Marine Kettle® Pow'r GripFish Rod Holder Mount Made of 18-8 stainless steel and cast 356 hard anodized aluminum to endure the most severe marine environment.  This versatile mount fits most cylindrical type rod holders and allows grills to mount in any direction from the rod holder.  Its unique quick disconnect system allows instant installation or storage after use without tools.  Compatible With: Marine Kettle® Grills *Sold as an Individual 

Marine Kettle® Bulkhead or Square/Flat Rail Mount  This all 18-8 stainless steel mount attaches to any vertical flat surface such as bulkheads, hulls, transoms or cabin sides.  Also mounts to square or flat rails.  Fits horizontal rails up to 2-1/4" (57 mm) high by any depth or vertical  up to 1- 5/8" (41 mm) wide by any depth.   Rod portion of mount quickly disconnects for easy storage.  Some fasteners required for installation. Compatible With: Marine Kettle® Grills *Sold as an Individual 

ShadeFin with Black Fabric, Case & Fixed Rod Holder Mount Kit Add an extra layer of sun protection with ShadeFin by TACO Marine that easily attaches into rod holders, tops and arches for convenient, portable shade for almost any boat. ShadeFin’s ocean-inspired design provides expanded shade coverage for multiple areas of the boat, including fore, aft and sides of tops or anywhere there is a rod holder. ShadeFin’s fabric provides an excellent UPF 50+ rating of sun protection while boating and fishing, or when relaxing at the dock and sand bar. To anticipate the needs of many boaters, ShadeFin is available with either a fixed or adjustable rod holder mount, which inserts into any standard rod holder, or with a clamp-on mount for pipe or tube.  ShadeFin’s body houses the ribs and material, and is offered in all black or white. A protective mesh storage sleeve comes standard with the ShadeFin. To operate ShadeFin, remove the sleeve, mount to a desired location onboard and activate the underside release tabs. Structural ribs attached to weather-resistant sun-protecting fabric expand out from the body to lock the fin in place. ShadeFin is lightweight, portable and requires no drilling. Features: Light, compact and portable Easily mounts into any standard rod holder Kit comes with a Fixed Rod Holder Mount Adjustable Rod Holder Mount options available Clamp-on mounting options available for 3/4”, 1” schedule-40 Pipe and 1-1/4” O.D. tube Large coverage area of 5’ X 6’ UPF (Ultraviolet Protection Factor) rating of 50+ (“Excellent” rating) Made of high-quality anodized aluminum parts

ShadeFin with White Fabric, Case & Fixed Rod Holder Mount Kit Add an extra layer of sun protection with ShadeFin by TACO Marine that easily attaches into rod holders, tops and arches for convenient, portable shade for almost any boat. ShadeFin’s ocean-inspired design provides expanded shade coverage for multiple areas of the boat, including fore, aft and sides of tops or anywhere there is a rod holder. ShadeFin’s fabric provides an excellent UPF 50+ rating of sun protection while boating and fishing, or when relaxing at the dock and sand bar. To anticipate the needs of many boaters, ShadeFin is available with either a fixed or adjustable rod holder mount, which inserts into any standard rod holder, or with a clamp-on mount for pipe or tube.  ShadeFin’s body houses the ribs and material, and is offered in all black or white. A protective mesh storage sleeve comes standard with the ShadeFin. To operate ShadeFin, remove the sleeve, mount to a desired location onboard and activate the underside release tabs. Structural ribs attached to weather-resistant sun-protecting fabric expand out from the body to lock the fin in place. ShadeFin is lightweight, portable and requires no drilling. Features: Light, compact and portable Easily mounts into any standard rod holder Kit comes with a Fixed Rod Holder Mount Adjustable Rod Holder Mount options available Clamp-on mounting options available for 3/4”, 1” schedule-40 Pipe and 1-1/4” O.D. tube Large coverage area of 5’ X 6’ UPF (Ultraviolet Protection Factor) rating of 50+ (“Excellent” rating) Made of high-quality anodized aluminum parts

Pow'r Grip LeveLock Double Locking Fish Rod Holder Mount  Just when you thought it couldn't get any better.....this mount adjusts and locks in place at both ends.   We've joined the "LeveLock" Adjustable Fish Rod Holder Mount, with the "Pow'rGrip" Adjustable Fish Rod Holder Mount.  This allows the "Pow'rGrip" portion of the mount to adjust to any size rod holder and lock in place, while the "LeveLock" portion of the mount, adjusts and locks your Magma rectangular grill.  This mount is the strongest, most corrosion resistant, most versatile mount in the industry. Compatible With: Rectangular Grills and Single Mount Tables Technical Specifications: Material - 18-8 Stainless Steel and 356 Anodized Aluminum  Dimensions W x H) - 3-5/8" x 8" (9.3 x 20.3 cm) Weight - 1.77 lb (.81 kg) *Sold as an Individual 

