Vehicle Base Ford F-150 (2004-2010) Ford F-150 (2004-2010) Lincoln Mark LT (2005-2010) This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. Placement of Mount: Passenger side floor board, under seat Drilling Requirements: No - uses existing seat bolts Seat Configuration: Bucket/bench Pole: Purchased Separately Weight: 9.1 lbs. Material: Powder Coated Steel Features: Quick installation with no drilling needed. Rock solid construction with a lifetime warranty. The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. Tough-Tray Dimensions: Tray Depth: 10.0" Tray Thickness: 2.125" Tray Width (Expansion): 10" to 16" Side Clamp Arm Height: 0.5" (min) to 1.75" (max) Material: High Strength Composite The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray. The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12". Material: Powder Coated Marine Grade Aluminum

No-Drill™ Vehicle Base f/ '10-13 Ford Transit Connect + More Compatible Vehicles: Ford Transit Connect (2010-2013) Transit Connect Wagon Premiun (2013) Transit Connect XL Van (2013) Transit Connect XLT Van (2013) Transit Connect XLT Wagon (2013) Dodge Grand Caravan (2008-2009 2012-2016) Grand Caravan AVP (2013) Grand Caravan Crew (2013) Grand Caravan RT (2013) Grand Caravan SE (2013) Grand Caravan SXT (2013) RAM C/V Tradesman Van (2014-2015) Chrysler Town & Country (2008-2009 2012-2016) Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 4.5 lbs. Material: Powder Coated Steel

RAM Mount No Drill Vehichle System f/Nissan NV1500, NV2500HD, NV3500HD &  Toyota Tundra This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens) The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics. Compatible Vehicles: Nissan NV1500 (2011-2021) Nissan NV2500 HD (2011-2020) Nissan NV3500 HD (2011-2020) Toyota Tundra (2007-2021) Features: Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Material: High Strength Composite and Powder Coated Steel Notes: If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.

No-Drill™ Laptop Mount for the Ford F-250, F-350, F-450, F-550, F-650, F-750 & Excursion This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics. Placement of Mount: Passenger side floor board, in front of seat Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket/Bench Material: High Strength Composite and Powder Coated Steel Compatibility Ford F-250 (1997-2016) F-350 (1997-2016) F-450 (1997-2016) F-550 (1997-2016) F-650 (1997-2019, 2021) F-750 (1997-2019, 2021) Excursion (2000-2005)

No-Drill™ Laptop Base for the Ford F-150 & Lincoln Mark LT The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base custom designed to fit this vehicle perfectly. Using the front bench or passenger side seat rail bolts as attachment points, existing hardware is used to secure the laptop mount base in the vehicle. Placement of Mount:  Passenger side floor board, under seat Drilling Requirements:  No - uses existing seat bolts Hole Pattern: Seat Bolt Distance: 11.5" center to center Pole:  Purchased Separately Material: Powder Coated Steel Features:  Quick installation with no drilling needed. Rock solid construction with a lifetime warranty. Compatible Vehicles: Ford F-150 (2004-2014) F-150 Crew Cab (2010) F-150 FX2/FX4 (2012-2014) F-150 Harley Davidson (2012) F-150 King Ranch (2012-2013) F-150 Lariat (2012-2013) F-150 Limited (2012-2013) F-150 Platinum (2012-2013) F-150 Raptor (2013) F-150 Regular Cab (2011) F-150 STX (2012-2013) F-150 Super Cab (2011) F-150 Super Crew (2011) F-150 SVT (2013) F-150 SVT Raptor (2012) F-150 XL (2012-2013) F-150 XLT (2013) Lincoln Mark LT (2005-2011) Note: If you are installing this product into a 2009-2010 F-150 with the slide out cup holder, the RAM-VB-109A is the preferred kit. The standard RAM-VB-109 kit will install but limit the use of the cup holder. To use the RAM-VB-109 with the slide out cup holder, pull the cup holder all the way out if you plan to use it prior to installation. Once installed, the cup holder will not be able to slide back under the center console. The RAM-VB-109A has an adjustable riser that can be positioned so that the cup holder is not interfered with. For base model trucks without the slide out cup holder, the standard RAM-VB-109 kit is ideal.

