|
Marine Plumbing & Ventilation
The plumbing and ventilation systems are two of the most important aspects of your boat. It is very important that any toilet facilities work properly, and you also need to ensure that there is adequate ventilation for the engine and to remove any fumes that can build up in passenger compartments or similar areas. With our marine plumbing and ventilation parts and accessories, you have what you need all in one place, right at your fingertips. From air conditioning & refrigeration supplies to bilge pumps, fans, and hot water heaters, we have it all under one roof.
We carry several brands and can offer Livewell pumps and transfer pumps, along with several marine sanitation options. Portable toilets are an excellent choice for boats that are large enough to accommodate them, but the comfort of your passengers is not the only thing to be aware of. You also need to make sure you have adequate engine cooling pumps, and that any washdown / pressure pumps work correctly. With a WaterMaker pump, quality fittings, and the right blowers & heaters for your boat, you can ensure that your boat will operate correctly and your passengers will have the comfort and convenience they need.
|
|
|
20-Gallon Water Heater without Heat Exchanger - 240V
A marine water heater is simply a small, insulated tank downstream of the pump. You must have a pressurized water system to operate a water heater. The pump draws water from the storage tank(s) and fills the water heater tank. Inside the water heater is an electrical heating element and usually a coiled tube called a heat exchanger. When AC power is available, the electrical element (controlled by a thermostat) heats the water. Away from the dock, the hot engine coolant is routed through the coiled tube to heat the water in the tank when the engine is running.
Water heaters have four threaded ports. The tank inlet connects via a tee connector to the outlet hose from the pump. A check valve is required in this line or in the heater to prevent hot water from migrating back toward the pump. The outlet connection supplies heated water to the hot side of all faucets, also using tee connectors. The other two ports are for the heat exchanger connection, which varies depending on engine installation. Use only metal fittings to plumb a water heater, never plastic. If a pressure-release valve isn’t integral, the heater will have a fifth port for this essential component.
Raritan’s 1700 Series Water Heaters are built for the long haul. A glass-lined steel tank and a rust-proof jacket keep the Raritan water heater looking great and lasting for many years. Research has shown that glass-lined steel tanks are more durable than tanks made from just stainless steel. To increase longevity and fluctuations in water quality, Raritan includes a sacrificial magnesium anode that ensures a long tank life.
Features:
High-density non-CFC foam insulation helps the tank to maintain the hot water longer, a plus if you don’t want to run the generator for hot water
The recovery rate is 13 gallons per hour
Hot water at 160 degrees F when mixed with cold water can greatly extend the usable capacity of the tank
Because the heater includes an adjustable thermostat it can be set as high as 160 degrees F
All plumbing connections on one side (it retrofits without difficulty to most onboard pressure systems)
Hot and cold-water fittings are standard 3/4 in. male NPT and the heat exchanger’s 3/4 in. female NPT
Specifications:
Tank Size: 20-gallon
Volts: 240
Benefits:
Simple installation – retrofits to most on-board pressure systems
Proven long-life design
Withstands the rigors of the marine environment
The glass-lined steel tank is more durable than stainless steel
The attractive polymer jacket resists corrosion from dampness
Ignition-protected, adjustable thermostat
Round tanks are designed to withstand more pressure than square tanks
Glass-lined steel tank for long life and high efficiency
Environmentally friendly CFC-free foam insulation
Replaceable magnesium anode to protect the tank and neutralize acids in the water
The tank is covered by a five-year Limited Warranty
Each unit is assembled by hand, individually tested, and backed by Raritan’s two-year Limited Warranty and legendary technical support team
|
1262.20 |
|
|
12-Gallon Water Heater without Heat Exchanger - 240V
A marine water heater is simply a small, insulated tank downstream of the pump. You must have a pressurized water system to operate a water heater. The pump draws water from the storage tank(s) and fills the water heater tank. Inside the water heater is an electrical heating element and usually a coiled tube called a heat exchanger. When AC power is available, the electrical element (controlled by a thermostat) heats the water. Away from the dock, the hot engine coolant is routed through the coiled tube to heat the water in the tank when the engine is running.