Adjustable All-Angle Fish Rod Holder Mounted Kayak/SUP Rack No more tripping over your kayak or paddleboard when stored on the deck or lugging them around after a long day on the water.   With Magma’s Fish Rod Holder Mounted Removable Kayak / SUP Rack your problems are solved.  This convenient storage rack, easily attaches to most standard fish rod holders, has been constructed from 1” Dia., 304 marine grade Stainless Steel tubing, aircraft quality hard anodized 356 aluminum, and includes stainless steel attachment fasteners.  Designed to fit most standard fish rod holders up to 1-1/2” (38mm) inside diameter and is wide enough to fit all of the most popular kayak or board sizes.  Magma’s patented LeveLock® all-angle adjustable mounting bracket and the Pow’rGrip adjustable quick release rod holder system allows each arm to be instantly installed and adjusted without tools.  Each arm comes with pre-installed UV resistant padding and has two tie-down attachment points for securing straps when underway or simply use them with a cable lock to safely store your toys when at the dock.   Whether you’re new to water sports or a seasoned veteran, this rack is a must have for the paddling enthusiast who’s always on the go. Features: Holds a single kayak or 2 or more standard SUP’s Allows quick installation or removal without tools for convenient storage Technical Specifications: Material - 304 Marine grade Stainless Steel Bracket Height (w/o mount) - 26.84" (68.18 cm) Weight (Pair) - 12.4 lbs (5.63 kg) *Sold as a Pair

Marine Kettle Mounting 8" Extension This Stainless Steel extension adds 8" (20.3 cm) to Marine Kettle grill mounting brackets.  Compatibility: Compatible with all Magma Marine Kettles "A10" series mounting brackets NOT compatible with marine kettle pedestal mount or table top legs *Sold as an Individual 

Adjustable Grill Rod Holder Mount The Kuuma Pivoting Rod Holder Mount fits securely into any 1-5/8" I.D., flush mount fishing rod holder and instantly converts it to a fully adjustable grill mount.  The stainless inner tube telescopes out of the anodized aluminum outer tube making the overall height adjustable from 14.8" to 18.8".  The mounting plate is compatible with all Kuuma grills, as well as most rectangle-style Magma grills (Magma and Kuuma grill mounting hardware included).  The mounting plate swivels around a ball joint, making it freely adjustable to whichever angle best suits your grilling needs.  Both the telescoping tube and swiveling mounting plate feature a tension clamp, keeping the Rod Holder Mount securely locked in the position you choose.  Compatible With: All Kuuma grills Features: Fits into 1-5/8" I.D. fishing rod holders of all angles to create a level grill mount Mounting plate pivots and rotates 360-degrees around ball joint  Stainless Steel inner tube telescopes out 4-inches Tension clamps securely locks the pivoting and telescoping joint Rugged reinforced nylon, anodized aluminum and Stainless Steel construction *Sold as an Indivudual WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ShadeFin™ Telescopic Rod Holder Mount Wherever you are onboard, ShadeFin can follow! The Telescopic Rod Holder Accessory for ShadeFin – a versatile attachment option that inserts into standard gunnel rod holders for portable, adjustable boat shade. Made from high-quality, lightweight anodized aluminum, the Telescopic Rod Holder Accessory extends from 42" to 67" tall – elevating ShadeFin over the deck for boaters to comfortably stand underneath. For boaters at the dock, sandbar, or in the water, the Telescopic Rod Holder Accessory can also be adjusted to position ShadeFin over the side of the boat – keeping you protected from the sun. Easily Adjustable As the sun changes position, the angle and height of this accessory can easily be adjusted at two points along its body – the bottom joint and the throw latch. Toward the base, the bottom joint features a Sure-Grip Knob and Pull Pin Lock that enables the adjustment of the accessory's upward angle. The throw latch half-way up the body is used to adjust the height and 360° rotation of the ShadeFin. If using this accessory with the Adjustable Rod Holder Mount, the angle of ShadeFin can also be adjusted from the Sure-Grip Knob at the top.  Operation To use the Telescopic Rod Holder Accessory, simply insert the solid gimbal butt into any standard rod holder on the gunnel, remove the Pull-Pin, adjust the upward angle using the Sure-Grip Knob at the bottom joint to the desired 0°, 15°, or 30°, and reinstall the Pull Pin. Then, at the top, simply insert the Fixed or Adjustable Rod Holder Mount into the opening. The mount will secure in place when its gimbal butt seats into the Accessory gimbal pin. Then attach ShadeFin into the Mount, as directed in the Instruction Manual, and deploy. Use the throw latch to adjust the ShadeFin height and horizontal rotation. Features: Features Sure-Grip Knob at the joint with a secure Pull Pin Lock Features a throw latch for secure height adjustment from 42" to 67" Features solid aluminum gimbal butt and internal Delrin bearings High-quality drawn aluminum tube Pairs with T10-3000-5 or T10-3000-6 at the top sold separately 1-year limited warranty