Compatible Vehicles: Ford Edge (2007-2011) Ford Fusion (2013-2014) This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics. Material: High Strength Composite and Powder Coated Steel Notes: If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.

No-Drill™ Vehicle Laptop System f/97-15 Ford Expedition This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12" to 18". Dual swing arms provide articulation and 12" of reach for passenger and driver access to the mounted device. Rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics. Compatible Vehicles: Ford Expedition (1997-2015) Ford Expedition King Ranch EL (2013) Ford Expedition Limited (2013) Ford Expedition Limited EL (2013) Ford Expedition Ranch EL (2013) Ford Expedition XLT (2013) Ford Expedition XLT EL (2013) Ford F-150 (1997-2003) Ford F-150 Heritage (2004) Ford F-250 Light Duty (1997-2004) Ford Windstar (2004-2007) Specs & Features Placement of Mount: Passenger side floor board, under seat Drilling Requirements: No - uses existing seat bolts Seat Configuration: Bucket/Bench Material: High Strength Composite and Powder Coated Steel Notes:If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit. One 4" riser is included with this vehicle base. Step feature allows minimized amount of intrusion of passenger leg space. This base will not interfere with factory installed console in most installations.

No-Drill™ Vehicle Base f/ '13-21 Ford Fusion + More The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base custom designed to fit this vehicle perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the laptop mount base in the vehicle. Compatible Vehicles: Ford Edge (2007-2013) Edge Limited (2013) Edge SE (2013) Edge SEL (2013) Edge Sport (2013) Fiesta (2015) Fusion (2013-2021) Placement of Mount: Passenger side on the floor, under front seat Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Material: Powder Coated Steel Weight: 6 lbs. Features: Quick installation with no drilling needed

No-Drill Laptop Base for the Ford Explorer and Police Interceptor Utility Compatible Vehicles: Ford Explorer (2011-2012) Ford Police Interceptor Utility (2013) Placement of Mount: Passenger side floor board, in front of seat Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Material: Powder Coated Steel Notes: Utilizes existing vehicle hardware. Plastic trim may be re-installed once the No-Drill base has been secured into vehicle.

RAM® No-Drill™ Vehicle Base for 2019 Ford Ranger The RAM® No-Drill™ laptop mounting base features a stabilizer foot and heavy-duty steel base custom-designed to fit the 2019 Ford Ranger perfectly. Using the passenger side seat rail bolts as attachment points, existing hardware is used to secure the mounting base in the vehicle. Specifications: Placement of Mount: Passenger side, in front, where seat frame meets floor board Drilling Requirements: No. Utilizes existing vehicle mounting points and hardware Seat Configuration: Bucket Pole: Purchased Separately Material: Powder Coated Steel Features: Custom, No-Drill™ mounting base offers lowest profile in the industry Manufactured from high strength steel with a durable powder coat finish If required, high quality fastening hardware is included Mounts using existing seat bolts, no drilling required

Vehicle Base Compatible Vehicles: DODGE RAM 1500-5500 (2008-2011) This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. DRILLING REQUIREMENTS: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 2.1 lbs. Material: Powder Coated Steel Dimensions: A = 14.75", B = 3.8", C = 1.75", Hole Center = 13.25" Features: Quick installation with no drilling needed. Rock solid construction with lifetime warranty. Low profile keeps mount away from passenger leg space. Won?t interfere with levers or factory-installed console or 4WD lever. Designed to accommodate trucks with PTO Swing Arm The RAM RAM-VP-SW1-89, combination swing arm/tele-pole system, will connect to any RAM vehicle base without a welded female tele-pole. Included is a tele-pole with a height range from 11.5" to 17"; it can be easily adjusted by turning the knob at the top of the post. Once the knob has been tightened, the tele-pole becomes a rigid support for any RAM cradle, holder or Tough-Tray. The double swing arm with rotating plate, allows you to twist and tilt the viewing angle of your laptop, tablet, UMPC, monitor, or any other connected electronic device, when mounted on your RAM Vehicle Mount. Taking the highly successful RAM Vehicle Mounts to the next level, this rotating swivel arm gives you even more viewing positions for your mounted electronic device while holding everything firmly in place. The length of the double swing arm is 12". Material: Powder Coated Marine Grade Aluminum Ball Size: 1.5" Rubber Ball "C" Size Note: Part number reflects product packaged in clear clam shell for store shelf display. Laptop Mount Tray The RAM Tough-Tray is spring loaded expandable tray that can accommodate 10 to 16 inch wide laptops. The tray includes four (4) side clamping arm with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS, PDAs or other electronics. Tough-Tray Dimensions: Tray Depth: 10.0" Tray Thickness: 2.125" Tray Width (Expansion): 10" to 16" Side Clamp Arm Height: 0.5" (min) to 1.75" (max) Material: High Strength Composite Note: Part number reflects product packaged in clear clam shell for store shelf display. The Tough-Tray is compatible with laptops that have 17" screens. If the Tough-Tray Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-n-Motion kit.