Water heaters have four threaded ports. The tank inlet connects via a tee connector to the outlet hose from the pump. A check valve is required in this line or in the heater to prevent hot water from migrating back toward the pump. The outlet connection supplies heated water to the hot side of all faucets, also using tee connectors. The other two ports are for the heat exchanger connection, which varies depending on engine installation. Use only metal fittings to plumb a water heater, never plastic. If a pressure-release valve isn’t integral, the heater will have a fifth port for this essential component.
Raritan’s 1700 Series Water Heaters are built for the long haul. A glass-lined steel tank and a rust-proof jacket keep the Raritan water heater looking great and lasting for many years. Research has shown that glass-lined steel tanks are more durable than tanks made from just stainless steel. To increase longevity and fluctuations in water quality, Raritan includes a sacrificial magnesium anode that ensures a long tank life.
Features:
High-density non-CFC foam insulation helps the tank to maintain the hot water longer, a plus if you don’t want to run the generator for hot water
The recovery rate is 13 gallons per hour
Hot water at 160 degrees F when mixed with cold water can greatly extend the usable capacity of the tank
Because the heater includes an adjustable thermostat it can be set as high as 160 degrees F
All plumbing connections on one side (it retrofits without difficulty to most on-board pressure systems)
Hot and cold-water fittings are standard 3/4 in. male NPT and the heat exchanger’s 3/4 in. female NPT
Specifications:
Tank Size: 12-gallon
Volts: 240
Benefits:
Simple installation – retrofits to most on-board pressure systems
Proven long-life design
Withstands the rigors of the marine environment
The glass-lined steel tank is more durable than stainless steel
The attractive polymer jacket resists corrosion from dampness
Ignition-protected, adjustable thermostat
Round tanks are designed to withstand more pressure than square tanks
Glass-lined steel tank for long life and high efficiency
Environmentally friendly CFC-free foam insulation
Replaceable magnesium anode to protect the tank and neutralize acids in the water
The tank is covered by a five-year Limited Warranty
Each unit is assembled by hand, individually tested, and backed by Raritan’s two-year Limited Warranty and legendary technical support team
|
1130.48 |
|
|
20-Gallon Water Heater with Heat Exchanger - 240V
A marine water heater is simply a small, insulated tank downstream of the pump. You must have a pressurized water system to operate a water heater. The pump draws water from the storage tank(s) and fills the water heater tank. Inside the water heater is an electrical heating element and usually a coiled tube called a heat exchanger. When AC power is available, the electrical element (controlled by a thermostat) heats the water. Away from the dock, the hot engine coolant is routed through the coiled tube to heat the water in the tank when the engine is running.
Water heaters have four threaded ports. The tank inlet connects via a tee connector to the outlet hose from the pump. A check valve is required in this line or in the heater to prevent hot water from migrating back toward the pump. The outlet connection supplies heated water to the hot side of all faucets, also using tee connectors. The other two ports are for the heat exchanger connection, which varies depending on engine installation. Use only metal fittings to plumb a water heater, never plastic. If a pressure-release valve isn’t integral, the heater will have a fifth port for this essential component.
Raritan’s 1700 Series Water Heaters are built for the long haul. A glass-lined steel tank and a rust-proof jacket keep the Raritan water heater looking great and lasting for many years. Research has shown that glass-lined steel tanks are more durable than tanks made from just stainless steel. To increase longevity and fluctuations in water quality, Raritan includes a sacrificial magnesium anode that ensures a long tank life.