LeveLock All-Angle Fish Rod Holder Mount The LeveLock fish rod holder mount is Magma's most popular mount and is constructed of marine grade Stainless Steel tubing and anodized Aluminum components.  These components have been hard anodized to aircraft quality for extremely high corrosion resistance.  With an increased adjustment range and sturdy draw tight handle design this heavy duty mount is the strongest, most corrosion resistant and most versatile mount available on the market. Compatible With:  Rectangular Grills and Single Mount Tables *Sold as an Individual 

ShadeFin Mini Rod Holder Mount Designed for standard rod holders, the ShadeFin Mini Rod Holder Mount is a simple solution for adding boat shade onboard. Simply insert the mount at the bottom edge of the post, tighten it until snug, and attach ShadeFin Mini. The ShadeFin mini rod holder mount can safely remain in the rod holder when not in use or be easily removed by loosening and stowing. Features and Benefits: Fits standard rod holders with an inside diameter of 1.75" or greater Constructed out of aluminum-grade 6061 alloys Includes a stainless steel Type-304 threaded rod with an injection-molded nylon cap 3-year limited warranty Specifications: Finish: powder-coated, misty silver Length (inch): 9-1/4"

ShadeFin Adjustable Rod Holder Mount Lightweight and versatile, the Adjustable Rod Holder Mount for ShadeFin makes adding shade to your boat easy! Sliding the gimbal-slot butt end over the rod holder’s gimbal pin makes a secure, quick connection. A beveled, nylon sleeve is included, in the instance the rod holder opening is oversized for the mount’s shaft. Verify that the gimbal slot on the mount is mated with the pin in the rod holder, or Adjustable Telescopic Gunnel-Mount, insert the ShadeFin, adjust to your preferred shade angle and enjoy. Features: Manufactured from Type-316L stainless steel Features soft-touch knob for easy and secure angle adjustment Adjusts every 15º with safety detents Gimbal-slot butt end for secure rod holder placement Features white nylon sleeve for additional rod holder stabilization Includes self-aligning notch and pin-locking hole 1-year limited warranty

ShadeFin Fixed Rod Holder Mount Enjoy your ShadeFin in any standard rod holder with our Fixed Rod Holder Mount. Simply install by inserting the Fixed Rod Holder Mount into a firmly welded rod holder. Sliding the gimbal-slot butt end over the rod holder’s gimbal pin with the open end out makes a secure, quick connection. A beveled, nylon sleeve is included, in the instance the rod holder opening is oversized for the mount’s shaft. Verify that the gimbal slot on the mount is mated with the pin in the rod holder or Telescopic Rod Holder Mount, attach the ShadeFin and enjoy! Features: Manufactured from high-polished Type-304 stainless steel Gimbal-slot butt end for secure rod holder placement Features white nylon sleeve for additional rod holder stabilization Includes self-aligning notch and pin-locking hole 1-year limited warranty

Triple Rod Holders Scotty's fully-adjustable multiple rod holder comes with a built-in lure and accessory rack, which gives you quick access to your lures and tools. Includes No. 241 combination deck or side mount. Made from fibre reinforced engineering nylon. Triple Rod Holder Mount Includes Mounting bracket WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Marine Kettle® Charcoal Grill - 15" Our time tested original charcoal Marine Kettle® grill now has a hinged lid.  Made in the U.S.A., it is meticulously crafted of 100% 18-8 mirror polished stainless steel for maximum corrosion resistance.  Our rotating design allows you to determine which direction you would like the lid to open when grilling in windy conditions.  You obtain perfect results through use of the adjustable height cooking grill and the variable temperature control draft door assembly.  Our Marine Kettle® design allows oven type baking to enhance the grill flavor while retaining the natural juices of the food.  It will cook more food faster, on less grill area, than any other charcoal grill.  Safety and efficiency are obtained by closing the draft door and extinguishing the coals for future use.  Magma’s large selection of mounting options and accessories allows you to customize your grill for your specific on-board or on-shore application.   *Mount not included.  Features: Heat resistant "Stay Cool" plastic handle with air cooled supports Perfectly balanced hinged lid, won't slam shut Adjustable height cooking grill and variable draft door assembly, for superior temperature control Lower charcoal grate and sealed ash compartment Technical Specifications: Material - 18-8 mirror polished marine grade Stainless Steel Mounting Application - Marine Kettle® Mounts Primary Cooking Grate - 15" (38.1 cm)  Total Cooking Area - 177" Sq. In. (1141.9 sq. cm) Dimensions w/valve attached and lid/legs closed (L x W x H) - 14-7/8" x 14-7/8" x 11" (37.8 x  37.8 x 27.9 cm) Weight - 7.92 lb (3.6 kg) Fuel Type - Charcoal *Sold as an Individual