite* run-time! The (AC) induction motor is controlled by the VETUS MCV motor controller. This in-house-engineered motor controller can handle both 12V, 24V and AC motors, making the new bow thruster suitable for almost all boats!
The BOW PRO thruster is controlled by a proprietary CANBUS protocol. There are two different panels available for this thruster; one fully-proportional basic panel and one fully-proportional panel with lock-function. This allows the boat to be moored without the use of ropes. Letting passengers board your vessel have never been this easy! Evolution is to continue on a set of good properties, so there are similarities with its predecessors: remained are the very silent propeller blades and the streamlined tailpiece. Retrofitting a BOW PRO thruster, therefore, is a piece of cake as the new motor is interchangeable with the tailpiece and flange of our thruster range.
Features:
Range of Boat Size: 23ft - 28ft
Thrust in pounds force: 80 lbs
Motor horse power: 2
Tunnel- center line below the waterline: 125MM
Voltage: 12V
Precision proportional control
Endurance Rated Run-time - up to 10 minutes (dependant on model) at full power
Maintenance-free brushless motor
Sealed ingression protection construction - motor sealed for improved corrosion resistance in damp bilge environments
Built-in over-temp and low battery voltage protection
Suitable for high demanding applications (e.g. for use in rental & charter vessels)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
2828.78 |
|
|
BOW PRO 421 Bow Thruster 42KGF - 12V
The BOW PRO thrusters are fitted with proven induction technology. This system makes the use of carbon brushes obsolete. As a result, the bow thruster is very quiet and has indefinite* run-time! The (AC) induction motor is controlled by the VETUS MCV motor controller. This in-house-engineered motor controller can handle both 12V, 24V and AC motors, making the new bow thruster suitable for almost all boats!
The BOW PRO thruster is controlled by a proprietary CANBUS protocol. There are two different panels available for this thruster; one fully-proportional basic panel and one fully-proportional panel with lock-function. This allows the boat to be moored without the use of ropes. Letting passengers board your vessel have never been this easy! Evolution is to continue on a set of good properties, so there are similarities with its predecessors: remained are the very silent propeller blades and the streamlined tailpiece. Retrofitting a BOW PRO thruster, therefore, is a piece of cake as the new motor is interchangeable with the tailpiece and flange of our thruster range.
Features:
Range of Boat Size: 25ft - 30ft
Thrust in pounds force: 93 lbs
Motor horse power: 4
Tunnel- center line below the waterline: 125MM
Voltage: 12V
Precision proportional control
Endurance Rated Run-time - up to 10 minutes (dependant on model) at full power
Maintenance-free brushless motor
Sealed ingression protection construction - motor sealed for improved corrosion resistance in damp bilge environments
Built-in over-temp and low battery voltage protection
Suitable for high demanding applications (e.g. for use in rental & charter vessels)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
3083.01 |
|
|
BOW PRO 761 Bow Thruster 76KGF - 12V
The BOW PRO thrusters are fitted with proven induction technology. This system makes the use of carbon brushes obsolete. As a result, the bow thruster is very quiet and has indefinite* run-time! The (AC) induction motor is controlled by the VETUS MCV motor controller. This in-house-engineered motor controller can handle both 12V, 24V and AC motors, making the new bow thruster suitable for almost all boats!
The BOW PRO thruster is controlled by a proprietary CANBUS protocol. There are two different panels available for this thruster; one fully-proportional basic panel and one fully-proportional panel with lock-function. This allows the boat to be moored without the use of ropes. Letting passengers board your vessel have never been this easy! Evolution is to continue on a set of good properties, so there are similarities with its predecessors: remained are the very silent propeller blades and the streamlined tailpiece. Retrofitting a BOW PRO thruster, therefore, is a piece of cake as the new motor is interchangeable with the tailpiece and flange of our thruster range.
Features:
Range of Boat Size: 35ft - 39ft
Thrust in pounds force: 167 lbs
Motor horse power: 6
Tunnel- center line below the waterline: 185MM
Voltage: 24V
Precision proportional control
Endurance Rated Run-time - up to 10 minutes (dependant on model) at full power
Maintenance-free brushless motor
Sealed ingression protection construction - motor sealed for improved corrosion resistance in damp bilge environments
Built-in over-temp and low battery voltage protection
Suitable for high demanding applications (e.g. for use in rental & charter vessels)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
3809.03 |
|
|
BOW PRO 571 Bow Thruster 57KGF - 12V
The BOW PRO thrusters are fitted with proven induction technology. This system makes the use of carbon brushes obsolete. As a result, the bow thruster is very quiet and has indefinite* run-time! The (AC) induction motor is controlled by the VETUS MCV motor controller. This in-house-engineered motor controller can handle both 12V, 24V and AC motors, making the new bow thruster suitable for almost all boats!