Features:
A heat exchanger (the heat exchanger allows the user to heat water when underway by circulating engine cooling fluid through the almost 7-foot-long coil within the tank)
The recovery rate can be as high as 18 gallons per hour
High-density non-CFC foam insulation helps the tank to maintain the hot water longer, a plus if you don’t want to run the generator for hot water
Hot water at 160 degrees F when mixed with cold water can greatly extend the usable capacity of the tank
Because the heater includes an adjustable thermostat it can be set as high as 160 degrees F
All plumbing connections on one side (it retrofits without difficulty to most onboard pressure systems)
Hot and cold-water fittings are standard 3/4 in. male NPT and the heat exchanger’s 3/4 in. female NPT
Specifications:
Tank Size: 20-gallon
Volts: 240
Benefits:
Simple installation – retrofits to most on-board pressure systems
Proven long-life design
Withstands the rigors of the marine environment
The glass-lined steel tank is more durable than stainless steel
The attractive polymer jacket resists corrosion from dampness
Ignition-protected, adjustable thermostat
Round tanks are designed to withstand more pressure than square tanks
Glass-lined steel tank for long life and high efficiency
Environmentally friendly CFC-free foam insulation
Replaceable magnesium anode to protect the tank and neutralize acids in the water
The tank is covered by a five-year Limited Warranty
Each unit is assembled by hand, individually tested, and backed by Raritan’s two-year Limited Warranty and legendary technical support team
|
1333.33 |
|
|
|
|
|
Rule In-Line Blower - 3" Ducting
Part Number: 140
Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule? in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets.
Features
Efficient high-volume air flow
Quiet operation
Low amp draw
Slip-on inlet and outlet ducting connections
Sealed motor shaft for moisture protection
Corrosion resistant nickel-plated motor housing
IMCI (CE)
USCG 183.410 Compliant: Ignition protected
Applications:
Race cars and helmet ventilation
Bus ventilation (engine and bathroom fumes)
Prison van ventilation (cooling, air-freshening)
Blow-up signs and mascots
Tanning booths
Building ventilation
Specifications
Approvals: CE
Dimensions (H x W x D): 76 x 127 x 81 (mm)
ElectricalCharacteristics: 2.9 Amp
Flow Rate (US gallons & litres): 135 CFM @ Open Flow
Fuse Size: 4 (amp)
Product Inlet Fitting: 3" (76 mm) Ducting
Product Outlet Fitting: 3" (76 mm) Ducting
Voltage: 13.6 (Vdc)
WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
39.28 |
|
|
Rule In-Line Blower - 4" Ducting
Part Number: 240
Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule® in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets.
Features
Efficient high-volume air flow
Quiet operation
Low amp draw
Slip-on inlet and outlet ducting connections
Sealed motor shaft for moisture protection
Corrosion resistant nickel-plated motor housing
IMCI (CE)
USCG 183.410 Compliant: Ignition protected
Applications:
Race cars and helmet ventilation
Bus ventilation (engine and bathroom fumes)
Prison van ventilation (cooling, air-freshening)
Blow-up signs and mascots
Tanning booths
Building ventilation
Specifications
Approvals: CE
Dimensions (H x W x D): 102 x 152 x 106 (mm)
ElectricalCharacteristics: 4.3 Amp
Flow Rate (US gallons & litres): 235 CFM @ Open Flow
Fuse Size: 7 (amp)
Product Inlet Fitting: 4" (102 mm) Ducting
Product Outlet Fitting: 4" (102 mm) Ducting
Voltage: 13.6 (Vdc)
WARNING: This product can expose you to chemicals including STYRENE which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
42.97 |
|
|
Turbo 4000 Series II In-Line Blower
Part #: 1749-4
Attwood's improved Turbo 4000 Series II sets the standard for in-line blower performance. Utilizing advanced fan blade design techniques, Attwood has developed a blower system that matches air flow of existing in-line blowers at a significantly reduced noise level. The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size.
Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads.
Features:
Nickel-plated motor can for corrosion resistance
Stiffening ribs to reduce housing distortion
Motor cap to seal wires and motor for water resistance
Five-blade fan maximize airflow and efficiency
Tabs in intake and exhaust hold ventilation hose/clamp firmly in place
Low amp draw motor for longer blower and battery life
Built-in mounting feet allow easy vertical or horizontal install
3-Year Warranty
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
29.63 |
|
|
Turbo 3000 Series In-Line Blower
Part #: 1733-4
The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size.
Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads with optional MP1 molded rubber connectors. Improved 3" design.