No-Drill™ Vehicle Laptop Base f/97-15 Ford Expedition The RAM® No-Drill™ laptop mounting base features a heavy-duty steel mounting base custom designed to fit this vehicle perfectly. Using the front bench or passenger side seat rail bolts as attachment points, existing hardware is used to secure the laptop mount base in the vehicle. Compatible Vehicles: Ford Expedition (1997-2015) Ford Expedition King Ranch EL (2013) Ford Expedition Limited (2013) Ford Expedition Limited EL (2013) Ford Expedition Ranch EL (2013) Ford Expedition XLT (2013) Ford Expedition XLT EL (2013) Ford F-150 (1997-2003) Ford F-150 Heritage (2004) Ford F-250 Light Duty (1997-2004) Ford Windstar (2004-2007) Specs & Features Placement of Mount: Passenger side floor board, under seat Drilling Requirements: No - uses existing seat bolts Seat Configuration: Bucket/bench Pole: Purchased Separately Material: Powder Coated Steel Features: One 4" riser is included with this vehicle base. Step feature allows minimized amount of intrusion of passenger leg space. This base will not interfere with factory installed console in most installations.

No-Drill Laptop Base for the Ford Police Interceptor Sedan Compatible Vehicles: Ford Police Interceptor Sedan (2013) Ford Taurus (2013) Placement of Mount: Between the seat cushion and seat frame on passenger side Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Weight: 3.5 lbs. Material: Powder Coated Steel

No-Drill™ Laptop Mount w/ Adjust-A-Pole™ f/ The Dodge RAM 1500-5500 This No-Drill™ Laptop Stand System installs quickly and easily into the specified vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12 to 18 inches. Dual swing arms provide articulation and 12 inches of reach for passenger and driver access to the mounted device. Patented rubber ball and socket joint provides additional adjustment as well as shock and vibration isolation. The RAM Tough Tray™ is spring loaded to accommodate 10" to 16" wide laptops & (17" wide screens). The tray features four adjustable retaining arms with rubber grip feature. These arms can be moved both vertically and horizontally. This allows for a custom fit for varying thicknesses of laptops and the freedom of not blocking ports or drives. A screen support and USB light are also available to accessorize the tray. Hole patterns on perimeter of tray facilitate the mounting of additional RAM systems to support GPS or other electronics. Compatible Vehicles: RAM 1500 (2012-2018) RAM 1500 Classic (2019-2021) RAM 2500-5500 (2012-2021) Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board. Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Material: High Strength Composite and Powder Coated Steel Notes: Low profile design limits intrusion on passenger side leg space. Base will not interfere with levers or factory installed console or 4WD lever. Base designed to accommodate trucks with power take-off (PTO.) If the Tough-Tray™ Laptop Cradle is intended to hold a laptop or device while the vehicle is in motion, we recommend the Secure-N-Motion™ kit.

RAM® No-Drill™ Vehicle Base for 2019 RAM 1500 This heavy duty, steel RAM® No-Drill™ laptop vehicle base is custom-designed for the 2019 Dodge RAM 1500. Using the passenger side seat rail bolts as attachment points, provided hardware is used to secure the mounting base in the vehicle. Specifications: Placement of Mount: Passenger side, front, where seat rail frame attaches to floor board Drilling Requirements: No - attaches to seat studs Seat Configuration: Bucket Pole: Purchased Separately Material: Powder Coated Steel