The BOW PRO thruster is controlled by a proprietary CANBUS protocol. There are two different panels available for this thruster; one fully-proportional basic panel and one fully-proportional panel with lock-function. This allows the boat to be moored without the use of ropes. Letting passengers board your vessel have never been this easy! Evolution is to continue on a set of good properties, so there are similarities with its predecessors: remained are the very silent propeller blades and the streamlined tailpiece. Retrofitting a BOW PRO thruster, therefore, is a piece of cake as the new motor is interchangeable with the tailpiece and flange of our thruster range.
Features:
Range of Boat Size: 28ft - 34ft
Thrust in pounds force: 125 lbs
Motor horse power: 4
Tunnel- center line below the waterline: 150MM
Voltage: 24V
Precision proportional control
Endurance Rated Run-time - up to 10 minutes (dependant on model) at full power
Maintenance-free brushless motor
Sealed ingression protection construction - motor sealed for improved corrosion resistance in damp bilge environments
Built-in over-temp and low battery voltage protection
Suitable for high demanding applications (e.g. for use in rental & charter vessels)
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
3434.07 |
|
|
Newbury, Massachusetts, April 15th, 2010: Technology changes rapidly and as a company building WiFi equipment, Island Consulting strives to offer the best. Since the beginning, Island Consulting has continuously made improvements to The Wirie, a long range WiFi solution for boats and RVs. The most recent development in creating a better product involves a high-end marine grade WiFi antenna. To achieve this goal, Island Consulting partnered with the well-known US antenna manufacturer, L-com.
L-com, a leading antenna manufacturer in the wireless connectivity business for over 27 years, agreed to produce a marine grade antenna exclusively for The Wirie. Designed to stringent specifications, the new Wirie antenna is an 8dBi omni-directional high performance marine antenna that features sealed collinear brass elements inside a durable UV-stable white fiberglass radome. The sealed end cap ensures no water entry and drain holes in the base help prevent moisture build-up inside the antenna.
The collaboration between Island Consulting and L-com offers the consumer an economical alternative to other true marine grade WiFi devices currently on the market. “We believe our partnership with L-com has allowed us to turn The Wirie into the most durable and best long range WiFi solution available for boats and RVs”, states Mark Kilty from Island Consulting. According to Karl Blomgren, L-Com's Product Manager, “L-Com is always interested in working with customers, like Island Consulting, to optimize our antennas for their applications to support new product enhancements.” Additional information about The Wirie's new antenna can be viewed at www.thewirie.com/antennadetails.html.
For $250, The Wirie enhances the customers' ability to connect to the internet from the comfort of his/her own boat or RV. The Wirie continues to offer many unique features: flexible stainless steel mounting bracket, easy to install and use software, comprehensive user manual, powerful 1000mW WiFi adapter, IP67 waterproof box, and superior customer support. The Wirie is easy to upgrade as technology continues to advance. In addition to the new antenna, the warranty of The Wirie has been extended to 1 year. The 10-day money back guarantee is still in place.
Through the joint effort between Island Consulting and L-com, The Wirie is a truly marine grade WiFi solution at an affordable price.
For more information, please visit www.thewirie.com.
About The Wirie:
Island Consulting located in Newbury, Massachusetts, USA, manufactures and distributes The Wirie. The Wirie was invented in the Caribbean in April 2009 to provide a cost-effective, user-friendly, long range WiFi solution for boats and RVs. It was quickly expanded to a U.S. operation to allow a larger distribution. Island Consulting is committed to continuous improvements and to making sure every customer is extremely satisfied. Website: www.thewirie.com
About L-com:
Founded in 1982, L-com Global Connectivity is a privately held corporation in Massachusetts, USA, dedicated to the design and production of a wide range of interconnect products for the electronics and data communication industries. L-com places primary product emphasis on copper and fiber cable assemblies, wireless antennas and amplifiers and accessories for modular, coaxial and computer networking applications. In June 2007, L-com acquired HyperLink Technologies of Boca Raton, Florida, USA. Website: www.L-com.com
Contact:
Liesbet Collaert
liesbet@thewirie.com
http://www.thewirie.com
The Wirie can now be found at CLR Marine.
http://www.clrmarine.com/462.html?m4:cat=%2FCOMMUNICATION
http://www.clrmarine.com/462.html?m4:cat=%2FCOMMUNICATION%2FAntennas
http://www.clrmarine.com/462.html?m4:cat=%2FCOMMUNICATION%2FMobile%20Broadband
http://www.clrmarine.com/m4_view_item.html?m4:item=0Wirie
|
|