Features:
Nickel-plated motor can for corrosion resistance
Stiffening ribs to reduce housing distortion
Motor cap to seal wires and motor for water resistance
Five-blade fan maximize airflow and efficiency
Tabs in intake and exhaust hold ventilation hose/clamp firmly in place
Low amp draw motor for longer blower and battery life
Built-in mounting feet allow easy vertical or horizontal install
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
25.88 |
|
|
Date: March 1, 2011
Field Notice Number: 311-C11
Models or Product Affected: Cruisair & Marine Air Systems
Immediate Action Is Required In Order To Avoid Damage To Your Vessel
Please see these two PDF's
311-C11_POE-Oil-With-CPVC-Plumbing
301-F10_Antifreeze Mandatory For Chillers
|
|
|
Heavy Duty Flangemount Blower
Heavy Duty Blowers are designed for applications such as commerical or high use engine room ventilation and extraction where a long life requirement demands heavy duty motors with long brush life. Built to provide the same high outputs as our standard specification blowers.
5,000 hr motor life for the heaviest of applications
Continuous duty
Efficient high volume air flow
Outlet flange mounts directly on bulkhead
Slip on inlet ducting connection
Low current draw
Corrosion resistant materials throughout
Dimensionally stable quiet running Delrin rotors
Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection)
ISO 9097 MARINE (Electric Fans)
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
286.91 |
|
|
3" In-Line Blower
Inlet/Outlet - 3"
CFM - 158
Johnson Pump in-line blowers provide ventilation for bilges, engine compartments, galleys, and heads.
Made from high quality ABS plastic construction, corrosion resistant motors, and premium electrical connections completes these blowers
Five blade, quiet, highly efficient, and reliable operation will provide years of long life
Compact and with mounting feet makes it easy to install on any flat surface
|
42.96 |
|
|
4" In-Line Blower
Inlet/Outlet - 4"
CFM - 240
Johnson Pump in-line blowers provide ventilation for bilges, engine compartments, galleys, and heads.
Made from high quality ABS plastic construction, corrosion resistant motors, and premium electrical connections completes these blowers
Five blade, quiet, highly efficient, and reliable operation will provide years of long life
Compact and with mounting feet makes it easy to install on any flat surface
|
44.45 |
|
|
keywords: Xtreme heaters, boat heater, marine heater, engine heater, heater
|
|
|
1700 Series Water Heater
120v
12 Gallon
With Engine Heat Exchanger
The "1700 Series" water heater provides hot water for galley and shower. Dense foam insulation provides better and longer heat retention than traditional fiberglass. The tank itself is protected by a 75 PSI T& P (temperature and pressure) relief valve. The cylindrical design of the tank enables it to withstand more pressure than a cube shaped tank.
Heat exchanger models can be connected to the engine cooling system. This provides the added convenience of hot water when underway or generator power is not available. The innovative heat exchanger is over seven feet in length and is evenly coiled throughout the interior of the tank, providing hot water rapidly and efficiently.
Raritan's water heaters use an ignition protected thermostat. Although it is factory set to 120°F, it is adjustable from 110° to 160°F and has a safety shut down limit of 190°F. All models and sizes have the plumbing connections on the same side to simplify installation. Hot and cold water connections are 3/4" male NPT (National Pipe Thread). Heat exchanger connections are 3/4" female NPT.
Benefits:
Simple installation - retrofits to most on-board pressure systems
Proven long-life design
Withstands the rigors of the marine environment
Glass-lined steel tank is more durable than stainless steel
Attractive polymer jacket resists corrosion from dampness
Ignition-protected, adjustable thermostat
Round tanks are designed to withstand more pressure than square tanks
Glass-lined steel tank for long life and high efficiency
Environmentally friendly CFC-free foam insulation
Replaceable magnesium anode to protect tank and neutralize acids in the water
The tank is covered by a five-year Limited Warranty
Each unit is assembled by hand, individually tested and backed by Raritan's two-year Limited Warranty and legendary technical support team
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
1220.22 |
|